Write a Review
Our Products
Heat Exchangers
2 Products availableProcess Control Systems & Equipment
1 Products availableSeparating Machines
1 Products availableMedical And Industrial Gases
1 Products availableElectrical Panels & Distribution Box
1 Products availableWe are leaders in the market for providing best range of Condensate Recovery System, Based Pressure Control Strainer, On-Off Temperature Control System, PH Control System and Packaged Feed Water Tank System
It is very important to supply dry steam to the equipment. Moisture separator installed at inlet of the pressure reducing station ensures maximum Moisture Separator removal from the steam.
Other Applications: At inlet of the Critical equipments in steam lines like Steam flow meter Moisture Separator, Control valves, inlet of critical process equipments etc. Available Sizes: From 15 NB to 200 NB.
Deaerator head Oxygen or other incondensable gases in the steam system can cause restrict the heat transfer to the process as well as causes corrosion in the steam & condensate system.
So it is very important to remove the oxygen & other gases from the steam system or to ensure that these do not get into the steam system. This can be done by thermal Deaerator Head.
The removal of the gases is achieved by maintaining the highest possible temperature in the feed water tank from where these gases can enter into steam system. We offer specially designed deaerator heads to suit customer's requirement.
Features of Deaerator Head:
Level control system Maintaining the optimum level control system in the feed water tank is very important in order to ensure maximum temperature in feed water tank from condensate recovery & ensure the safety of the boiler.
To achieve this without manual intervention, level control system is used. We offer a customized Level Control Systems for Boiler Feed water tank where hot condensate is preferred & utilized maximum, then hot water from any other sources & last preference to the cold make up water.
This ensures that the energy of hot condensate & hot water from other sources is utilized
The Volfram Tubular Heat Exchanger is used majorly in food and beverage industryfor chilling, heating as well as pasteurization application. The combination of straight as well as corrugated Tubular Heat Exchanger are used which gives the optimum efficiency and maximum output.
Tubular Heat Exchangers have various applications in following industries:
A shell and tube heat exchanger is a class of heat exchanger designs. It is the most common type of heat exchanger in oil refineries and other large chemical processes, and is suited for higher-pressure applications. As its name implies, this type of heat exchanger consists of a shell (a large pressure vessel) with a bundle of tubes inside it. One fluid runs through the tubes, and another fluid flows over the tubes (through the shell) to transfer heat between the two fluids. The set of tubes is called a tube bundle, and may be composed of several types of tubes: plain, longitudinally finned, etc.
Volfram offers Shell and Tube Heat Exchangers with Smooth Tubes and Corrugated Tube through its fixed sized ranges and customized ranges of heat exchangers for applications such as pre -heaters, hot water generators, and condensers, re -boilers. The heat exchangers are designed on the basis of our extensive thermal and mechanical experience acquired over the period of time through successful installation of units.
VOLFRAM offers all type of ASME configurations for all types of applications in Stainless steel construction. VOLFRAM has an entire range of standard heat exchangers in single pass and multi-pass design which helps in quick selection of the heat exchanger to give an optimal and economical solution.
Shell and Tube Heat Exchangers have various applications in following industries:
Condensate Recovery System Significant amounts of energy and resources can be saved by setting up a system to quickly recover and reuse Condensate Recovery System & Flash Steam.
In an indirect heating process only 80% of the steam energy is used for heating & 20% energy comes out in the form of Condensate.
Condensate Recovery pump Significant amounts of energy and resources can be saved by setting up a system to quickly recover and reuse Condensate Recovery Pump & Flash Steam.
In an indirect heating process only 80% of the steam energy is used for heating & 20% energy comes out in the form of Condensate.
Condensate is valuable resource of Heat available in process plant. Recovery of condensate reduces Fuel Consumption significantly by increasing the feed water temperature.
Water charges:Any Condensate Recovery Pump not returned needs to be replaced by fresh water, increasing the fresh water requirement of the plant & its chemical treatment cost.
Reduction in ETP load:Hot Condensate Recovery Pump drained is taken to the ETP which increases the load on ETP. This can be avoided by complete condensate recovery pump.
Maximizing boiler output:As per F & A rating of boiler, hotter the feed water temperature higher will be the steam output from boiler.
Reduction in Blow down Loss:Condensate is pure water, which contains almost no total dissolved solids (TDS). Returning more condensate to the feed-tank reduces the need for blow-down & thus reduces the energy lost from the boiler.
In a close system of steam & condensate, it is very difficult to check whether the steam traps are working or not. Sight glass is a tool for the user for the monitoring of the performance of the equipment.
Application:Available Sizes: 15NB, 25NB, 40NB, 50NB.
Temperature Control System Volfram provides the complete range of customized temperature control solutions and control valves which can fulfill the needs of various process requirements.
In a process plant there are requirements of different temperatures at different processes. It is very important to control & maintain the temperatures as specified in order to:
We also offer PID based Pressure control Strainer for the critical applications where process is very sensitive to steam pressure & has heavy steam loads. This type of Strainer can maintain pressure within + 0.05 bar.
The system consists of Pneumatic control Strainer with Electro-pneumatic positioner, pressure transmitter & PID based pressure controller.
Waste Heat Recovery Systems With day by day rising costs of fuel & in turn utility cost, recovering the waste energy is a basic need of any process industry.
We offer complete customized package solution to recover energy from various waste heat sources in process plants.
Recovering heat from the different sources needs different engineering of the complete system, which involves Selection & designing of:
The selected heat exchanger should be suitable for the particular application The design should be considering the maximum Waste Heat Recovery Systems
With day by day rising costs of fuel & in turn utility cost, recovering the waste energy is a basic need of any process industry.
We offer complete customized package solution to recover energy from various waste heat sources in process plants.
Recovering heat from the different sources needs different engineering of the complete system, TDS Control System which involves Selection & designing of:
VOLFRAM offers high quality Bourdon tube pressure gauges with complete stainless steel body and internals for accurate measurement of pressures, suitable for various media applications.
Application:
Features of Pressure Gauges:
VOLFRAM The model A-10 Pressure Transmitter sensor for general industrial application is not only notable for its compact design, but it also offers excellent quality at an extremely competitive price.
The user can choose between a non-linearity of 0.25% and 0.5 %. A free test protocol provides information on the measuring points recorded during manufacture.
Special features of Pressure Transmitter:
Application of Pressure Transmitter:
Volfram (volfram)
Volfram Systems Pvt. Ltd.
Sr. No. 18, Rutuvihar, 402,
Waranasi Society, Warje,
– 411 058, Pune, Maharashtra - 411052, India
Share us via
