Ricon Dynamic Engineers Ahmedabad, Gujarat

capacity : 150 cfm to 85, 000 cfm (200 cmh to 1, 40, 000 cmh)   pressure : 50 mm wc to 1500 mm wc (2” wc to 60” wc)   motor hp : 1 hp to 200 hp   type : induced draught, forced draught   moc : ms, ss 304, 316, 316l, frv, frp application :   industrial furnace and boiler, chemical processing plant, textile plant, cement plant, dairy refrigeration plant, gas and oil firing burner, dust collecting system, ceramic industries, petro – chemical plant, power plant, air conditioning plant, ventilation system (in hotels, hospitals, restaurant, residents, cinema hall, tunnel etc.), pneumatic conveying system of powder and granules. unique features :   the ricon blowers are backed by computer software or design selection and detailed performance characteristics. It can offer low pressure ventilation fans with very high air volume and also makes very high pressure fan. It can offer various types of shaft seals to avoid leakages of gases. The ricon blowers have careful design against noise pollution.   to suit the specified application, we design and furnish     split housing construction   inlet box   inlet box damper   variable inlet vanes   back pull – out design   vibration isolators   outlet damper   coupling & belt guard   inspection door   drain plugs   flexible connectors on inlet and outlet of the fan   isolated bearing pedestal support stand   shaft seals – labrinth seals   stuffing box   heat sling   bearing cooling arraignment   high temperature fans

Double Flap Valves, also known as Double Flap Valves or Double Flap Gates, are a type of airlock valve commonly used in industrial applications as a component in bulk material handling applications.   Double Dump Valves are primarily used to discharge chunky, pellets, granules or fibrous, bulk materials from hoppers, bins, and cyclones operating under positive or negative pressure.   Double dump valves are used to discharge a flow of material while at the same time serving as an airlock transition point to preserve the pressure differential above and below the valve.   This type of material handling valve is ideal for use with bulky or abrasive materials that would tend to jam or damage aRotary Feeder   Double dump valves have two trap-door flap plates which open and close on an alternating cycle. The top gate opens to allow collected material to drop through onto the bottom gate. The top gate then re-closes to prevent air leakage above the valve. The bottom gate then opens to allow material to pass completely through the valve. The bottom gate then re-closes to prevent air leakage below the valve. This cycle is continuously repeated in order to maintain a steady discharge of material from the valve, while maintaining a positive seal on the system.   Each flap plate has its own pneumatically operated cylinder and solenoid valve. The timing of the valve is controlled by an electronic signal sent to the solenoid valves. This method of operation is design to provide first class automation with sequential controller for accurate timing of the desire functioning of the valve.  

The RICON Dual Tunnel type diverters have been specially designed to route powders and pellets with minimum degradation in pneumatic conveying systems. The RICON plug type diverter is applied in the chemical, pharmaceutical, plastic, food and other related industries.   The RICON plug type diverter consists of an Aluminum housing and end covers in which a plug with two pipes is installed. All product contact surfaces are made from SS 304. Three approved silicone seals guarantee the sealing between housing and plug. The body is pressure tight, so ensuring no leakage to atmosphere. The standard diverter can be used in systems with positive pressures up to 3 bar g (static seals). The sizes 50-150 are optionally available for pressures up to 6 bar g (inflatable seals). The RICON Dual Tunnel Diverter Valve is supplied with a complete electro pneumatic control system, including solenoids and inductive position sensors. The standard diverter can be used for product temperatures ranging from –25 °C up to +80 °C at ambient temperatures of –10 °C up to +40 °C. Versions for higher temperatures are available on request.  

We, at Ricon Engineers design and manufacture one of the most vital products in industrial powder handling process. This are called Rotary Air Lock Feeder. Handling powder material is a very complicated process and unless we discuss and understand our buyers exact requirement, then only we go into the further process. This is our fundamental policy since 1979, when we put our foot into the Rotary Air Lock Valves manufacturing activities.