Sidharatha Equipments

GIDC, Mahesana, Gujarat

• variation in the spreading width can be achieved infinitely, from zero to maximum, by use of a lever controlled taper door control of the desired coverage is by a screw adjusted rubber gate mounted above the feed roller. Large foreign bodies pass through without causing damage. A metered application results by using spring loaded drive wheel, that automatically contacts the road surface as the body is tipped to the working position, and rotates the feed roller relative to ground speed through an operator controlled dog clutch. The main body design now incorporates a large throat with an adjustable battle to suit the different flow characteristics of the material to be spread. To further assist the flow and to material to be spread. To further assist the flow and to break up lumps of coated chippings, an optional agitator is available for fitting in the throat. when required a full width operator platform can be specified as an optional extra. This allows the operator to ride with the machine and operate the controls in greater safety. specification
• weight of 2.25 m model - 650 kg. (approx).
• weight of 2.2 m model - 700 kg. (approx). bodyconstructed form 4mm pressed steel plate with hollow square and rectangular reinforcing cestions and channels. feed rollerserrated surface feed roller constructed from 165 mm (11/2") diameter tube mounted between self aligning lubricated for life bearings. baffle(to control material surge) bolt on variaable position battle plate. adjustable from 100 mm to 250 mm in 50 mm increments. feedgateadjustable gate with hand operated adjusting screws. Bottom section of gale in rubber to permit passage of oversize objects without damage. note: for possible applications other than surface dressing the gate is removable.
• feed opening: 50mm(2")
• feed gate fitted: 75mm(3") feed remove cut off door (width of spread)infinitely adjustable from zero to maximum by lever controlled taper door, when baffle is either of its two lowest settings. When the baffles are in the two highest settings and depending on the material being spread, the cut off minimum width will vary. drivea 457 mm x 178 mm (24" x 7") pneumatic tyred wheel tansmits drive from the road surface through a 19 mm (3/4") chain drive from the road surface through a 19 mm (3/4") chain drive to a cast iron / m.s dog clutch. Mounted on a lay shaft. The drive is then transmitted through this shafts to a chain drive fitted to the feed roller. All shafts are mounted on self aligning, self lubricating ball bearings, with the clutch operated by levers either side of the unit. The roller chain drive is fully enclosed in a heavy duty guard designed to self clean. The drive wheel position is adjustable to suit truck bed heights down to 1100mm (43") optional extras platformplatform with stand rails and across step either side. Weight 77 kg. (170lbs) agitatorsheavy duty tube with high tensile tongues, mounted in self aligning, self lubricated bearings. Chain drive from existing roller drive. Weight 11 kg. (24lbs)(approx). scatter platea quick reales unit designed to exrend the existing width of spread uniformly by 0.5 (20") setting angle variable to suit chipping size and flow characteristics. For travelling the scatter plate the scatter plate ends can be foled in to reduce the machines overall width.weight 55kg. (121 ibs) (approx)

WATER TANKOne / Two Water Tanks of 15 / 20 MT capacity each are provided, fabricated from steel plates with manhole, flowmeter, pump etc. CONTROL CABIN A fully automatic Control Panel is provided for controlling the quantity and quality of production with operator sitting in Air-conditioned comfort. MINERAL FILLER Fabricated from steel plates, it feeds the required quantity of additives to the pug mill. OPTIONALVariable Feeding Device can be provided for Belt Feeder. Wet Mix Storage Silo.

which can be opened in any position to regulate the aggregate flow. Individual endless belts are provided below the gates to discharge material onto the gathering belt. VIBRATING SCREEN A single-deck vibrating screen is provided on the slinger conveyor to remove oversize aggregate received from the 4-bin feeder. SLINGER CONVEYORAn inclined conveyor mounted on idlers receives aggregate from the gathering conveyor and feeds it to the dryer LOAD OUT CONVEYOR Mixed aggregate from the dryer drum is discharged on an inclined conveyor provided with a hydraulic hopper at delivery end for feeding the Mix into Tippers. BITUMEN TANKS One/Two Bitumen Tanks of 15/20/30 MT capacity each are provided, fabricated from steel plates with 50 mm glasswool insulation, manhole, thermocouples, etc. Bitumen is pumped to the dryer drum through pipe lines. Tanks are fitted with independent on-off type burners. MULTICYCLONE EXHAUSTThe dust collection system consists of enclosed multiple cyclones, exhaust fan and chimney. MINERAL FILLER Fabricated from steel plates, it feeds the required quantity of mineral to the drum. CONTROL CABIN A fully automatic control panel with feather touch controls is provided for controlling the quantity and quality of production with operator sitting in Air-conditioned comfort.All systems are completely synchronized with automatic / manual control of burners, load cells, mix temperature, cold feed / mineral / bitumen proportions, etc. Manual control is possible through over-ride system. Adequate safety measures are adopted to avoid overloading, short-circuit, etc. LDO TANK One LDO Tank of 2000 / 4000 Ltrs. Capacity is provided with each plant. OPTIONALS Wet type air pollution control system. Baghouse filter system.Hot mix storage silo.Portable plants.

Drive wheels1000 X 20 16 ply Front wheelOne Rubber coated steel wheel on each side rubber coated BrakesAir brakes on rear wheels thourth tandem master cylinder assisted by Single chamber air pressure booster, mechanically operated parking brake. Truck push rollerPush roller are adjustable for height and reach. Screed2500 mm width heavy duty having mechanical extension and extendable up to 4000 mm slides over premixed material. HoppersHydraulically operated folding hoppers. FeedersThe Single bar conveyor chain feeds the material from bottom plate 10 mm thick made from wear resistant and heat resistant steel plate. Spreading ScrewMechanically driven 250 mm dia. hard surface welded.