Aroha Altimate Ply is the alternate plywood composed with alternate core veneers of Red Core and Poplar. It is available in Moisture Resistant (IS:303) and Boiling Water Resistant (IS:710) grades. MR grade is made with Melamine fortified Urea formaldehyde resin and BWR grade is made with undiluted Phenol formaldehyde resin. Both the grades are used for the interior and exterior woodworking application. Aroha Altimate Ply is manufactured under controlled temperature and pressure with adequate timing to obtain unmatched bonding. Both the grades are manufactured in country's best hydraulic hot press with higher density as compared to other plywoods available, which reduces water absorption thereby removing warping, swelling and de-lamination. Finally the ply is tested in fully equipped laboratory for stringent quality controls with trained personnel. Aroha Altimate Ply is composed using 8 x 2 ft full core panels to ensure zero gaps, zero overlaps, zero splitting as well as strong screw & nail holding capability. More plies are used to render the plywood bend resistant and warp proof. Last but not the least; it is made resistant to borers, termites and other wood destroying insects. Thickness available:  6mm, 9mm, 12mm, 15mm, 18mm and 19mm. Suggested Uses:  Ceilings, door panel inserts, vehicle seats and backs, floor underlay, kitchen furniture, bedrooms, partitions, furniture like chair, study table, dining table, drawers, shelves, racks, cupboards, showcases, etc.

Aroha Rigid ply is composed with 100% red core high quality veneers. Each and every panel is made with pre-press technology and is bonded at high pressure and temperature with undiluted Phenol formaldehyde resin. It is further treated in a vacuum pressure impregnation plant, using specific preservative to render it resistant to marine organisms. Aroha Rigid Ply panels are composed using 8×2 core panels of thickness 1.8mm for each layer of core. This ensures that the finished ply has zero core gaps, zero overlaps and zero splitting on nailing or cutting. The panels are finished with 0.4mm thick Gurjan face veneer. It can withstand rigorous climatic conditions, alternate dry and wet weather in deep sea. Avron Marine Plywood is made to be warp free, bend resistant and maintain its structural integrity for its lifetime. And that is precisely why we stand committed behind every panel with a Lifetime Warranty on our Aroha Rigid Marine Ply. Sizes available:  6mm, 9mm, 12mm, 16mm, 19mm Suggested Uses:  It is ideal for exterior applications like construction and repair of boats, bus and truck bodies, cooling towers, kitchen cabinets, signboards, false ceilings, speaker cabinets, portable cabins and shelters exposed to weather extremities, structural applications and premium Interiors & Exteriors applications.

Aroha Pinnacle Block Boards are manufactured from the combination of selected, seasoned, durable Pine wood . These are bonded with Melamine fortified Urea Formaldehyde Resin under high pressure and temperature for MR grade and Phenol Formaldehyde resin for BWP grade. The block boards are resistant to twisting /warping, have superb screw holding and nail holding capability. This is mainly possible because of seasoned and durable Pine wood timber. All the three components of this block board i.e. face veneer, core veneer and wooden battens are well matched. The wooden battens are thoroughly seasoned in scientifically run seasoning kiln plants and then cut with great precision to obtain uniform thickness. These battens are systematically arranged and utmost care is taken to avoid any extra gap between the battens. Core veneer, battens and frames are well treated before use to make them resistant against termite and borer attack. Regular tests are conducted to maintain the quality of block boards as per the standards of IS:1659.  Ideal for wardrobes, cabinet doors, beds, partitions, shutters etc.

Aroha flush doors (IS:2202) are ready to use and can be mounted easily with minimum efforts to beautify your dream home. Aroha flush doors are manufactured under strict quality control conditions that fully comply with the ISI specifications. The chemically treated battens and frames of Aroha waterproof flush doors prevent any attack of micro-organisms, borer, termite, fungus or any rot. These are well finished flush doors with smooth surface for laminations. They offer dimensional accuracy and stability in varying humidity and have a high screw holding capacity, high shock and buckling resistance. Three inches wide hardwood frames are sandwiched between PF glued veneers which are pressed at a very high temperature and pressure. The timber battens are tightly filled in those frames to make them very sturdy and durable. They have high load bearing capacity making them dimensionally stable.

Aroha Film faced shuttering ply (IS:4990) is manufactured from superior quality hardwood procured from the reliable vendors. The panels are composed by aligning several layers of phenolic resin-coated veneers, each placed at right angles to each other. Here we compress them 60% as compared to any other shuttering ply available in the market. Extra compression leads to better nail and screw holding capacity. By using selected quality veneer (impregnated with modified RPF resin) longer life and better quality is guaranteed. Top film on either side is backed by a highly absorbent kraft sheet which increases abrasion-resitant and water resistant properties. Aroha Shuttering Ply possesses balanced construction both parallel and perpendicular to the panel with equal strength in both directions. The phenolic layer is free from dents or pitches on the surface and thus possess a mirror-like finish which imparts a smooth surface to concrete structures. The ply is non-corrosive and can withstand a high alkaline medium with cement concrete. Aroha Film-Faced Shuttering Ply maintains unchanged technical characteristics throughout the whole period of use which results in more repetitions than conventional plywoods, thus increasing the value for money of the plywood. Used for formwork in the construction of flyovers, bridges, tunnels, multi-storied high rises, concrete moulds and precasts.  

Aroha Altimate Ply is the alternate plywood composed with alternate core veneers of Red Core and Poplar. It is available in Moisture Resistant (IS:303) and Boiling Water Resistant (IS:710) grades. MR grade is made with Melamine fortified Urea formaldehyde resin and BWR grade is made with undiluted Phenol formaldehyde resin. Both the grades are used for the interior and exterior woodworking application. Aroha Altimate Ply is manufactured under controlled temperature and pressure with adequate timing to obtain unmatched bonding. Both the grades are manufactured in country's best hydraulic hot press with higher density as compared to other plywoods available, which reduces water absorption thereby removing warping, swelling and de-lamination. Finally the ply is tested in fully equipped laboratory for stringent quality controls with trained personnel. Aroha Altimate Ply is composed using 8 x 2 ft full core panels to ensure zero gaps, zero overlaps, zero splitting as well as strong screw & nail holding capability. More plies are used to render the plywood bend resistant and warp proof. Last but not the least; it is made resistant to borers, termites and other wood destroying insects. Thickness available:  6mm, 9mm, 12mm, 15mm, 18mm and 19mm. Suggested Uses:  Ceilings, door panel inserts, vehicle seats and backs, floor underlay, kitchen furniture, bedrooms, partitions, furniture like chair, study table, dining table, drawers, shelves, racks, cupboards, showcases, etc.

Aroha Rigid ply is composed with 100% red core high quality veneers. Each and every panel is made with pre-press technology and is bonded at high pressure and temperature with undiluted Phenol formaldehyde resin. It is further treated in a vacuum pressure impregnation plant, using specific preservative to render it resistant to marine organisms. Aroha Rigid Ply panels are composed using 8×2 core panels of thickness 1.8mm for each layer of core. This ensures that the finished ply has zero core gaps, zero overlaps and zero splitting on nailing or cutting. The panels are finished with 0.4mm thick Gurjan face veneer. It can withstand rigorous climatic conditions, alternate dry and wet weather in deep sea. Avron Marine Plywood is made to be warp free, bend resistant and maintain its structural integrity for its lifetime. And that is precisely why we stand committed behind every panel with a Lifetime Warranty on our Aroha Rigid Marine Ply. Sizes available:  6mm, 9mm, 12mm, 16mm, 19mm Suggested Uses:  It is ideal for exterior applications like construction and repair of boats, bus and truck bodies, cooling towers, kitchen cabinets, signboards, false ceilings, speaker cabinets, portable cabins and shelters exposed to weather extremities, structural applications and premium Interiors & Exteriors applications.

Aroha Pinnacle Block Boards are manufactured from the combination of selected, seasoned, durable Pine wood . These are bonded with Melamine fortified Urea Formaldehyde Resin under high pressure and temperature for MR grade and Phenol Formaldehyde resin for BWP grade. The block boards are resistant to twisting /warping, have superb screw holding and nail holding capability. This is mainly possible because of seasoned and durable Pine wood timber. All the three components of this block board i.e. face veneer, core veneer and wooden battens are well matched. The wooden battens are thoroughly seasoned in scientifically run seasoning kiln plants and then cut with great precision to obtain uniform thickness. These battens are systematically arranged and utmost care is taken to avoid any extra gap between the battens. Core veneer, battens and frames are well treated before use to make them resistant against termite and borer attack. Regular tests are conducted to maintain the quality of block boards as per the standards of IS:1659.  Ideal for wardrobes, cabinet doors, beds, partitions, shutters etc.

Aroha flush doors (IS:2202) are ready to use and can be mounted easily with minimum efforts to beautify your dream home. Aroha flush doors are manufactured under strict quality control conditions that fully comply with the ISI specifications. The chemically treated battens and frames of Aroha waterproof flush doors prevent any attack of micro-organisms, borer, termite, fungus or any rot. These are well finished flush doors with smooth surface for laminations. They offer dimensional accuracy and stability in varying humidity and have a high screw holding capacity, high shock and buckling resistance. Three inches wide hardwood frames are sandwiched between PF glued veneers which are pressed at a very high temperature and pressure. The timber battens are tightly filled in those frames to make them very sturdy and durable. They have high load bearing capacity making them dimensionally stable.

Aroha Film faced shuttering ply (IS:4990) is manufactured from superior quality hardwood procured from the reliable vendors. The panels are composed by aligning several layers of phenolic resin-coated veneers, each placed at right angles to each other. Here we compress them 60% as compared to any other shuttering ply available in the market. Extra compression leads to better nail and screw holding capacity. By using selected quality veneer (impregnated with modified RPF resin) longer life and better quality is guaranteed. Top film on either side is backed by a highly absorbent kraft sheet which increases abrasion-resitant and water resistant properties. Aroha Shuttering Ply possesses balanced construction both parallel and perpendicular to the panel with equal strength in both directions. The phenolic layer is free from dents or pitches on the surface and thus possess a mirror-like finish which imparts a smooth surface to concrete structures. The ply is non-corrosive and can withstand a high alkaline medium with cement concrete. Aroha Film-Faced Shuttering Ply maintains unchanged technical characteristics throughout the whole period of use which results in more repetitions than conventional plywoods, thus increasing the value for money of the plywood. Used for formwork in the construction of flyovers, bridges, tunnels, multi-storied high rises, concrete moulds and precasts.