Transformers also provide an extremely useful feature called isolation, which is the ability to couple one circuit to another without the use of direct wire connections. There are applications where electrical isolation is needed between two AC circuits without any transformation of voltage or current levels. In these instances, transformers called isolation transformers having 1:1 transformation ratios are used.

Our Isolation Transformers isolate the equipments from noisy power line hence providing a better option to clients. These remove power line noise, surges, spikes and transients. It also provides high insulation resistance and provides complete electromagnetic and electrostatic shielding.

Our range of Isolation Transformers is designed as per the international standards which give an assurance to the customer on the high quality of the product. An isolation transformer does not have a direct electrical path from the power input side to the power output side. The term is also used to define how much electrical isolation exists between the input and output windings. For example when using line-voltage input transformers to power low voltage device handled by humans, a high degree of isolation is required for safety. Isolated transformers often use separate bobbins for the primary and secondary coil windings, but usually the windings are just wound on top of each other with insulation in between. There is usually an electrostatic shield between windings which is tied to transformer case.

We offer high quality Step Down Transformers. It is hard wired, durable with a heavy duty chord. It has a 100 Watt maximum capacity and can be used continuously over a period of time. It has one grounded outlet in front of unit (accepts 3 or 2 prong US and Euro plugs) and reduces the voltage to the fit the next level of desired use. Perhaps it will go to some point in a factory, shop, home or even the much smaller applications and be reduced again to fit a lower voltage piece of equipment.

Step Down Transformers have a primary winding of higher number of turns than the secondary winding. Since power is fixed, lowered voltage results in increased amperage; the lowering of voltage is inversely proportional and results in increase of amperage. Our Step Down Transformers are relatively simple in design and they have the exact ratio of windings in each circuit so as to deliver the appropriate current and voltage. Application, budget and other factors must be considered before installing a particular transformer. Both incoming and outgoing voltages must be known prior to selecting any Step Down Transformer.

We offer all our products as per ISI specifications which give an assurance to the customer on the quality of our product. We are equipped with an R&D unit and testing tools and section which has got all tools and testing facilities that support us in supplying products as per clients specific requirement.

• 1KVA to 300KVA maximum capacity heavy-duty continuous use transformer
• One grounded outlet in front of unit (accepts 3 or 2 prong US and Euro plugs)
• Hard wired
• Durable design with a heavy-duty cord

We supply a gamut of Buck-Boost Transformer that is widely used in Servo Stabilizers and can be customized as per the specific requirements of our clients. These boost transformers are made in compliance of necessary standards. Some of boost transformers features are:

• Highly durable
• Saves energy cost
• Cost effective

Buck Boost devices are used to make small adjustments to incoming voltages such as lighting applications.

We offer high grade buck-boost converter coils, which are manufactured using excellent quality materials to last for a long period of time. We pack these buck-boost converter coils in appropriate packaging for their safe delivery to our clients. Our dexterity lies in developing them as per the specifications of our clients.

Transformers also provide an extremely useful feature called isolation, which is the ability to couple one circuit to another without the use of direct wire connections. There are applications where electrical isolation is needed between two AC circuits without any transformation of voltage or current levels. In these instances, transformers called isolation transformers having 1:1 transformation ratios are used.

Our Isolation Transformers isolate the equipments from noisy power line hence providing a better option to clients. These remove power line noise, surges, spikes and transients. It also provides high insulation resistance and provides complete electromagnetic and electrostatic shielding.

Our range of Isolation Transformers is designed as per the international standards which give an assurance to the customer on the high quality of the product. An isolation transformer does not have a direct electrical path from the power input side to the power output side. The term is also used to define how much electrical isolation exists between the input and output windings. For example when using line-voltage input transformers to power low voltage device handled by humans, a high degree of isolation is required for safety. Isolated transformers often use separate bobbins for the primary and secondary coil windings, but usually the windings are just wound on top of each other with insulation in between. There is usually an electrostatic shield between windings which is tied to transformer case.

We offer high quality Step Down Transformers. It is hard wired, durable with a heavy duty chord. It has a 100 Watt maximum capacity and can be used continuously over a period of time. It has one grounded outlet in front of unit (accepts 3 or 2 prong US and Euro plugs) and reduces the voltage to the fit the next level of desired use. Perhaps it will go to some point in a factory, shop, home or even the much smaller applications and be reduced again to fit a lower voltage piece of equipment.

Step Down Transformers have a primary winding of higher number of turns than the secondary winding. Since power is fixed, lowered voltage results in increased amperage; the lowering of voltage is inversely proportional and results in increase of amperage. Our Step Down Transformers are relatively simple in design and they have the exact ratio of windings in each circuit so as to deliver the appropriate current and voltage. Application, budget and other factors must be considered before installing a particular transformer. Both incoming and outgoing voltages must be known prior to selecting any Step Down Transformer.

We offer all our products as per ISI specifications which give an assurance to the customer on the quality of our product. We are equipped with an R&D unit and testing tools and section which has got all tools and testing facilities that support us in supplying products as per clients specific requirement.

• 1KVA to 300KVA maximum capacity heavy-duty continuous use transformer
• One grounded outlet in front of unit (accepts 3 or 2 prong US and Euro plugs)
• Hard wired
• Durable design with a heavy-duty cord

We supply a gamut of Buck-Boost Transformer that is widely used in Servo Stabilizers and can be customized as per the specific requirements of our clients. These boost transformers are made in compliance of necessary standards. Some of boost transformers features are:

• Highly durable
• Saves energy cost
• Cost effective

Buck Boost devices are used to make small adjustments to incoming voltages such as lighting applications.

We offer high grade buck-boost converter coils, which are manufactured using excellent quality materials to last for a long period of time. We pack these buck-boost converter coils in appropriate packaging for their safe delivery to our clients. Our dexterity lies in developing them as per the specifications of our clients.