Our Products
- Capacity: 1.5 tons, 2 tons, 3.5 tons
- Electronic control for smooth transmission and acceleration
- Twin jack hydraulic system with guided lift
- Pulling type tie bar to prevent buckling of tie bar
- Belly button for operator safety
- Battery status indicator
CHASSIS :
Fabricated from rolled channels and plates.
DRIVE UNIT AND TRANSMISSION :
Traction motor is mounted above the drive wheel, drive to the wheel is transmitted through two stages chain reduction & final reduction by gear & pinion. The entire unit swivels on heavy duty self aligning bearings.
ELECTRICAL SYSTEM :
Control panel located below steering handle, consists of four heavy duty solenoid operated contractors with arc shields & magnetic blow outs for forward/reverse motion & cutting out two stage resistance bank. The complete electric circuit is protected by adequate rated fuses
CONTROLS :
Controls for forward reverse motion, horn, light, emergency cut-off & key switch are mounted on dash board. Accelerator & mechanical brake is foot operated.
BRAKE :
The brake comprises of two internal expanding shoe mounted on rear axle, with parking brake facility.
OPTIONAL EXTRAS :
Chequered platform, manual or motorised elevation, low voltage battery discharge alarm, front suspension, 1800mm long platform and scissor type platform for all models. Hydraulic brakes and rear suspension for high platform models only. Electronic controls for soft and jerk free transmission provides the following advantages :
1. No wastage of battery power resulting in more work out put.
2. Lower maintenance cost and downtime of equipment.
Hand Pallet Truck - SJ series
- Capacity: 1500-2500 kgs
- Standard version -5 mm MS fabricated chassis.
- Full Stainless Steel version available
- Excellent maneuverability
- Hard chrome plated shaft and plunger- Pallet entry rollers
- Articulation of steering wheels allows smooth running on
uneven floor- Sealed hydraulic unit
- Strong light weight pressed steel chassis
- Maintenance free sealed bearing
- Protection of operator's hand by convenient shape of tiller
Durability/Reliability
- Single Piece, C-Channel Design Pressed Steel Forks for
Maximum Strength
- Solid Steel, Fixed Pushrods
- Epoxy Base, Oven Baked Paint Finish
- High Tensile Strength Steel Frame
- 10 Grease Points for Improved Lubrication
- Polyurethane Load and Steer Wheels (optional)
Operability/Performance
- Variable Speed Lowering for Fragile Loads
- Precise, Lightweight Steering Control
- Low Noise Levels and Low Rolling Resistance
- Low profile Trucks available
- Precise Lifting/Lowering Control
- 180-degree Steering Arc for Excellent Maneuverability
- Single Load Wheels with Entry/Exit Rollers, also Tandem Load Wheels version.
Ergonomics
- Large Diameter Hand Grip with Curvilinear Handle Design
- Three Position Handle with Neutral Position
- Strong Handle Return Spring Design
Options
- Various Fork Widths (20.5", 22" & 27")
- Various Fork Lengths (36", 42" & 48")
- Nylon Load and Steer Wheels
- Tandem Load Wheels (Nylon Only)
- 48" Load Backrest
- Overload Protection Valve
- Quick-Lift Pump Unit
- Parking Brake
- Stainless Steel Mode (4, 500 lb Capacity)
STAR FEATURES:
- High Performance Electronic Control.
- Gradient Start.
- Smooth Acceleration.
- Safe Operation with Integrated Handle.
- Wrap Around Hand Guards.
- Belly Button Safety Reversing Switch.
- Electric Horn.
- Excellent Stability & Manoeverability.
- Compact Dimensions.
- Fast Battery Change.
- Exceptional Easy Access to All Components.
- Power Unit & Leg Assembly Independently Mounted.
- Twin Heavy Duty Hydraulic Jack System.
- Pull Type Tie Bar in place of Conventional Pushing Type to Prevent
Common Problem of Bending of the Bars.
- Hydraulic Jacks are Subjected to only Axial Vertical Load and no pull as
in conventional trucks resulting in reduced wear and prevention of Oil
Leakage.
- Lifting and lowering of the leg assembly is fully guided by channel and
wide contract low friction polymer pads.
- Heavy duty Spring Loaded castor wheel as standard to prevent side
ways tilting during sharp turns.
- The fork carriage is an integrally welded unit channel forks, chain and
pulley mechanism with pull bars.
- The integrally welded power unit frame in addition providing rugged
structural base for max, durability also protects the truck components.
- Battery State of Charge Indicator