Write a Review
Our Products
We offer a complete product range of GfG Micro IV Single Gas Detector, GfG G450 Multi Gas Detector, IR Sensors GfG G450 Multi Gas Detector, ION Science Gas Check Leak Rate Detector and Carbon Dioxide (CO2) Monitoring Detector
Single gas detector for toxic gases, hydrogen and oxygen
Housed in a titanium coated ABS case the MICRO IV provides maximum amount of safety in th smallest size. The non-disposable MICRO IV is available in a variety of gases with features you would expect in multi-gas units.
The World's Most Advanced Confined Space Gas Detector
The G450 Confined Space Gas Detector continuously measures up to four hazards (CO, H2S, O2 and percent LEL combustible gas) in air.
The G450 is compact, robust and very easy-to-use. The dust proof and highly water resistant (IP-67) housing is designed to survive the toughest environmental conditions. The housing even includes a built-in rubberized boot to withstand the hard knocks of confined space entry.
The World's Most Advanced Multi-sensor Atmospheric Detector
The durable G460 continuously measures and displays readings for up to six gases at the same time.
The G460 is compact, robust and very easyto- use. The dust proof and highly water resistant (IP-67) housing is designed to survive the toughest environmental conditions. The housing even includes a built-in rubberized boot to withstand the hard knocks of confined space entry.
Designed specifically for the detection and measurement of CFC's, HFC's and HCFC's.
GasCheck R2pc is a light weight, handheld leak detector specifically designed for the detection and measurement of refrigerant and air-conditioning gases. At the heart of the instrument is a unique sensing system optimised for refrigerant gas leak detection. The inboard pump and flow management system enables the instrument's high sensitivity and rapid response to detect the smallest of CFC's and HCFC's leaks - 0.2 gm/yr.
Robust and reliable, the instrument can be switched to display leak rates in gm/yr or ppm. Leak rate measurements are continuously updated allowing the leak to be accurately located and the leak rate exponential measured.
Stationary monitoring of carbon dioxide (CO2)
The IR 24 does not contain any moving parts, which may be subject to wear and tear. This ensures a long lifetime and low maintenance cost. Additional safety is provided by the permanent self-check and function test of the GMA controller. Sensor and electronics are protected in a solid enclosure from dust and water according to IP 54. This ensures that water cannot enter the detector, even in wet environments.
Behind a service lid on the front of the IR 24 you find potentiometers and test connectors for easy adjustment of zero point and span. This allows one-man calibration on-site and reduces service down-time.
SAM Smart Area Monitor EC 36 - Stand alone
The EC 36 is a stand-alone transmitter. In every EC 36 there is a sensor, control electronic and relays for triggering of alarms. LEDs in the front panel immediately indicate the alarm. The signal output is provided as a 4.20 mA signal.
The EC 36 is the most enhanced single point gas detector available offering features never known to the industry. Equipped with AutoCal, the EC 36 can be comfortably calibrated in a matter of seconds. A 17 mm high backlight LCD-display indicates the gas concentration, status report and, if operated in service mode, all settings. In applications where the display of the EC 36 cannot be read because of its mounting position, a remote display is easily connected to an interface. Using the remote control, nonintrusive remote calibration can be performed, making forklifts or ladders a thing of the past.
Low cost long-term solution
Particular long sensor life makes the ZD21 a low cost transmitter for oxygen monitoring. The expected lifetime for the sensor is 5 years in continuous operation. A robust aluminium casing protects the sensor and the circuitry from impacts, splash water and dirt.
The ZD21 is an "intelligent" transmitter. The comprehensive electronic allows for easy operation and maintenance and also increases the operational safety and accuracy. In less than 2 seconds the ZD21 responds to changing oxygen levels. This extremely short response time allows to take measures in time to prevent considerable damage.
Fixed PID Detector for Continuous VOC Detection
TVOC is a fixed photoionisation detector (PID) designed for continuous measurement of total volatile organic compounds (VOCs). New ATEX approvals enable a 3 wire TVOC system to be used in Zone 2 hazardous areas, without safety barriers. ATEX and IECEx approvals allow TVOC to be used in Zone 1 hazardous areas, with safety barriers.
The World's Most Advanced Multi-sensor Atmospheric Detector
The durable G460 continuously measures and displays readings for up to six gases at the same time.
The G460 is compact, robust and very easyto- use. The dust proof and highly water resistant (IP-67) housing is designed to survive the toughest environmental conditions. The housing even includes a built-in rubberized boot to withstand the hard knocks of confined space entry.
Indoor Air Quality AQ Expert
Providing the latest in Detection & Data Logging for IAQ testing in Buildings, Hospitals, Schools, Labs, Clean Rooms, Airports, & more
Custom to Your Application: Up to 11 different parameters and gases to meet the needs of most air quality analysis
REAL-TIME Data Logging: Save and graph using USB or wireless Bluetooth to a PC
Easy Calibration: Built-in menu driven calibration procedure
Made in USA: Designed and manufactured in the USA
Desktop Models: Ideal for Long-Term Surveys and Remote Detecting Applications
The DustTrak DRX is also offered as a standard desktop (Model 8533), as well as a desktop with external pump (Model 8533EP.) Both models have manual and programmable data logging functions, making them ideal for unattended applications. The standard desktop model is most suitable for indoor, continuous monitoring, while the desktop with external pump is designed for 24/7 unattended, remote monitoring outdoors.
The DustTrak DRX desktop models come with USB (device and host), Ethernet, and analog and alarm outputs allowing remote access to data. User adjustable alarm setpoints for instantaneous or 15-minute short-term excursion limit (STEL) are also available on desktop models. The alarm output with user-defined setpoint alerts you when upset or changing conditions occur.
For reliable leakage detection in cooling circuits
The MiniCal III system was designed especially for detection of ammonia leakages in cooling circuits. Many years of experience lead to the development of this robust and practical system which can be used in water as well as in brine circuits.
By using ion selective resp. gas sensitive electrodes a reliable and early detection of leakages in cooling circuits is provided. Even at lowest Ammonium, resp. Ammonia concentrations safety precautions can be taken in time. The integrated controller provides a linear 4-20 mA output signal which can be connected to an evaluation unit or directly to a PLC.
The universal measuring amplifier/controller for pH, redox and chlorine measuring applications
pH, redox and chlorine/ozone measurements are required daily in many industrial water applications. It is therefore especially important that the measuring instruments used are reliable, simple and uncomplicated to use. The clear layout of the front panel and the simply labelled operating buttons of the VARIOCON 2010 help the user to find his way around the operator control levels without any difficulty.
The modern configuration of the instrument enables individual settings to be made for many measuring and control tasks in industrial and municipal applications such as swimming pools, neutralizing plants, refrigeration plants, sewage plants, water treatment, chemical plants, . - wherever the pH value or redox reading gives an indication of contamination or neutralization. The same applies to chlorine and ozone measurements (especially in swimming pools).
The Photoacoustic Field Gas-Monitor - INNOVA 1412 is a highly accurate, reliable and stable quantitative gas monitoring system. It uses a measurement system based on the photoacoustic infrared detection method, and is capable of measuring almost any gas that absorbs infrared light.
Gas selectivity is achieved through the use of optical filters. By installing up to five of these filters in the 1412, it can measure the concentration of up to five component gases and water vapor in any air sample. Although the detection limit is gas-dependent, it is typically in the ppb region. The accuracy of these measurements is ensured by the 1412's ability to compensate for temperature and pressure fluctuations, water vapor interference and interference from other gases known to be present. Reliability of measurement results is ensured by regular self tests, which the 1412 performs. By the nature of this measurement system, it requires no consumables and very little regular maintenance, for example, for most applications recalibration is only necessary one - two times a year.
The Photoacoustic Multi-gas Detector - INNOVA 1314 is a highly accurate, reliable and stable quantitative gas monitoring system. It uses a measurement system based on the photoacoustic infra-red detection method, and is capable of measuring almost any gas that absorbs infrared light.
Gas selectivity is achieved through the use of optical filters. By installing up to five of these filters in the 1314, it can measure the concentration of up to five component gases and water vapor in any air sample. Although the detection limit is gasdependent, it is typically in the ppb region. The accuracy of these measurements is ensured by the 1314's ability to compensate for temperature and pressure fluctuations, water vapor interference and interference from other gases known to be present. Reliability of measurement results can be ensured by regular self tests, which the 1314 performs. By the nature of this measurement system, it requires no consumables and very little regular maintenance, for example
Low cost long-term solution
Particular long sensor life makes the ZD21 a low cost transmitter for oxygen monitoring. The expected lifetime for the sensor is 5 years in continuous operation. A robust aluminium casing protects the sensor and the circuitry from impacts, splash water and dirt.
The ZD21 is an "intelligent" transmitter. The comprehensive electronic allows for easy operation and maintenance and also increases the operational safety and accuracy. In less than 2 seconds the ZD21 responds to changing oxygen levels. This extremely short response time allows to take measures in time to prevent considerable damage.
Continuously Detection Your Breathing Air.
Designed to meet OSHA requirements for the monitoring of Grade D respirable air from oil lubricated compressors this versatile instrument, with years of proven performance, can be used for a wide range of applications.
Equipped with a MOS Broad Range sensor, the monitor not only responds and alarms to excessive carbon monoxide which enters the airline system, but also to hydrocarbon contamination and other oxidizable toxic gases. A durable corrosion resistant and tamper proof case, rugged electronics, automatic purge, stable calibration and continuous sample flow indication, are all combined to insure trouble free operation. The RAM 50 is available in two models, the 1540 or 1541(with built in horn). Both may be purchased with or with out an airline filter system.
Portable Remote Compressed Air Detector
The GfG RAM 744-X remote monitor is a rugged and compact monitor for the detection of CO in compressed breathing air. It is the ideal monitor for portable applications where space is limited or where the environment is harsh. With a standard high pressure (120 psi) fitting on the inlet, it is easy to connect to virtually any air filtration system.
The RAM 744-X automatically adjusts the flow rate so there are no touchy flow meters to adjust.Calibration and maintenance are made simple with our innovative AutoCal system which allows automatic calibration with the turn of a dial. The alarm level is set at 10 ppm by default; however, it may be specified at 5 ppm. Any GfG Instrumentation RAM instrument can be custom-configured to meet the needs of the end users exact specifications.
The Best Safeguard for Quality Breathing Air
Designed to meet OSHA requirements for monitoring Grade D respirable air, this unit is equipped with a reliable electrochemical sensor that accurately indicates the level of carbon monoxide on an illuminated liquid crystal display. Adding versatility, this unit offers optional oxygen or dew point sensors for applications where detection or measurement is needed.
Calibration and maintenance are simple with our innovative AutoCalRsystem. Additional features including alarm relay contacts, user adjustable alarm point, low flow alarm indicator, and many more make this unit an intelligent choice. The RAM 4021 is available in four models, the 4021 (CO), 4021-1 (CO and O2), 4021-DPX (CO and dew point levels), and 4021-PR (CO and additional relay to signal power loss to monitor, complies with newest NFPA regulation). All models may be purchased with or without air line filter systems.
High Accuracy Infrared Thermometers
The NEW! Wahl DHS1900 High Temperature hand held infrared thermometer used for the Aluminum Industry. This models has an RS485 interface and 4-20mA analog signal output through two mini-USB ports below the LCD.
Long Distance Portable Infrared Thermometer
Wahl is pleased to introduce our NEW! Long Distance models to our line of Heat SpyRInfrared Thermometers. Widely used for non-contact temperature measurement and preventive maintenance in the Electrical Power Generation and Power Transmission industries, these new Heat SpyRInfrareds are preferred by maintenance engineers to easily search out hot spots at a safe and convenient distance.
WahlRHeat SpyRHybrid Infrared Thermometer
Wahl's Brand New Hand-Held Infrared Thermometers!
America's most innovative thermometer company. Palmer Wahl, manufactures precision temperature instruments. Wahl was the first to bring the industry a portable, non-contact, handheld infrared thermometer at an affordable price point. Today, Wahl is pleased to introduce this new model to our famous line of Heat SpyRInfrared Thermometers. These incredibly accurate and robust Heat Spy's will help you diagnose any problem, and prevent costly equipment downtime. The variety of features enable you to select the most appropriate Heat SpyRfor your application.
Model Number 2500MVX
The pocket-sized microprocessor-based Heat-Prober Type K thermometer updates readings three times per second with an accuracy of +-0.2% of reading +-1 digit in 1oF oroC resolution. The precision cold junction is compensated with a unique, permanently calibrated circuit. Advanced electronics are housed in ABS plastic, thoroughly tested for environmental integrity and subjected to 4-foot drop tests, battery life and running life tests. All units are calibrated with simulated EMF inputs and powered during a high-temperature burn-in cycle. The result is a thermometer so durable and reliable that it comes with a 3-year warranty. Meter range is -100 to 2500oF. Features a bright .5" high red LCD display for normal to bright lighting conditions. The 2500MVX is powered by an easily replaceable single standard 9V battery.
Type K Thermocouple Meter 70 to 1370oC
Model Number 3200M
The pocket-sized microprocessor-based Heat-Prober Type K thermometer updates readings three times per second with an accuracy of +-0.2% of reading +-1 digit in 1oF oroC resolution. The precision cold junction is compensated with a unique, permanently calibrated circuit. Advanced electronics are housed in ABS plastic, thoroughly tested for environmental integrity and subjected to 4-foot drop tests, battery life and running life tests. All units are calibrated with simulated EMF inputs and powered during a high-temperature burn-in cycle. The result is a thermometer so durable and reliable that it comes with a 3-year warranty. Meter range is 70 to 1370oC. Features a bright .33" high red LED display for normal to low lighting conditions. The 3200M operates on a rechargeable 6.25V NiCad battery pack. Includes battery recharger/AC line adapter.
Type S Dipstick System for Ferrous Metal
Use in molten iron and steel alloys with or without slag for measuring melts in ladles and melt-pots. Stable readings are obtained in 6-8 seconds. Dipstick comes with one expendable tip. Spare tips are sold separately. 48" length dipstick with 45oangle bend (12" from tip), meter with RTC832 expendable tip, oF.
Models Available:-
High Accuracy Infrared Thermometers
Wahl's Temp-PlateRtemperature recording labels are NIST traceable, self-adhesive and can be read at a glace. Where exacting temperature is critical, their miniaturized size permits installation on parts and in areas where other recording instruments prove impractical.
Vikash Bajaj (Three S instruments Pvt. Ltd.)
J-110, West Patel Nagar
New Delhi-110 008 (INDIA) - 01233
Share us via
