Rs Form Teknic

Dombivali, Mumbai, Maharashtra

The Button Punch Snap Lock / BP Snap Lock ducting Machines form a two piece seam that greatly simplifies ductwork assembly. The male seam is a button, the female seam is a lock and the two snap together for a flush corner. These ducting machines can form 20 to 30 gauge sheet metal into female locks on the inboard and button punched right angle flanges on outboard rolls at speeds of 60-65 fpm and are available in seven and nine forming station ducting machines. Not only do these locks assemble twice as fast as traditional methods, but because the two pieces nest, they are easier to transport too.

Standard with Lockformer quality construction, these ducting machines have Baldor motors; high precision needle-type bearings; heavy chassis plate; case-hardened and ground roll shafts; and arc-welded steel stands protected with Lockformers top-quality primer and paint finish. Alternate fittings are easily accessible from a main transmission bearing lubrication panel.

Beading Machines / Ft Beader is a cost-conscious way to stiffen ductwork. It is 5 times faster than the old method, cross-braking, and uses only one operator. Designed to meet the requirements of SMACNA, this ductwork prep machines produces 5 beads on 12" centers and is adjustable to 3/16" depth. A convenient handwheel raises or lowers, the top roll assembly to set depth of bead. The top and bottom rollers are kept parallel with adjustable screw and pillow block assemblies connected by a link chain. Individual adjustable screw and pillow block assemblies connected by a link chain. Individual collared beading rolls are replaceable.
Feed rolls are self-compensating over the entire gauge range. Double entrance feed bars are provided so that material can be gauged from either left or right side. Standard with Lockformer quality construction, this machine has a Baldor motor; high precision needle-type bearings; turned, ground, and polished steel forming rolls and roll shafts; and an arc-welded steel stand protected with Lockformer's top-quality primer and paint finish. Lubrication fittings are located on each bearing.

This machines is ideal for forming TDCT Fittings and Wrap Duct

The Iowa Precision Folding machine is a motorized Bending Machines with PLC control used in bending the duct blanks having TDC flanges made on it. Simple dial and pointer bend angle setting. The Folding machine has a slotted bed and solid top forming beam. It is designed to form an L-section or Wrap (one-piece) TDC duct. The TDC Notch Locator positions the duct in the proper bending location for forming. This allows one-person operation. The machines is also designed to form various length fittings with a TDC Flange and Pittsburgh or Snap Lock seams.

We recommend the Folding machine be ordered with the optional precision Back Gauge. This back gauge has a digital readout and allows you to preset the bend dimension. This also allows production bending jobs to be run with consistent piece to piece dimensional accuracy

Power Flanging - Lockformer turns up the power

These ductwork prep machines automatically follow any edge -curved or straight.
Use the convenient table slot to turn up a "starting flange" and let it go! A calibrated dial can be set for radii as small as 3-1/4" / 83 mm (or 2"/ 50mm when auto-guide is de-activated). Automatically flange 16 to 26 gauge material at speeds of 18 fpm / 5, 5 Mpm. A non-releasing type head is suitable for open-end fittings, straight and irregular curves.
Standard with Lockformer quality construction, this machines has a Baldor motor, and an arc-welded steel stand protected with Lockformer's top-quality primer and paint finish.

The quiet, automated way to close Pittsburgh seams and make ducting in less than six seconds !

Eliminate hammering to close Pittsburgh lock ducting seams.

Greatly reduce noise levels and speed up duct seam Closing in your shop or at the job site. Seam Closing MachineT will also close both insulated and reinforced ductwork