Pit Type Furnace  

Pit Furnaces are used for variety of Heat Treatment Processes

Commonly used for tempering of Automobile parts and Annealing of M.S. wire.

Mode of Heating - Electrical / L.D.O. Fired/ Gas Fired

Forging Furnace - Chamber Furnace

• For pre heating of billets and ingots forging furnaces are used
• The temperature maintained inside these furnaces is around 1200 to 1250 °c
• An open fireplace system is used through which most of the heat is transmitted via radiation.
• The Furnace operate around 16 to 18 hours a day, capacity can be vary from 250 Kg to 30 Ton per batch.
• The Operational time cycle in forging furnace is divided into Heat up Time, Soaking Time and Forging Time.
• The Consumption of fuel depends upon type of feed and number of reheat required.
• With Newly VENEERING INSULATION TECHNOLOGY it possible to reduce fuel consumption up to 50 % and increases the refractory life and production rate with faster start up heating time with low capital investment.
• Depend on the charge specification we can also suggest the Pusher Furnace for forging

We are one of the prominent project engineering companies engaged in designing, manufacturing and supplying high performance Bogie Hearth Furnace for various heat treatment processes.

We have successfully commissioned bogie furnaces from 1 ton/batch upto 60 Ton / Batch.

ery popular in steel industries for Rolling Mill & Re- Rolling Mill.

Relatively low installation and maintenance cost compared to moving hearth furnace

Possible to push the charge (Billets / Ingots) along skids with water cooled supports that allow both the top and bottom faces of the charge (Billets / ingots) to be heated.

The walking beam furnace allows the product to be heated from all sides, where a walking hearth furnace only allows product to be heated from top

The walking hearth furnace allows the charge to be transported through the furnace by lift and shift mechanism.

There is no major mechanism difference between walking hearth and walking beam furnace.

Attractive Features

1. Simplicity of Design and Ease of Construction


2. Very effective heating and soaking of billets.


3. Ability to cater for different billet sizes (within limits), negligible water cooling energy losses and no physical markings on charge.

We have successfully designed, installed & commissioned roller hearth furnaces. Basic specifications include -

Re - Heating Furnace are used for reheating of billets. Charging may be done as cold charging or hot charging. We have supplied , erected & commissioned these furnaces all around the world in the capacity range of 10 TPH to 65 TPH. These are suited for MS, CS, SS & Special alloy steels.

• 
  

  We design & supply Crucible Furnaces for Aluminium melting application.

  
  

Our furnace is supplied with in house built Therm Process Burners.

• Continuous annealing furnaces are designed for the processing of SS or Copper wire, rod, strand, strip and tube products.


• These furnaces are ideally suited for copper, copper alloy, nickel, nickel chrome, titanium, stainless steel and refractory metals.


• Therm Process's Annealing Furnace features heavy-duty construction, an energy saving combination of fiber and brick insulation, precise temperature control and requires minimal maintenance.


• The Furnaces are Gas Fired or Electrically Heated In case of gas fired furnace no of smallTherm ProcessMake gas burners are provided to achieve excellent temperature uniformity.


• In case of electrical heating type the heating elements are provided with either circular type or in grooved refractory. The design of heating element is very vital for long and trouble free life.


• Therm Process provides low watt density elements in the electric furnace.

Pit Type Furnace  

Pit Furnaces are used for variety of Heat Treatment Processes

Commonly used for tempering of Automobile parts and Annealing of M.S. wire.

Mode of Heating - Electrical / L.D.O. Fired/ Gas Fired

Forging Furnace - Chamber Furnace

• For pre heating of billets and ingots forging furnaces are used
• The temperature maintained inside these furnaces is around 1200 to 1250 °c
• An open fireplace system is used through which most of the heat is transmitted via radiation.
• The Furnace operate around 16 to 18 hours a day, capacity can be vary from 250 Kg to 30 Ton per batch.
• The Operational time cycle in forging furnace is divided into Heat up Time, Soaking Time and Forging Time.
• The Consumption of fuel depends upon type of feed and number of reheat required.
• With Newly VENEERING INSULATION TECHNOLOGY it possible to reduce fuel consumption up to 50 % and increases the refractory life and production rate with faster start up heating time with low capital investment.
• Depend on the charge specification we can also suggest the Pusher Furnace for forging

We are one of the prominent project engineering companies engaged in designing, manufacturing and supplying high performance Bogie Hearth Furnace for various heat treatment processes.

We have successfully commissioned bogie furnaces from 1 ton/batch upto 60 Ton / Batch.

ery popular in steel industries for Rolling Mill & Re- Rolling Mill.

Relatively low installation and maintenance cost compared to moving hearth furnace

Possible to push the charge (Billets / Ingots) along skids with water cooled supports that allow both the top and bottom faces of the charge (Billets / ingots) to be heated.

The walking beam furnace allows the product to be heated from all sides, where a walking hearth furnace only allows product to be heated from top

The walking hearth furnace allows the charge to be transported through the furnace by lift and shift mechanism.

There is no major mechanism difference between walking hearth and walking beam furnace.

Attractive Features

1. Simplicity of Design and Ease of Construction
2. Very effective heating and soaking of billets.
3. Ability to cater for different billet sizes (within limits), negligible water cooling energy losses and no physical markings on charge.

We have successfully designed, installed & commissioned roller hearth furnaces. Basic specifications include -

Re - Heating Furnace are used for reheating of billets. Charging may be done as cold charging or hot charging. We have supplied , erected & commissioned these furnaces all around the world in the capacity range of 10 TPH to 65 TPH. These are suited for MS, CS, SS & Special alloy steels.

• We design & supply Crucible Furnaces for Aluminium melting application.

Our furnace is supplied with in house built Therm Process Burners.

• Continuous annealing furnaces are designed for the processing of SS or Copper wire, rod, strand, strip and tube products.
• These furnaces are ideally suited for copper, copper alloy, nickel, nickel chrome, titanium, stainless steel and refractory metals.
• Therm Process's Annealing Furnace features heavy-duty construction, an energy saving combination of fiber and brick insulation, precise temperature control and requires minimal maintenance.
• The Furnaces are Gas Fired or Electrically Heated In case of gas fired furnace no of smallTherm ProcessMake gas burners are provided to achieve excellent temperature uniformity.
• In case of electrical heating type the heating elements are provided with either circular type or in grooved refractory. The design of heating element is very vital for long and trouble free life.
• Therm Process provides low watt density elements in the electric furnace.