TRANSHEAT TECHNOLOGIES PR...

Thermal design of Heat exchanger using HTRI software and Fired heater using Xfh. Service provider for new and existing both units. Critical fluid / services handled.

• 
  Thermal Design Of Heat Exchanger
• 
  Sizing Of Heat Exchanger
• 
  HTRI Design Of Heat Exchanger
• 
  Heat Exchanger Design Services
• 
  Furnace Design Services
• 
  Fired Heater Design Services
• 
  Fin Fan Cooler Thermal Design Services
• 
  Air Fin Cooler Design Services
• 
  Air Cooled Heat Exchangers

Forced draft, Induced draft, Natural draft, units with chimney. Plug header, Cover headers with tapped / flange bolting, Split headers. Units with louvers / Recirculation systems for winterization. Re-rating and performance validation of existing units. Review of vendor documents.

• 
  Tube Bundle Drawings
• 
  Thermal Design Of Air Cooled Heat Exchanger
• 
  Thermal Design Of Air Cooled Heat Exchanger Using HTRI Software
• 
  Structure Design Of Air Cooled Heat Exchanger
• 
  Steel Fabrication Drawings Of Air Cooled Heat Exchangers
• 
  Mechanical Design Of Fin Fan Cooler Using Compress Software
• 
  Mechanical Design Of Air Cooled Heat Exchanger
• 
  Mechanical Design Of Air Cooled Heat Exchanger Using PV Elite Software

Design of waste heat recovery unit to improve energy efficiency and thus reduce energy consumption as well as GHG emissions. Evaluate possibility of various design options - single or two pass on flue gas side, horizontal / vertical tube arrangement - based on thermal and hydraulic design. Evaluate need of expansion joints to take care of differential thermal expansion.

• 
  Waste Heat Recovery System
• 
  Waste Heat Recovery System Design
• 
  Heat Recovery System
• 
  Heat Recovery System Design
• 
  Heat Recovery From Hot Gases
• 
  Heat Recovery From Furnace Exhaust
• 
  Heat Recovery From Exhaust Gases

Fixed tube sheet, floating head and u-tube units. All TEMA type units. Re-rating and performance validation of existing units. Complete detail engineering and fabrication drawings. Design of stub-in bundles, steam coils in tanks, heating coils in sulfur pits.

• 
  Thermal Design Using HTRI Software
• 
  Thermal Design Of Shell And Tube Heat Exchanger
• 
  Mechanical Design Using PV Elite Software
• 
  Mechanical Design Using Compress Software
• 
  Mechanical Design Of Shell And Tube Heat Exchanger
• 
  General Arrangement And Fabrication Drawing Services

Mechanical design as per ASME section VIII division 1 and 2. Mechanical design by using PV elite and compress software.

• 
  Mechanical Design - Shell And Tube Heat Exchanger
• 
  Mechanical Design - Process Columns
• 
  Mechanical Design Of Reactor
• 
  Mechanical Design Of Heat Exchanger
• 
  Mechanical Design As Per ASME Section VIII Division 2
• 
  Mechanical Design As Per ASME Section VIII Division 1

Natural draft, Forced draft, Induced draft and balance draft heaters. Heaters with on-board or external APH systems. Re-rating . revamping studies to improve heater thermal efficiencies and performance.

• 
  Furnace Revamping Services
• 
  Fired Heater Detail Engineering Services
• 
  Design Of Furnace
• 
  Design Of Fired Process Heater
• 
  Design Of Fired Heater

Rating of existing units for new service conditions. Complete detail engineering and fabrication drawing. Evaluation of fitness for service / remaining life based on existing condition.

• 
  Mechanical Design Of Pressure Vessels Using PV Elite Software
• 
  Mechanical Design Of Pressure Vessels
• 
  Mechanical Design Of Pressure Vessel Using Compress Software
• 
  General Arrangement And Detail Fabrication Drawing Services

Columns with internals (risers, downcomers, vortex breaker, supporting rings, etc.) and other external appurtenances like ladders, platforms, handrails, pipe support cleates, etc.

• 
  Mechanical Design Of Process Columns Using PV Elite Software
• 
  Mechanical Design Of Process Columns Using Compress Software
• 
  Mechanical Design Of Process Columns
• 
  General Arrangement And Detail Fabrication Drawing Services For Process Column