We are one of the recognized names in the industry for designing, keeping in mind the specific requirements of the clients, and providing an array of Electrical Panels some of which are listed below. These panels are made of good quality materials in accordance with industrial quality standards. These find their application in commercial buildings, hospitals, industries, dairies, telecommunications, research laboratories etc.
Synchronizing Panel :
Synchronizing Panel works between two or more different power sources like DG sets to manage power supply. Synchronization helps in making different DG sets behave as a virtual single unit and eliminates subdivision of total load. It helps in transferring load from one unit to another as during service period, so that the unit requiring service can be easily shut off. In this way the critical load need not be interrupted and there is no production loss. During low load we can run any single unit, and synchronize more units as the load increases. This can be manual or automatic.
LT Panel and HT Panel :
LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions. Our LT panels are designed to work with low electricity consumption that makes them cost effective
HT Panel is like LT Panel except that it is used for high tension cables.
APFC (Automatic Power Factor Control) Panels :
These panels are used in commercial buildings and industries where there is fluctuation in voltage and power supply. The electrical load required by a unit depends upon the type of machineries, cooling plants and other devices installed. There is always a possibility of damage of these equipments if power fluctuates. In case of fixed loads they can be safeguarded using capacitors, but in case of varied loads, a mechanism to switch in and switch out the capacitors is required which is basically handled using APFC panels.
PCC (Power Control Center) Panels :
Its basic function is to control power supply to various units and equipments as per their load requirement so that they can work in harmony.
MCC (Motor Control Centre) Panel :
These are effectively used with motors or submersible pumps to provide sufficient protection from overloads and short circuits. These are high on performance, require low maintenance and can withstand extreme temperature variations.
Lighting Control Panels :
We can design and supply Distribution & Lighting Control Panels, which find application in plants for distributing power in the lighting system, keeping in mind the specific requirements of the clients.
VFD Control Panels :
These are designed to control the speed of electric motor and feed pump. They are widely used in drilling, pumping and other large machine applications. The VFD panels are widely used in tube mills, paper mills, extruder plants, rolling Mills, cable industry and CTL Lines. They are even installed in hospitals, business houses and other public places. VFD control panel are designed to match variable speed requirements of a process unit and so are vigorously tested on various speed parameters.
Feeder Pillar Panels :
The feeder pillar panels are used to terminate and distribute the control circuits. These are used in almost all the industries, townships and housing societies to put all the cut-outs together.

We are one of the recognized names in the industry for designing, keeping in mind the specific requirements of the clients, and providing an array of Electrical Panels some of which are listed below. These panels are made of good quality materials in accordance with industrial quality standards. These find their application in commercial buildings, hospitals, industries, dairies, telecommunications, research laboratories etc.
Synchronizing Panel :
Synchronizing Panel works between two or more different power sources like DG sets to manage power supply. Synchronization helps in making different DG sets behave as a virtual single unit and eliminates subdivision of total load. It helps in transferring load from one unit to another as during service period, so that the unit requiring service can be easily shut off. In this way the critical load need not be interrupted and there is no production loss. During low load we can run any single unit, and synchronize more units as the load increases. This can be manual or automatic.
LT Panel and HT Panel :
LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions. Our LT panels are designed to work with low electricity consumption that makes them cost effective
HT Panel is like LT Panel except that it is used for high tension cables.
APFC (Automatic Power Factor Control) Panels :
These panels are used in commercial buildings and industries where there is fluctuation in voltage and power supply. The electrical load required by a unit depends upon the type of machineries, cooling plants and other devices installed. There is always a possibility of damage of these equipments if power fluctuates. In case of fixed loads they can be safeguarded using capacitors, but in case of varied loads, a mechanism to switch in and switch out the capacitors is required which is basically handled using APFC panels.
PCC (Power Control Center) Panels :
Its basic function is to control power supply to various units and equipments as per their load requirement so that they can work in harmony.
MCC (Motor Control Centre) Panel :
These are effectively used with motors or submersible pumps to provide sufficient protection from overloads and short circuits. These are high on performance, require low maintenance and can withstand extreme temperature variations.
Lighting Control Panels :
We can design and supply Distribution & Lighting Control Panels, which find application in plants for distributing power in the lighting system, keeping in mind the specific requirements of the clients.
VFD Control Panels :
These are designed to control the speed of electric motor and feed pump. They are widely used in drilling, pumping and other large machine applications. The VFD panels are widely used in tube mills, paper mills, extruder plants, rolling Mills, cable industry and CTL Lines. They are even installed in hospitals, business houses and other public places. VFD control panel are designed to match variable speed requirements of a process unit and so are vigorously tested on various speed parameters.
Feeder Pillar Panels :
The feeder pillar panels are used to terminate and distribute the control circuits. These are used in almost all the industries, townships and housing societies to put all the cut-outs together.