Ahmedabad, Gujarat, India
Verified
Add Review
Our Products
The Bresle Test Kit supplies all the necessary equipment to test for chloride and soluble salt surface contaminants on blasted surfaces in compliance with ISO 8502-6 & ISO 8502-9.The test is highly important in view of Non visible salts present on the surfaces can lead to premature failures. Many coatings fail due to salts such as chlorides and sulphates contaminating the surface prior to the coating application.
This contamination can be tested quickly and simply using the Bresle Test Kit. This kit has advantage over portable units. Test can be quickly performed at site, shop floor and plants.
The Bresle Patch is attached to the surface; the distilled water is injected with a syringe then extracted, repeat ten cycles of injecting and extracting then measure with the Conductivity Meter. Compact conductivity meter will measure the quantity of salts in μg/cm2 (ppm) and mg/m2. Bresle test complies with ISO 8502-6, which relates to the extraction of soluble contaminants and ISO 8502-9, which relates to the conductometric determination of soluble salts. Calibration Certificates traceable are available for the Conductivity Meter in the kit.
The Bresle Test Kit is supplied with 50 Bresle Patches, 1 Conductivity Meter, Calibration Solutions, 5x5ml Syringes, 25ml Beaker and 250ml Distilled Water. Additional Bresle Patches can be purchased to carry out further tests using this kit.
Part Numbers: BTK-001 Bresle Test Kit BTK-002 Bresle Patches (Pack of 50 Nos.) BTK-003 Bottle 250ml - Distilled Water.
60 Degree angle for semi-gloss
Measuring mode: basic measurement, statistical measurement, continuous measurement, QC measurement (only for GQC6 software)
Continuous mode to check uniformity over large areas
Care:
Tape is delicate, handle with care. Keep tape clean and dry. After each use, wipe clean and apply a light rust preventive oil*. Store in tape container and in a low moisture environment. * White Easy to Read tapes Stainless or 1095 Spring Steel - Do not oil or use solvents to clean this product. White Easy to Read 1095 Spring Steel must be stored in a low moisture environment to prevent rust. No periodic adjustments are needed. Make sure the tape has not been stepped on or kinked, which may destroy the accuracy.
|
|
|
|
| Range | 10-50cN.m (1-5kgf.cm) | ||
| Accuracy | clockwise | ±3% | |
| counter-clockwise | ±4% | ||
| Resolution | 0.1cN.m/0.01kgf.cm | ||
| Size of shank | 1/4″ | ||
| Power supply | 1xAAA battery | ||
| Length | 193mm | ||
| Weight | 190g | ||
|
|
|
|
|
| Code | Range | Accuracy |
| 815-360-01 | 0-360° | ±5 ‘ |
ong wave ultraviolet light at 365 nanometers. A built-in, quiet operating fan located at the rear of the ZB-100F lamp housing dramatically reduces operating temperatures to under 85F, for improved operator safety and comfort while simultaneously extending bulb life.
| Type | Reading | Range | Graduation |
| J158/0 | 0.1mm | 0-200mm | 10-0 |
| J158A/3 | 0.01mm | 0-200mm | 100-0 |
| J158A/1 | 0.001inch | 0-8inch | 100-0 |
Digital MicrometersAvailable upto 100 mm.Each micrometer supplied with a certificate of calibration.Real value for money.
METRICIS 2967 1983ISO 3611 1978DIN 863 (Part 1) 1999JIS B 7502 1994
INCHAmerican Standard(FEDERAL GGG-C-105C)
Other Information
Masters form the base standards when it comes to comparative measurement of components on the shop floor. Master Setting Rings and Discs when calibrated become the basic operational standards in general metal working industry.
Our offered range of surface plate is extensively used for tool making, inspection, spotting and gauging purposes. Highly durable, reliable, resistant to corrosion and are easy to maintain, these surface plate make an ideal base for mounting sophisticated mechanical, electronic and optical gauging systems. Moreover, to meet the specific requirements of our clients, we can also be customized.
| Length | Width | Thickness | Accuracy As Per IS-7327-1991 Grade ’0′ | Approximate Weight in Kgs |
| 400 mm | 400 mm | 60 mm | 4.5 mm | 30 |
| 630 mm | 400 mm | 80 mm | 5.0 pm | 65 |
| 630 mm | 630 mm | 80 mm | 5.0 PM | 100 |
| 1000 mm | 630 mm | 150 mm | 6.0 pm | 295 |
| 1000 mm | 1000 mm | 150 mm | 7.0 pm | 470 |
| 1600 mm | 1000 mm | 200 mm | 8.0 pm | 1000 |
| 2000 mm | 1000 mm | 200 mm | 9.5 pm | 1300 |
Samruddhi Industries, pioneers in manufacturing Pinhole Detector and ancillary testing equipments, now offers the latest innovative Model PD-90 that confirms the chemical fabrication field proven cases with advanced Technology in solid state circuitry that is simplified & more efficient with reliability.
We are offering a precision engineered range of lab testing equipment or laboratory testing equipment that are extensively used in various laboratory experiments. These high performance equipment undergo various quality checks to ensure their accuracy in readings and high reliability. Easy to setup and use, these can also be offered in specific configurations, as per clients definite needs. Moreover, these can also be customized as per the specific requirements of our clients and can be availed from us at competitive prices.
Our range includes:
Torque wrenches are the normally used torque tools available in ratcheting and non- ratchetingmodels. Ratcheting models are used for easy operations. Different models available from 3 NM to 2700 NM.
FEATURES TQC DUST TEST KIT
SCOPE OF SUPPLY
Block & square L. C. 0. 02mm. and 0.01mmV-groove on bottom for shaftsSupplied with adjusting wrench
We have RSK, japan, Milhard, Insize, Samsonic, Precise Brand level bottles available
Features:-
Fixed probe type Coatmeter is a family of Coatmeters designed on the magnetic principle. It is available in three different models and customer can select the appropriate model depending upon his accuracy requirements and application. All these models are useful for measurement of thickness of non magnetic coating on magnetic base material.
The coating may be material like :As Plating : Gold, Copper, Zinc, Tin, Chromium, Hard Chromium, Lead etc.As Coating : Paint, Insulation, Resin Coating.As Lining : Resin, Rubber, fiberglass.As Film : Plastic, non magnetic Metal foils.
The magnetic base may be of material like :Iron, Nickel, Cobalt, Magnetic Stainless Steel etcFeatures :
1.Portable2.Reading can be locked3. Calibration facility with Standard calibration foils4.Can be used in any position5.The reading is available on dial with meter scale on mirror6. Supplied with attractive wooden case
Coating Thickness Gauge Mikrotest 6 G Elektrophysik Germany
Application
Micro Test for every application the Balance measuring system ensures accurate readings at any angle
Horizontal, vertical, overhaead
The gauge allows measurements on curved surfaces
Precise measurements in tubes and on round parts due to the automatic operation.
Measuring Principle
The measurement of the coating thickness is based on magnetic attraction. The attractive force is related to the distance between a permanent magnet and a steel substrate. This distance represents the thickness of the coating to the measured. The magnet is lifted from the surface be means of a spring connected to the magnet arm. The force needed to lift the magnet is directly related to the angle of rotation of the torsion spring. This measuring principle is also especially suited for electroplated nickel on copper, aluminium and other non ferrous metals.
Technical Data
Feature to make your quality control more precise and accurate
Highest accuracy with simplest operation
No calibration necessary simple set up and measurement
All gauges are without power or battery.
One point measurement
Robust metal case to protect from mechanical shocks
Precision measuring system resistant to solvents.
| Type
|
Range in Microns | Application | Tolerance | Minumum
Surface |
Minimum curature
Radius of the sample |
Min. Base Thickness |
| 6 G | 0-100 µm | Electroplating & Paint Coating on Steel |
± 1 µm or 5% of reading | Ø 20mm | 5mm Convex / 25 mm Concave | 0.5mm |
| 6 F | 0-1000 µm | Paint on Steel | ± 5 µm or 5% of reading | Ø 30mm | 8mm Convex / 25 mm Concave | 0.5mm |
| NiFe 50
|
0-50 µm | Electroplating nickel on Steel | ± (2 µm or 8% of reading) | Ø 20mm | 10mm Convex / 25 mm Concave | 0.5mm |
Features:
Following are some of unique features of dual magnetization yoke:
The portable MPI units offered by us are intricately designed for continuous operation and efficiently yields accurate results. Based on latest technology, our units are available in various models.
Our immense industrial expertise and sophisticated machinery aid us in manufacturing and exporting an exclusive array of magnetic particle testing accessories. These are stringently checked by our team of quality controllers and are available in customized ranges. Below Mention All magnetic particle testing (NDT) accessories.
Our range of magnetic particles accessories bears the following varieties:
ZL-27As formulation has been designed to be impervious to water to protect it from over washing and permit more penetrant to remain in discontinuities for improved detection of small defects. It and other post emulsifiable penetrants require the application of a lipophilic or hydrophilic emulsifier to render them washable with water.
ZygloZL-27A fluoresces a bright greenish-yellow under ultraviolet radiation. Use of an ultraviolet light source with a peak wavelength of 365 nanometers, such as the MAGNAFLUXZB-100F fan-cooled black light, is recommended.
ZygloZL-27A penetrant meets OSHA requirements for Class III B liquids due to its high flash point and can be used in open dip tanks.
Applications:ZygloZL-27A is typically used on castings, forgings, extrusions and rough and machined surfaces to find cracks, seams, laps, laminations and porosity.
Classification:Type 1, Method B Penetrant when using ZE-4E emulsifier. Type 1, Method D Penetrant when using ZR-10B (20%) remover.
Meticulously designed, our dual magnetization yoke and portable MPI unit (AC / HWDC Yoke) and MPI Portable Unit are high in performance and are easy to operate. With strong and rugged construction, these are suitable for continuous operation.
Following are some of unique features of dual magnetization yoke:The portable MPI units offered by us are intricately designed for continuous operation and efficiently yields accurate results. Based on latest technology, our units are available in various models.
Some of the technical specifications of our range encompass of the following:
Specifications of portable MPI units:Our immense industrial expertise and sophisticated machinery aid us in manufacturing and exporting an exclusive array of magnetic particle testing accessories. These are stringently checked by our team of quality controllers and are available in customized ranges. Below Mention All magnetic particle testing (NDT) accessories.
Our range of magnetic particles accessories bears the following varieties:
Specifications Compliance:
ASME B & PV Code, Sec. V, ASTM E 709 (E-138), ASTM E 1444, AMS 3042, MIL-STD-271, MIL-STD-2132, NAVSEA 250-1500-1
Part Number and Container Size:
Applications:Magnavis7C Black Visible Wet Method Dry Powder Concentrate is used to locate inclusions, seams, shrink cracks, tears, laps, flakes, welding defects, grinding cracks, quenching cracks and fatigue cracks.
We are offering a precision engineered range of ultrasonic probes, cables and blocks that is manufactured using high grade SS and die cast housings. These are available in varied sizes, designs as per the requirements of our clients and our range of product also includes non destructive testing instrument, dual magnetization yoke. Our range can bear outstanding features and is rigorously checked for high performance, durability, reliability and easy operation standards. Moreover, with special attachments for Indian railways for axle testing, we also offer optional test certificate. We offer varieties of ultrasonic probes, such as Normal Probe, Angle Probe and T-R probe.
Ultrasonic Test Block
tem Code:BAKER
We are authorised dealer for baker items
We have 150mm, 200mm, 300mm 500mm digital , dial and plain verniar caliper.
We have all sizes of micrometers, dial indicators, lever dials, dialthickness gauges
We have ready stock baker hip thread plug and ring gauges.
We are largest seller of gujarat baker measuring instruments
We have authorised dealer and service centre for baker products in gujarat.
Baker give 6month warrantee against mfg. Dfects all product.
|
|
|
|
| Code | Range | Size | Accuracy |
| 821-008-01 | 0 – 360° | 200mm | ±0.3° |
| 821-012-01 | 0 – 360° | 300mm | ±0.3° |
|
|
|
|
|
|
| Code | Range | Resolution | Accuracy |
| 725-360-01 | 0 – 360°ï¼ˆ90°x4） | 0.1° | ± 0.2° |
MagnavisWCP-2 is composed of acetone and inorganic pigments and utilizes a carbon dioxide aerosol propellant for ease of application.
Specifications Compliance:
BS 5044
Part Number and ContainerSize:
Applications:WCP-2 is designed for use in applications where the contrast in color between the part being tested and the magnetic particles being used is insufficient for reliable identification of flaws. WCP-2 can be used with both dry and wet-method magnetic particles.
