Rajguru Electronics

Lamington Road, Mumbai, Maharashtra

This module is a low cost embedded UART-ETH- WIFI Module (Serial port -Ethernet- wireless network) developed by Rajguru electronics.
This product is an embedded module based on the Universal serial interface network standard, built in TCP/IP protocol Stack. enabling the user serial port, Ethernet, Wireless Network (WiFi), interface between the conversions.
Through the module, the traditional serial devices do not need change any configuration; data can be transmitted through the internet network. Provide a quick solution for the user's devices to transfer data via ethernet.

Introduction

ARM7 LPC2148 Development Board is a powerful development platform based on LPC2148 ARM7TDMI microcontroller with 512K on-chip memory. This board is ideal for developing embedded applications involving high speed wireless communication, USB based data logging, real time data monitoring and control, interactive control panels etc. The on-chip USB controller provides direct high speed interface to a PC/laptop with speeds up to 12Mb/s. The UART boot loader eliminates need of an additional programmer and allows you to program using serial port. The on board peripherals include SD/MMC card interface, USB2.0 interface, 4Kbit I2C EEPROM, Xbee wireless module interface, ULN2003 500mA current sinking driver, L293D DC motor controller, 16X2 character LCD and many more. The on-chip peripherals and the external hardware on the development board are interconnected using pin headers and jumpers. The I/O pins on the microcontroller can be accessed from a 50 pin male header. The board is made from double sided PTH PCB board to provide extra strength to the connector joints for increased reliability. It supports the operating supply voltage between 7V to 14V and has built-in reverse polarity protection.

Specifications

• Microcontroller: LPC2148 with 512K on chip memory
• Crystal for LPC2148: 12Mhz
• Crystal for RTC: 32.768KHz
• 50 pin Berg header for external interfacing
• Operating Supply: 9V to 12V DC/AC
• 2.4GHz ZigBee (XBee) wireless module adaptor
• 512 bytes of I2C external EEPROM
• USB Type B Connector
• SD / MMC card holder
• 10pin(2X5) FRC JTAG connector for flashing and debugging
• 50 Pin Expansion header
• 2x16 Character Alphanumeric LCD
• L293D 600mA Dual DC motor Driver
• ULN2003 500mA driver
• Dual RS232 UARTs for external communication
• Real-Time Clock with Battery Holder
• 2 Analog Potentiometers connected to ADC
• TSOP1738 IR receiver
• 4 USER Switches
• 4 USER LEDs
• Reset and Boot loader switches
• 3V button cell for on chip RTC
• ON/OFF switch
• Buzzer
• Schematics and Application examples in KEIL provided in the documentation CD

Kit Contains1-LPC2148 Pro Development Board1-USB Cable1-DB9 Serial CableA set of 10 1-1 cables1-Documentation CD

LPC2148 Features

• 16-bit/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package.
• 40 kB of on-chip static RAM and 512 kB of on-chip flash memory.
• In-System Programming/In-Application Programming (ISP/IAP) via on-chip boot loader software.
• Embedded ICE RT and Embedded Trace interfaces offer real-time debugging with the on-chip Real Monitor software and high-speed tracing of instruction execution.
• USB 2.0 Full-speed compliant device controller with 2 kB of endpoint RAM.
• Two 10-bit ADCs provide a total of 14 analog inputs
• Single 10-bit DAC provides variable analog output
• Two 32-bit timers/external event counters (with four capture and four compare channels each), PWM unit (six outputs) and watchdog.
• Low power Real-Time Clock (RTC) with independent power and 32 kHz clock input.
• Multiple serial interfaces including two UARTs, two Fast IC-bus (400 kbit/s), SPI and SSP with buffering and variable data length capabilities.
• Vectored Interrupt Controller (VIC) with configurable priorities and vector addresses.
• Up to 45 of 5 V tolerant fast general purpose I/O pins in a tiny LQFP64 package.
• 60 MHz maximum CPU clock available from programmable on-chip PLL with settling time of 100 us.
• On-chip integrated oscillator operates with an external crystal from 1 MHz to 25 MHz
• Power saving modes include Idle and Power-down.
• Individual enable/disable of peripheral functions as well as peripheral clock scaling for additional power optimization.
• Processor wake-up from Power-down mode via external interrupt or BOD.
• Single power supply chip with POR and BOD circuit
• CPU operating voltage range of 3.0 V to 3.6 V (3.3 V - 10 pct) with 5 V tolerant I/O pads.