Write a Review
Our Products
Our product range contains a wide range of BEAM DEFLECTION SETUP, Beam Test Setup, Single Cylinder, WHIRLING SHAFT and GEAR TRAIN APPARATUS
In a rotating shaft at which instability occurs is called whirling or critical speed. When shaft reaches critical speed it will have maximum deflection. It is applicable in power transmitting equipments like turbine, propeller shafts, etc.
Product Code :SAMS DYN - 004
Gear Train is any combination of gear wheels by which motion is transmitted from one shaft to another shaft. In epicyclic gear trains, the axes of shafts on which the gears are mounted may move relative to a fixed axis.
Product Code :SAMS DYN - 019
The apparatus consists of a pad, which can be tilted to the required angle. An endless belt, which moves beneath the pad, carries the oil over its surface from oil bath. When the pad is tilted over the oil film, pressure is developed, the pad is provided with pressure tapings parallel and perpendicular to belt direction. The pressure distribution is measured over a multi tube manometer. The belt is driven by a variable speed motor. The tilting angle and minimum gap between pad and belt can be adjusted and characteristics thus can be studied at various gaps, inclination and relative surface speeds.
Product Code :SAMS DYN - 020
The apparatus is designed to help in conducting various experiments to illustrate and verify the principles and relations involved in the study of vibrations. Following experiments can be performed with this unit.
Product Code :SAMS DYN - 029
A bench mounted beam apparatus to allow students to investigate the deflections and reactions in simply supported and cantilevered beams
Product Code : SAMS AE - 003
The unit uses water as the flow medium. A contrast medium (dye) is injected through small needles into the flow area. Various drag bodies (included) can be placed in the area of flow. In addition, sources and sinks can be simulated and illustrated using eight additional openings in the flow area.
Product Code : SAMS AE - 006
SAMS Los Angles Abrasion Machine is used for determining are resistance to bear of small size Course Aggregate and Crushed rock The machine consistence of a hollow cylinder mounted one sturdy frame on ball bearings a detachable shelf which extends which stand through out the inside length of the drum catches the abrasive charge and dose not allow its two fall on the cover the drum is rotated at a speed of 30-33 RPM by an electric motor through a heavy duty reduction gear motor is suitable for operation on 220 Volts-50Hz- 1p.h.
Product Code : SAMS CVL - 014
To carry out the following experiments
Performance Test
Heat Balance Test
Retardation Test
Product Code : SAMS THR - 002
The apparatus consists of stainless steel bath and universal and furol jets of stainless steel stirring is done manually with turn table arrangement.
Product Code : SAMS FTL - 003
For determining closed cup flash point of petroleum products, their mixtures, other liquid and paints, having flash points between 19 C and 49 C. Each apparatus is supplied complete with an oil cup, cover fitted with gas test jet assembly, water bath and tripod stand, but without thermometer, in a wooden carrying case.
Product Code : SAMS FTL - 006
Tar viscometer apparatus as per IP-72 and IS 1206 standards. It is used for determination the viscosity of road oils and cut back bitumen. It consists s. S. Bath with cup of 10 mm or 4 mm orifice and sleeve, stirrer with lifting clip and ball. The assembly kept on suitable stand with leveling screws. Suitable to operate on 220 volts ac mains.
Product Code : SAMS FTL - 009
Specification : This measuring machine is designed to have accurate measurements of major, minor & effecive diameter of precision screw threads as well
Torque Cell : 1 kg-m capacity
Loading : L angle and 1 m length fulcrum arm
Weights : 100gms x10 nos
Product Code : SAMS MTR - 002
Specification : Operates on the principal of the Change of inductance of a coil by movement of a steel armature, which is moved by a plunger arrangement in contact with the surface to be checked. the plunger consists of Electrical Gauge Head with armature and feeler, Ammeter, Power Supply, with 2 amps x 2 Nos. dimmer & specimen Holder
Product Code : SAMS MTR - 009
Our firm delivers precisely tested and a high-grade assortment of Headlight Beam Aligner
Product Code : SAMS AUTO - 008
World wide basemap
2.2 monochrome display, easy to read in any light
GPS and GLONASS satellites for faster positioning
Paperless geocaching
Strain Measurement Module comprises of Cantilever Beam bonded with four strain gauges, pan and weights upto 1Kg. Digital 3 digit indicator module is supplied to read the microstrain.
SAMS Engineering (SAMS Engineering)
NO 17 Lakshmi Street, Jafferkhanpet, - 600083, Chennai, Tamil Nadu, India
Share us via
