VISHWA Systems Pvt. Ltd.

Ambad, Nashik, Maharashtra

In Sugar factory the massecuit going to the centrifugal machine (‘C’ massecuit in particular) should be at a specific temperature so as to minimize its viscosity and to avoid overloading of centrifugal motor. Massecuit is cooled in crystallizer to extract maximum sugar from molasses but the disadvantage of cooling is, massecuit while cooling gets more viscous, sticky & does not flow freely up to the centrifugal machine. The machine also gets ununiformly overloaded, thus it’s purging capacity reduces.  To overcome all these problems there arises the need of a heater that raises the temperature of massecuit. The heater should fulfill following things. The heater design should be such that the massecuit gets heated quickly during its transit time from pug mill to centrifugal machine. If not then the problem of raise in molasses purity arises.  The heater must have minimum retention time.  The heater should be dimensionally small and compact so that it can be fitted above the centrifugal machine, below pug-mill.  The most important is that the heater should have minimum maintenance. Heating media for the heater should be such that the co-efficient of heat transfer should be high so that the massecuit gets heated quickly during transit time through the heater.  ‘ VISHWA’  Transient Heater fulfills all the above points so it can be really called as  ‘TRANSIENT HEATER ’. Heating media in all conventional Transient Heaters is hot water. The co-efficient of heat transfer from liquid (hot water) to semi solid i.e. massecuit is very less, but that of vapour to liquid is very high. Vapours when get condensed a large amount of ‘Latent Heat’ is released.  ‘VISHWA’ Transient Heater is designed, based on this phenomenon. Working Principle   Self-generated low temperature vapours are used as heating media in ‘VISHWA’ Transient Heater. Input energy required to run the Heater is only about 20 Kgs. of 100 PSIG. steam per hour. Heat energy of steam is transferred to the distilled water (Condensate) filled in the part of heater called ‘Vaporizer’. Condensate in the vaporizer gets evaporated and vapours are produced. These vapours are used as heating media in the Transient Heater which circulate through S.S. tubes and get condensed again after letting out the latent heat to the massecuit. Condensate flows back in to the vaporizer and again vapours are produced. This is how massecuit heating continues in Transient Heater. The heating media loop is completely sealed and kept under vacuum to generate vapors at low temperature and heater becomes self regulating of maintenance free. Here regulating the steam supply to the vaporizer controls the vapour temperature.

• MOQ 1 Set(s)
• Brand NameVISHWA-FSB (STD)

Film type and continuous sulphur burners with waste heat recovery system for generation of so2 gas for sugar process clarification with waste heat recovery system. - innovative design. - no external steam supply required. - independent vapor generation system. - no sublimation. - negligible maintenance. - most economical

Vishwa' continuous type sulphur burner with waste heat recovery system is used for generation of so2 gas for sulphitation process for sugar factory.

We offer Sulphur Burner. 'Vishwa' Film type Sulphur Burner with waste heat recovery system is used for Cane sugar factory for generation of So2 gas by using waste heat recovery system . There is no need of external 7 Kgcm2 steam is required to melt the raw sulphur. The In-built arrangement of heating system take care of generation of steam for melting . Features of system. 1) No external steam supply required. 2) Saving of Live steam and hence bagasse. 3) In-Built vapor generation system. 4) Most economical

Salient Features  Vertical heat exchanger column with SS tubes.  Digital temperature control Highly reliable, robust & maintenance free. Assured high rangibility & turn down ratio.

Salient features  Efficient mixing of juice, milk of lime and SO 2 gas. High-tech stirrer drive arrangement. Uniform SO 2  gas distribution. Complete absorption of gas.

Salient Features  Optimum Slacking . Convenient Orientation. Low speed mixing. Maximum extraction of lime. Low down time.

The sulphitation process in sugar factory involves adding milk of lime and sulphur dioxide gas to the cane juice. The milk of lime is produced at the lime station by lime slacking. The milk of lime produced so, contains lot of solid materials called as grit, which vary in size. It is necessary to remove this grit which is the responsible for scaling in evaporators, large mud volume at the classifiers, and choking of the lime distribution unit at the sulphitors. 'VISHWA' Lime Grit Classifier is designed to remove the grit of particle size as small as 0.3 mm. It is a high tech classifier having multiplane vibrating screen which is responsible for separation of the grit. Following are the features for 'Vishwa' make 'Lime grit Classifier' OR 'Lime grit Separator. Ultra modern design  Maximum grit separation Pure milk of lime Easy control of lime at Sulphitation Jamming at lime valve is minimized  Easy maintenance

Salient Features  Steam Saving and hence bagasse. Energy Efficient. Auto Electrical Heating backup.