Our Products #389328

We are the worldwide one-stop-shop for all Hydraulic Seals. Our family of Hydraulic Seals provides the optimum sealing solutions for almost every hydraulic application, from the most accurate instruments and control actuators up to the heaviest forging and extrusion presses. For arduous and critical duties, we recommend our Hydraulic Seals for your less demanding roles. Superior quality of Hydraulic Seals will give best value benefits in reduced plant downtime and maintenance costs. Each Hydraulic Seal Has Been Specially Developed And Proven To Give

• Optimum equipment performance
• Reduced leakage
• Low friction operation
• Long trouble-free operating life

Minimum Order Quantity : 5

Axial Plunger Pump is a plunger pump of the rotating swash plate type and is fitted with either three or six plungers. Where six plungers are fitted, they are arranged to discharge in two sets of three. The three plunger model has the plungers spaced in position (A) Section I, Axial Plunger Pumps are identified by size numbers 1, 2 and 4. There is one exception to this rule in the case of the XA4, which is a 6 plunger model, comprising two size 2 sections. For smaller outputs or outputs between these three basic sizes, one or two plungers are rendered inoperative by the size numbers 001' 01, 02 etc. In the first case, two, plungers are inoperative in the others, only one plunger inoperative. The six plunger model has the plungers spaced as Section I. If one set of three plungers is larger than the other, then the larger plungers are spaced in the (A) position, the six plungers model can have all six plungers, combined in a discharge block, fitted to face (X) to discharge through a single part. Axial Plunger Pumps are identified by the size numbers 3, 5 and 6 or in rare cases 2001, 201, 402 etc. If the six plungers are arranged to discharge in two sets of three through two separate parts in the discharge block, they are identified by the numbering 1/2, 2/4, 001/2 etc. It is possible to combine any single output from three rams with any other, but in practice there is little demand for such combinations, and these are subject to additional charge. The Axial Plunger Pumps are fitted with a through shaft so that other low pressure pumps or a second Axial Plunger Pump can be tandem mounted on the outboard end by housing (80). The Axial Plunger Pump Comprises Four Main Assemblies

• The Boost Pump.
• The High Pressure Pump Body
• The Driving Shaft, Wash member and Wobbler Plate Assembly
• The Pump Drive Housing

Minimum Order Quantity : 5

We are Manufacturer of precision engineered Hydraulic Boosting Pump. We have replacement for wide range of reputed makes, like Sandsun, Pascal, Kosmek, Kingair, Konan, Saejin and KAN-TOU. We have Hydraulic Boosting Pump for presses capacity upto 1200 ton. Hydraulic Boosting Pump, available with us, is in extensive demand owing to its reliable performance.

• Overload protector is equipped in press machine to check the hydraulic pressure of cylinder inside the slider.
• If overload happens, the hydraulic pressure of cylinder will be released immediately within 3/1000 seconds.
• When overload happens, in order to protect the press and die, the press will stop working immediately after receiving the signal from limit switch
• After overload happens, the air will drive Hydraulic Boosting Pump to supplement normal working pressure immediately and the press can work normally.
• Hydraulic Boosting Pump has pressure control valve inside of overload protector, which can adjust hydraulic pressure automatically and eliminate the impact of rising pressure (caused by oil temperature rise) in pressing process.

Minimum Order Quantity : 5

In tune with our commitment to adhere to high quality standards, we have gained expertise in the manufacturing Hydraulic Cylinder, under the brand name Precise. The Hydraulic Cylinder ranges from bore 25 x rod 12 x stroke10 mm till bore 330mm x rod 200 x stroke 3000 mm, with working pressure up to 500 Kg/cm². To stick to our high quality standards in Hydraulic Cylinder, we use only imported sealing & guidance systems. All our honed tubes are micro finished to a Ra value less than 0.3 microns. We also supply Hydraulic Cylinder with imported honed tubes to suit our customer requirements. Our piston rods are ground and hard chrome plated. Whether it is the standard tie rod or welded Hydraulic Cylinder or the custom built threaded and block / Clamp Hydraulic Cylinder, we stick to our high quality standards and ensure that only imported sealing and guidance systems are always used. Additionally, our piston rods are ground and hard chrome plated. All this is backed up with a warranty period of 12 months, which is a testimonial to our expertise in the manufacture of hydraulic cylinders. We Manufacture Hydraulic Cylinder With The Following Constructions

• Tie rod
• Welded
• Threaded
• Bolted
• Block

Salient Features Of Hydraulic Cylinders

• Honed Tube : All the tubes are micro honed for superior surface finish with Ra value less than 0.3 microns.
• Piston rod : En 8 to En 353 are ground and hard chrome plated with 25 microns minimum plating thickness.
• Piston : Single piece design to accommodate low friction seals.
• End covers : Accurately machined cast iron / mild steel plates.
• Sealing systems : Low friction seals with operating Pressures upto 80 mpa from BUSAK and SHAMBAN.
• Guidance systems : Turcite / Phosphor bronze bushings to ensure positive guidance.

Minimum Order Quantity : 5

We are a well-known Hydraulic Flow Meter Manufacturer, Exporter and Supplier. Hydraulic Flow Meter, available with us, is precision engineered using top grade raw materials. The offered Hydraulic Flow Meter is in compliance with the highest quality standards. Clients can avail Hydraulic Flow Meter from us at the leading market prices. Minimum Order Quantity : 5

We offer Electro Hydraulic Training Kit.For the diverse requirements of our clients, we are engaged in offering a wide range of Electro Hydraulic Training Kit. These products are strong and sturdy in nature and ensure long lasting service life. Our products are technically sound and offer hurdle-free performance. Optimum strength, reliable performance and smooth functioning are some of the salient features of these products. Features: Silent in operationEasy to operateLight and manoeuvrable

The hydraulic systems division designs and manufactures Hydraulic Pump for industrial and derivative markets. The Hydraulic Pump product line provides unmatched efficiency and reliability in a compact, lightweight package with an exceptionally high hydraulic horsepower-to-weight ratio. Standard and custom Hydraulic Pumps are available for a variety of applications. Hydraulic Pumps include engine-driven, ram air turbine-driven, AC and DC electric motor-driven pumps, hydraulic power supplies, power transfer units, and electro-hydrostatic actuation systems. Applications

• Most commercial, military, and general aviation aircraft
• Unmanned, space, and military ground vehicles

Technical Highlights

• Variable displacement axial piston pump designs with pressure compensation
• Phosphate-ester-based fluids and hydrocarbon-based (MIL-PERF-87257, 83282, 5606) operating fluids
• Conventional bearing or advanced lightweight bearing designs available.
• Operating pressures from 1, 000 to 8, 000
• Flows rated up to 100 gpm (378 l/min)
• Speeds up to 20, 000 rpm
• Solenoids, depressurization valves, and/or blocking pistons available to reduce operating torque
• Case drain gerotor pump and low-inlet impeller functions available for improved system operational efficiency

Minimum Order Quantity : 5

We are offering Portable Filter Carts & Mobile Filtration Systems under our Hydraulic Filtration Units. We provide a full range of mobile Hydraulic Filtration Unit to meet every critical industrial filtration need, available for purchase and available to rent. The Hydraulic Filtration Units are ideal for use in industrial plants and with many other applications because they are versatile, reliable, and portable. A portable Hydraulic Filtration Unit can be used to filter nearly any type of hydraulic fluid, including insulating oils, lubricating oils, and coolants. Our Hydraulic Filtration Units are perfect for removing particulate and water contamination from hydraulic fluids, such as high-viscosity lubricating oil. A filter cart can also help transfer and replenish new fluids, as well as flush fluids that are already in service with high-efficiency elements. Our mobile Hydraulic Filtration Unit can handle flow rates as low as 0.5 GPM all the way to higher flow rates (such as 5 GPM, 10 GPM, and 22 GPM) that are required in most industrial applications. We offer a large variety of materials and types of construction, including stainless steel and explosion-proof options! Hydraulic Filtration Unit Is Ideal For The Following Applications

• Particulate and Water Removal
• Turbine Oil Conditioning
• Liquid Coalescing and Separating
• Hydraulic Reservoir Maintenance
• Refinery Upset Conditions
• High-Viscosity Lubrication and Hydraulic Oils
• Gearbox Flushing & Oil Change
• Complete System Flushing
• Transfer and Replenishment of New Fluids
• Filtration System Upgrades
• Varnishing
• Going Green - Reusing Oil and Extending Machinery Life

Minimum Order Quantity : 5

We are engaged in offering light weight, double acting, oil return and high pressure Hydraulic Jacks. Hydraulic Jacks are designed to provide oil force in both the advance and retraction of ram, in vertical & horizontal position, where cycle time is crucial. Hydraulic Jacks are mainly used for hydraulic testing machine and for lifting, lowering, spreading of structures, bridges, heavy machinery, etc. The offered Hydraulic Jacks are ideal for heavy duty applications. Features / Benefits

• High strength, alloy steel body for better life. Double acting.
• Hard chrome plated ram to resist scoring and corrosion.
• For high tonnage jacks, QCC is fitted on a safety manifold block to prevent protudence and possible damage while handling.
• High pressure long life seals. QCC with dust cap.
• Wiper to arrest ingress of foreign particles.
• Relief valve in return position prevents accident against over pressure intensification.
• Adequate gripping by grooved saddle. High tonnage & custom strokes available on request.
• Bottom mounting holes, collar threading, tilting saddle and hose burst features available on request.
• Port size 3/8th inch NPT. L working pressure 650 bar.

Minimum Order Quantity : 5

Pilot-to-close Hydraulic Logic Valves are primarily used for bi-directional flow switching applications. The poppet in the pilot-to-close Hydraulic Logic Valve is spring biased to the closed condition. With no pilot signal at port 3, the Hydraulic Logic Valve will open allowing flow in either direction between work ports 1 and 2 once pressure at one of the work ports reaches the biased spring setting. Applying a sufficient externally generated pilot force to port 3 of the Hydraulic Logic Valve closes the poppet creating a low leak seal between port 1 and port 2. Poppet Hydraulic Logic Valves are typically used to perform high flow directional switching operations using small low power pilot valves to control the sequence of the directional operation.

• A single logic valve can be used to control 2-way, on/off switching.
• Multiple elements in a bridge arrangement can control 3-way or 4-way directional switching.
• Since each logic valve is individually controlled, the timing, sequence, and overlap of directional functions can be controlled very precisely.
• Uni-directional or bi-directional flow can be achieved, depending on the valve selected.
• Flows in excess of 80 gpm can be controlled through a single logic element, and more than one logic valve can be used in parallel to control flow in excess of the rated flow of a single element.
• Poppet construction provides a low leak directional control.

Spool TypeSpool type Hydraulic Logic Valves can also be used for directional switching, however, they are typically used in modulating applications to control flow or regulate pressure. Virtually any pressure or flow control function can be achieved with a spool type Hydraulic Logic Valve including; restrictive or priority flow control, pressure relief, pressure reducing, sequencing, and unloading. The spools in this category of Hydraulic Logic Valves are balanced designs; the spool area at the work port (port 1) and the pilot port (port 3) are equal (1:1). The spool is held in a biased condition by a spring. Venting the pilot at port 3 creates an unbalanced condition causing the valve spool to modulate open or close, depending on the valve chosen. This spool design makes the valve very stable because the forces acting to open and close the valve are in balance. Normally closed spool Flow Control / Compensators Parker offers two types of logic valves for flow control functions.

• Normally open spools function as a restrictive type compensator.
• Normally closed spools function as a priority or by

Minimum Order Quantity : 5