Ambala, Haryana, India
Verified
Add Review
Our Product / Services
Glass, with moulded cover to take upto 10 slides, back toback.
Coplin Jar made of Polypropylene can hold 10 slides of the size 1x3 back to back. The interior of the Coplin Jar is grooved in a way to hold slides in erect position. Domed & shallow thread screw cap provides protection to the slides.
Material:
Polypropylene
Beakers, Moulded In Polypropylene, Have Excellent Clearity And Very Good Chemical Resistance. These Autoclave Beakers Have Prominently Raised Graduations On The Outer Surface. Pouring A Solution Becomes Very Convenient Because Of Its Tapered Spout. Material: Polypropylene.
Elisa/Assay Plates Are Made Of Optically Clear, Non-Toxic Polystyrene. These Plates With 96 U Bottom Or Flat Bottom Wells Bear Alpha-Numeric Index. Uniform Placement Of All The Wells Facilitate Use Of Multi Channel Pipettes. These Plates Packed Individually Are Available Non-Sterile As Well As Radiation Sterilized
Material:
Polyethylene
This Non-Toxic Disposable Loop Is Accurate To Semi Quantitative Stand For Handling Samples.
Material:
Polystyrene
These Transparent Specimen Jar, Used Preserving Different Specimens In The Lab Are Provided With A Cap That Fits In Tight.These Jars Provided Excellent Protection To The Speciespreserved In It.
Material:
Polystyrene
This Ingenious Racks With A 3 Tier Design Provide Clear View Of The Tube Contents And Convenient Insertions And Renoval Of Tubes. The Pc Rack Has Transparent Upper And Middle Plates Where As In Pp Racks, Every Parts Is Coloured And Opaque. These Autoclavable Racks Can Withstand Sub-Freezing Temperatures.
Material:
Polycarbonate
Separatory Funnel Is Made Of Polypropylene, Giving It Excellent Contact Clarity And Strength. This Pear Shaped, Autoclavable Separating Funnel Has A Leakproof Threaded Screw Cap. The Polypropylene Stopcock, Fitted With A Self Lubricating Ptfe Plug, Is Push Fitted To The Stem Of The Separatory Funnel
Material:
Polypropylene
Adding In Line Of Aspirators, These Polypropylene Carboys Are Autoclavable, Dependable & Durable. These Are Also Equipped With A Leakproof Spigot Screwed To The Body. These Carboys Are In Excellent Replacement For Glass Carboys And Are Used For Storing & Dispensing Distilled Water & Other Laboratory Solutions.
Material:
Polypropylene
These Transparent, Ready To Use, Disposable Petri Dishes Are Made Of Optically Clear, Non-Toxic, Polystyrene. These Petri Dishes Packed Individually In Polyethylene Bags Are Sterilized By Radiation.
Material:
Polystyrene
Elisa/Assay plates made of optically clear non-toxic polystrene for a wide range of applications from single cell isolation to cell culture scale up, with 96 wells
This Set Consists Of Moulded Balls Of Different Colours & Sizes Alongwith Connectors Of Different Sizes. The Sizes & Shapes Of The Balls & Connecting Lugs Have Been Designed In Accordancewith Internationally Acceptable Standards.
Material:
Polystyrene
Moulded in Polypropylene, this staining box helps in staining, fixing, de-staining and handling fragile electrophoresis gels and membranes. Box as well as cover will resist temperatures from 70C to +70C. The LDPE plug provides leakproof seal and allows easy liquid drainage.
Material:
Polypropylene
Needless To Say, Polypropylene Laboratory Tray Moulded In Polypropylene Is A Multipurpose Tray That Can Be Used For Sterilizing, Drying Glassware Porcelainware & Other Laboratory Instruments. These Steam Autoclavable Trays Have Tapered Walls Which Prove Good For Nesting.
Material:
Polypropylene
A Handy, Little, Space Saver, This Circular Twelve Place Polypropylene Test Tube Stand Has Four 25 Mm Dia Holes & Eight 19Mm Dia Holes In Its Top Plate. The Base Has Matching Hemispherical Wells & 16 Vertical Pins For Drying Tubes Surrounded By A Trough To Catch Drippings. This Autoclaveable Rack Can Be Easily Disassembled For Cleaning Purpose.
Material:
Polypropylene
These Desiccators Are Made Of Polypropylene And Polycarbonate. These Autoclavable Vaccum Desiccators Can Hold Vaccum Upto 740Mm Of Hg For 24 Hrs. Without Any Greasing.The Top Dome, Moulded In Rigid And Transparent Polycarbonate, Gives A Crystal Clear View Of The Desiccant Placed Inside.The Knurled Knob On The Top Provides Easy Handling Of The Dome.The Lower Part Is Made Of Polypropylene.An Internal Groove Is Provided On The Flange To Hold A Silicon Rubber Oringthe Polypropylene Stopcock Is Fitted With A Self Lubricating Ptfe Plug.This Plug Works Three Way I.E. Vaccum Creation, Shutting Off & Vaccum Releasing.
Material:
Polypropylene / Polycarbonate
Moulded In Polypropylene, This Flask Stand Gives A Stair-Like Top View. Every Step Provides Excellent Support To The Round Bottom Flask At Every Point Of Contact. This Flask Stand Can Hold Round Bottom Flasks Upto 10 Ltrs. Capacity. This Stackable Flasks Can Also Be Steam Autoclaved.
Material:
Polypropylene
Die Casted Alloy, accepts article square and round section upto 16 mm diameter at right angle to each other. Can also hold flat articles such as drawing board, magnets, rulers etc
Plain Desiccators Are Physically The Same As Vaccum Dessiccator. Only Difference Is The Absence Of Stop Cock. Grease Should Be Applied On The Flanges To Make It Air Tight.
Material:
Polypropylene / Polycarbonate
Simple Cell Pot, As The Name Suggests, Is Used For Making Simple Cell & Voltmeters Etc. Moulded In Polypropylene, This Pot Has Very Good Contact Clarity And Excellent Chemical Resistance. Being In Polypropylene, This Pot Is Much Durable Than The One Use Conventionally.
Material:
Polypropylene
Measuring Cylinders, Moulded In Polypropylene & Tpx, Are Single Piece Cylinders. These Autoclavable Cylinders Have Raised Prominent Graduations For Easy Reading And Have Excellent Contact Clarity. The Broad Base Provides Good Stability.
Material:
Polypropylene
Blown In Polypropylene, This Pot Is Used For Making Leclanche Cell .This Pot Too Has Good Contact Clarity & Excellent Chemical Resistance.
Material:
Polypropylene
These Desiccators are made of Polypropylene and Polycarbonate. These autoclavable vacuum desiccators can hold vacuum upto 740mm of Hg for 24 hrs. without any greasing. The top dome, moulded in rigid and transparent Polycarbonate, gives a crystal clear view of the desiccant placed inside. The knurled knob on the top provides easy handling of the dome. The lower part is made of Polypropylene. An internal groove is provided on the flange to hold a silicon rubber O-Ring. The Polypropylene stopcock is fitted with a self lubricating PTFE plug. This plug works three way i.e. vacuum creation, shutting off & vacuum releasing.
These Vacuum Desiccators are provided with a transparent polycabonate bottom that makes it more robust and provides excellent view of the desiccator. All the other features are same as PP/PC vacuum desiccators.
Plain Desiccators are physically the same as Vacuum Dessiccator. Only difference is the absence of stop cock. Grease should be applied on the flanges to make it air tight.
Wood, with steel spring for closing jaws, length 180 mm approx for 11-19 mm diam. tubes.
Stout brass strips mounted in wooden handle to hold tubes from 12 mm to 40 mm. Overall length 220 mm.
Stainless steel, jaws covered with asbestos, can firmly hold any beaker from 250 ml to 1000 ml.
For hot beakers from 100 to 1500 ml capacity. Stainless steel with riveted joint and fiberglass-covered jaws. Length : 12 ?.
Nickel-plated steel. Long and rigid for furnace use. With large handles and serrated tips. Total length: 18 ?.
Disposable, clear polystyrene, supplied in sterilized pack
Clear acrylic with polycarbonate posts. Useful during inoculation, incubation & storage. Visibility from all sides enables the culture to be seen & check during incubation.
Circular twelve place Polypropylene Test Tube Stand has four 25 mm dia holes & eight 19mm dia holes in its top plate. The base has matching hemispherical wells & 16 vertical pins for drying tubes surrounded by a trough to catch drippings. This autoclave able rack can be easily disassembled for cleaning purpose
3 tier design provide clear view of the tube contents and convenient insertions and removal of tubes. These autoclavable racks can withstand sub-freezing temperatures.
Material : Polypropylene
An economical substitute for wire racks, here are these submersible, autoclavable racks which are stackable when empty. These are available in different colors and are made of a special blend of polypropylene that makes it sink in a water bath and maintain their stability even in agitated water. These space saving racks can easily be disassembled for cleaning purposes. The base is in the form of a grid with square openings and has fold up sides and end bars that lock into rack tops.
12 holes in two rows for tubes up to 25 mm in dia and 12 draining pins.
Strongly constructed, with 12 holes in one row and 12 draining pins. Ten holes accommodate tubes up to 25 mm in dia.
Steel base with tapped hole, (10 x 1.5 mm metric thread) in the center of one short side. Finished in blue and fitted with rubber feet.
With an adjustable holder swivel at the centre to fix boss head at any angle. Can hold rods up to 16 mm diameter.
