Ceramic Ferrules are used at the inlet of the Shell & Tube type heat exchanger to protect the tube inlets from hot gas corrosion and abrasive particle erosion.

Techno Cera Ferrules are manufactured using 98% High Alumina. These ferrules exhibit excellent mechanical wear resistance, corrosion resistance and thermal resistance properties.

They are manufactured in various sizes & shapes as per customer requirements.

Igniters are commonly used for lighting the burners of industrial and domestic boilers, hot air generators, etc.

Alumina is used as insulating material to withstand high voltage required to generate spark and high operating temperature up to 1400^oC near the burners. Techno Cera Igniters are manufactured in various sizes and standard designs like clamped, threaded, etc. The electrodes are made from special Nickel / Magnesium alloy to withstand temperature up to 1400^oC

Lead Zirconate Titanate

Lead Zirconate Titanate ceramics are used in Low Power applications such as low power transducers, acoustic sensing elements, flaw detection probes.

Due to there high di-electric constant, high voltage sensitivity, volume resistivity and stability over a wide temperature range, they are ideal choice for these applications.

Lead Zirconate Titanate also used in High Power applications such as ultrasonic welding, ultrasonic mixing/dispersion, ultrasonic surgery.

Due to there excellent dielectric stability and low mechanical loss at high drive conditions, they are ideal choice for these applications.

These are are made in various shapes and sizes as per customer requirements

Ceramic wire drawing cones, rings & guides are commonly used for drawing and production of
non-ferrous wires in the wire and cable industries.

As Zirconia/Alumina exhibit high toughness, high hardness, good abrasion and corrosion resistance, this makes them ideal choice material for wire drawing applications.

Techno Cera wire drawing cones, rings & guides are manufactured in various shapes and sizes & ground to precise dimensions as per customer requirements

Ceramic is commonly used as a mating ring together with carbon-graphite opposite seal face in mechanical seal kits which in turn used in chemical pump applications.

Since Alumina exhibit high hardness, good abrasion resistance & good resistance to acid and mild alkaline solutions. This makes them suitable choice for chemical seal faces. They are used in corrosive environments like acids including Hydro fluoric acids, molten salt solutions, and mild to medium alkaline solutions.

Techno Cera Chemical seal faces are manufactured in AL99.5, in various sizes and shapes like DA type, L type, T type etc. Ceramic Sleeves are manufactured in sizes Dia 28.6 X 140 mm, 35 X140 mm, etc. And Water Pump Seal Faces are manufactured in AL96 Pink and White in various sizes like Dia 21X13X5.5mm, 27X17X5.5mm, 28X17X5.5mmX31X20X8mm, 36X27X6.5mm, 43X33X8mm 66.6X52X8mm They are lapped within 20 micron Parallelism, and polished to surface finish Less than 0.3 microns and flatness within 2 light bands and ground to finish sizes as per customer requirements.

Ceramic thread grades are used in textile machineries to guide, to change direction, to twist, to control tension of textile yarns.

Since Titania and Alumina exhibit high hardness, good abrasion and corrosion resistance, fine grain structure, yarn friendly surface finish, this makes them ideal choice material for textile thread guides.

Techno Cera thread guides are manufactured in various shapes and sizes & various surface finish like tumbled finish, matt finish and high polished finish.

Ceramic Welding Nozzles are best material for WIG/TIG welding, plasma welding and cutting.

Techno Cera Welding Nozzles are manufactured using 98% High Alumina. These welding nozzles exhibit high-temperature, high insulation and chemical resistance.

Welding Nozzles are manufactured in various thread sizes like 3/8" BSP, 1/2" BSP, 5/8" BSP, 3/4" UNF and 7/16" BSF and in several nozzle lengths and diameters.

A choke is used to control the flow of fluids and is usually mounted on or close to the Christmas tree. High pressure gas/oil, with abrasive sand minerals passes through these chokes at high speed causing rapid wear. Bean chokes contain a replaceable insert, or bean, made from hardened steel/ceramic or stainless steel/tungsten carbide or similar durable material.

Techno Cera Bean Chokes are lined with a high hardness, abrasion and corrosion resistant 98.5% Alumina or Tungsten Carbide liners, to protect them from corrosive and abrasive wear.

WE manufactures a big range of bean chokes to match 'OCT'Type FC140, 'ThronillCraver', Gray Tool', Cameron' & types. These are manufactured with a precise diameter hole that forms the choke, through which all the abrasive/corrosive fluids must pass. Beans are available in a complete range of sizes, generally identified by the choke diameter stated in 64ths of an inch