We are offering rod seals are considered to be one of the decisive factor for the functioning of the hydraulic cylinder. Leakage through the rod seal can cause accidents / environmental damages. It is important to properly pair the rod seal & wiper for the best sealing performance. If a less aggressive rod seal is paired with an aggressive wiper, the wiper can scrape off the microscopically thin film of oil that remains on the rod in microscopic surface imperfections during the return stroke, resulting in system leakage. The thickness of the oil film depends upon the surface finish, rod seal and surface speed of cylinder. type of rod seal

• single acting / unidirectional rod seals (capable of sealing from one side)
• double acting /bidirectional rod seals (capable of sealing from both sides)

below mentioned are single acting as well as double acting rod seals being offered for different pressure, rod surface speed, pressure media.

We, at sam engineers are engaged in manufacturing, exporting and supplying v ring seals. The v ring seals, also called as axial shaft seals, are manufactured as per the set industrial standards using well-tested material. The clients can avail the v ring seals from us in varied specifications as per the requirement at affordable price. v ring seals types

• all rubber v ring are known as v ring seals
• metal cased v ring seals

parts of v ring sealsthe v-seal is comprised of three basic parts. The body of the seal holds it into place on the shaft or mounting surface. The cone shaped flexible lip rides in light contact with the counter surface and does the sealing. The resilient hinge joins the other two parts together and provides the force which keeps the lip against the counter surface. It is these three parts, working together, which allows simple one piece seal to do what no other seal system can do. installationsthe v-seal can be completely assembled without the need of tools. Being all rubber, it can stretch up to 250% of its molded i.d., so it can be easily stretched over flanges, collars, and entire bearing housings during assembly. This same resilience holds the seal in place without the need for springs or clamps. To assemble the seal, it is stretched onto the shaft by hand and then pushed up against the counter face to a pre-determined width. seal functionone v-seal functions as three different seals. The simple v-seal lip keeps dirt and water out, grease in and acts as a slinger. The v-seal can be used alone to seal lubrication in and/or contamination out, or it can supplement an oil seal, mechanical seal or labyrinth, keeping contamination away from the primary seal. speedin most applications, the v-seal rotates with the shaft to provide a slinging action. As such, it is subject to centrifugal force. At speeds below 1600 surface feet per minute (fpm), the stretch tension of the v-seal is sufficient to hold it onto the shaft.

• above 1600 fpm, axial back up is required in the form of a step in the shaft or a snap-ring or lock collar
• above 2400 fpm, radial back up is required in the form of a mounting pocket or clamp around the v-seal body. Above 3000 fpm, the lip of the v-seal lifts away from the counterface resulting in a clearance seal and eliminating drag and wear. The v-seal can also be mounted stationary and run against a rotating counterface. In this case, centrifugal force has no effect on the v-seal

the v-seal should always have axial back up in oil applicationsthe basic dimensions of the v-seals are as follows: (i.e for a v-25 a).

• d the molded inside diameter of the v seal =0.87
• d1 - the shaft range the v-seal is made to fit = .095-1.07
• d2 - the maximum i.d. Of the counterface = d1 + 0.08
• d3 - the minimum o.d. Of the counterface = d1 + 0.45
• a - i.d. Width of the v-seal = .018
• b - o.d. Width of the v-seal = 0.3
• c - v-seal cross section = 0.1 b1 v-seal fitted width = 0.24+/-0.03

materialsthe v-seal is available in a variety of different rubber materials for various operating conditions. Nitrile, neoprene, hnbr, epdm and silicone v-seals can all be supplied. Our proprietary anti-friction treatment (aft) reduces the already low friction of the v-seal even further.food grade materials are available including fda and nsf approved rubbers. In addition, our compounding lab can develop specialty materials for particular applications. For additional information, see our materials section or contact our technical department.for more details on sizes available, elastomer suitability or for any further queries.

We are trusted Oil Seals Manufacturer and Supplier in Mumbai. The Oil Seals, we offer, are manufactured using well-tested raw material and are further tested at NABL accredited laboratories. The clients can avail the Oil Seals from us in varied specifications at the market leading price. DetailsIn an Oil seal environment, there is shaft that is rotating inside a housing or bore. Because of the friction, there must be some clearance between the shaft & the bore. The function of the rotary seal / oil seal is to stop whatever fluid is inside from leaking out from the clearance. The oil seal may also be used to prevent outside material such as dirt from moving in the through the surface. "Dynamic sealing" is the relationship between the rotating shaft and the seal and is handled by the sealing element. A garter spring may used in the oil seal to increase the radial interference between the oil seal lip and contact point on the shaft. In order to achieve this interference, the oil seal's ID must be slightly smaller than the diameter of the shaft. "Static sealing" is the relationship between the housing and the seal. In order to achieve this interference, the oil seal's OD must be slightly larger than the diameter of the housing or bore. An oil seal normally consists of three basic components: the sealing element, the metal case and the spring. The purpose of the sealing element is to stop the fluid from leaking between the shaft and housing. The metal case will give rigidity and strength to the seal while it is being held in the bore or recessed groove. The spring will help make the sealing element more effective. All materials must be selected depending on the environment in which the oil seal will function.

Available with us is the precision-made Wiper Seals. The Wiper Seals, we offer, are also known as Dirt Wipers, Scrappers or excluders and extensively used keep contaminants such as dirt, dust & moisture from entering the fluid power systems. The clients can avail the Wiper Seals from us at the most affordable price. Design CriteriaPremature failure of seals or any component in fluid power system is due to contamination. Poor selection of wiper seal can result into failure of Rod seals. Design criteria for the wiper seal should not be limited to allow the proper fitment of rod seal (dynamic sealing ) but also sealing of housing ( static function ) has to be taken care of. Below mentioned are the various profiles of the wiper seal designed to suit the basic requirement of containing the contaminant. Design & selection criteria of the wiper seal is largely depend upon the surface speed of rod, fluid media, rod surface finish & speed. Single lip design or straight wiper lip design offers best scrapping & dirt removal performance. It is recommended for most sealing applications with high contamination. Single lip beveled wiper lip is less aggressive as it allows microscopically thin oil film to be retracted back into the system while providing adequate dirt exclusion in less contaminated environments. Wiper seal with double lip i.e internal as well as external lip provides best sealing performance. It eliminates built up fluid pressure between wiper & rod seal. For applications where equipment is exposed to highly contaminated with dirt, mud, moisture or where the position of the rod seals are such that it is possible for moisture or other contaminants to get past the wiper, leading to the corrosion or damage of components & seals. For these applications, we are offering special environment seals.

We are offering rod seals are considered to be one of the decisive factor for the functioning of the hydraulic cylinder. Leakage through the rod seal can cause accidents / environmental damages. It is important to properly pair the rod seal & wiper for the best sealing performance. If a less aggressive rod seal is paired with an aggressive wiper, the wiper can scrape off the microscopically thin film of oil that remains on the rod in microscopic surface imperfections during the return stroke, resulting in system leakage. The thickness of the oil film depends upon the surface finish, rod seal and surface speed of cylinder. type of rod seal

• single acting / unidirectional rod seals (capable of sealing from one side)
• double acting /bidirectional rod seals (capable of sealing from both sides)

below mentioned are single acting as well as double acting rod seals being offered for different pressure, rod surface speed, pressure media.

We, at sam engineers are engaged in manufacturing, exporting and supplying v ring seals. The v ring seals, also called as axial shaft seals, are manufactured as per the set industrial standards using well-tested material. The clients can avail the v ring seals from us in varied specifications as per the requirement at affordable price. v ring seals types

• all rubber v ring are known as v ring seals
• metal cased v ring seals

parts of v ring sealsthe v-seal is comprised of three basic parts. The body of the seal holds it into place on the shaft or mounting surface. The cone shaped flexible lip rides in light contact with the counter surface and does the sealing. The resilient hinge joins the other two parts together and provides the force which keeps the lip against the counter surface. It is these three parts, working together, which allows simple one piece seal to do what no other seal system can do. installationsthe v-seal can be completely assembled without the need of tools. Being all rubber, it can stretch up to 250% of its molded i.d., so it can be easily stretched over flanges, collars, and entire bearing housings during assembly. This same resilience holds the seal in place without the need for springs or clamps. To assemble the seal, it is stretched onto the shaft by hand and then pushed up against the counter face to a pre-determined width. seal functionone v-seal functions as three different seals. The simple v-seal lip keeps dirt and water out, grease in and acts as a slinger. The v-seal can be used alone to seal lubrication in and/or contamination out, or it can supplement an oil seal, mechanical seal or labyrinth, keeping contamination away from the primary seal. speedin most applications, the v-seal rotates with the shaft to provide a slinging action. As such, it is subject to centrifugal force. At speeds below 1600 surface feet per minute (fpm), the stretch tension of the v-seal is sufficient to hold it onto the shaft.

• above 1600 fpm, axial back up is required in the form of a step in the shaft or a snap-ring or lock collar
• above 2400 fpm, radial back up is required in the form of a mounting pocket or clamp around the v-seal body. Above 3000 fpm, the lip of the v-seal lifts away from the counterface resulting in a clearance seal and eliminating drag and wear. The v-seal can also be mounted stationary and run against a rotating counterface. In this case, centrifugal force has no effect on the v-seal

the v-seal should always have axial back up in oil applicationsthe basic dimensions of the v-seals are as follows: (i.e for a v-25 a).

• d the molded inside diameter of the v seal =0.87
• d1 - the shaft range the v-seal is made to fit = .095-1.07
• d2 - the maximum i.d. Of the counterface = d1 + 0.08
• d3 - the minimum o.d. Of the counterface = d1 + 0.45
• a - i.d. Width of the v-seal = .018
• b - o.d. Width of the v-seal = 0.3
• c - v-seal cross section = 0.1 b1 v-seal fitted width = 0.24+/-0.03

materialsthe v-seal is available in a variety of different rubber materials for various operating conditions. Nitrile, neoprene, hnbr, epdm and silicone v-seals can all be supplied. Our proprietary anti-friction treatment (aft) reduces the already low friction of the v-seal even further.food grade materials are available including fda and nsf approved rubbers. In addition, our compounding lab can develop specialty materials for particular applications. For additional information, see our materials section or contact our technical department.for more details on sizes available, elastomer suitability or for any further queries.

We are trusted Oil Seals Manufacturer and Supplier in Mumbai. The Oil Seals, we offer, are manufactured using well-tested raw material and are further tested at NABL accredited laboratories. The clients can avail the Oil Seals from us in varied specifications at the market leading price. DetailsIn an Oil seal environment, there is shaft that is rotating inside a housing or bore. Because of the friction, there must be some clearance between the shaft & the bore. The function of the rotary seal / oil seal is to stop whatever fluid is inside from leaking out from the clearance. The oil seal may also be used to prevent outside material such as dirt from moving in the through the surface. "Dynamic sealing" is the relationship between the rotating shaft and the seal and is handled by the sealing element. A garter spring may used in the oil seal to increase the radial interference between the oil seal lip and contact point on the shaft. In order to achieve this interference, the oil seal's ID must be slightly smaller than the diameter of the shaft. "Static sealing" is the relationship between the housing and the seal. In order to achieve this interference, the oil seal's OD must be slightly larger than the diameter of the housing or bore. An oil seal normally consists of three basic components: the sealing element, the metal case and the spring. The purpose of the sealing element is to stop the fluid from leaking between the shaft and housing. The metal case will give rigidity and strength to the seal while it is being held in the bore or recessed groove. The spring will help make the sealing element more effective. All materials must be selected depending on the environment in which the oil seal will function.

Available with us is the precision-made Wiper Seals. The Wiper Seals, we offer, are also known as Dirt Wipers, Scrappers or excluders and extensively used keep contaminants such as dirt, dust & moisture from entering the fluid power systems. The clients can avail the Wiper Seals from us at the most affordable price. Design CriteriaPremature failure of seals or any component in fluid power system is due to contamination. Poor selection of wiper seal can result into failure of Rod seals. Design criteria for the wiper seal should not be limited to allow the proper fitment of rod seal (dynamic sealing ) but also sealing of housing ( static function ) has to be taken care of. Below mentioned are the various profiles of the wiper seal designed to suit the basic requirement of containing the contaminant. Design & selection criteria of the wiper seal is largely depend upon the surface speed of rod, fluid media, rod surface finish & speed. Single lip design or straight wiper lip design offers best scrapping & dirt removal performance. It is recommended for most sealing applications with high contamination. Single lip beveled wiper lip is less aggressive as it allows microscopically thin oil film to be retracted back into the system while providing adequate dirt exclusion in less contaminated environments. Wiper seal with double lip i.e internal as well as external lip provides best sealing performance. It eliminates built up fluid pressure between wiper & rod seal. For applications where equipment is exposed to highly contaminated with dirt, mud, moisture or where the position of the rod seals are such that it is possible for moisture or other contaminants to get past the wiper, leading to the corrosion or damage of components & seals. For these applications, we are offering special environment seals.