Air Spray Solution

Ghansoli, Navi Mumbai, Maharashtra

Features of HR 567 Heat Resistant Spray HR 567 Heat Resistant Spray is High heat resistant coating, For all exposed metal surfaces, especially where extreme heat resistance is required, air dries quickly on application to form long lasting finish resistant to surface temperatures reaching as 700C. Rapid drying to a very tough finish Very good resistance to moisture and chemicals good anti-corrosion characteristics Excellent adhesion to composites and aluminium Application of HR 567 Heat Resistant Spray Heat resistant paints are designed to withstand high temperatures of up to 700C, Which makes them ideal for use on fireplaces, chimneys, pipes, engines, exhaust pipes, log-burners and many more metal / metallic items requiring heat proof treatment. Direction of HR 567 Heat Resistant Spray Remove dirt, grease, oil, loose rust and all other surface contaminants by appropriate means. Sand intact coatings to roughen the surface slightly. The surface must be clean and dry during application. Remove cover cap. Shake vigorously for at least one minute after the rattle of mixing ball is heard. Shake frequently during use. Hold can approx. 30 cm from surface. Use back and forth motion keeping can parallel with surface. Ensure that can is in motion when spray button is pressed to avoid runs and sags. Apply several thin layers at a few minutes interval to achieve adequate coating thickness. After use turn can upside down and press spray button for 2 3 seconds to clean valve. Precaution of HR 567 Heat Resistant Spray Contents are Extremely Flammable and Under Pressure, Do not punctured , may explode if heated. Do not apply while equipment is energised, Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurised container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source, live circuits. Harmful in contact with eyes. Prolonged exposure may cause chronic effects. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN Eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations. Storage of HR 567 Heat Resistant Spray Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50C/122 F. Store in a well-ventilated place. Keep container tightly closed. Keep Out of Reach of Children.

Features of HD 1015 - Heavy Duty Mechanical Parts Cleaner Heavy Duty Parts Cleaner is designed to penetrate and effectively dissolve and remove oil, grease, brake fluid, and other soils from all metal parts, heavy machinery, farming equipment, mining equipment, and any other mechanical parts in extremely difficult situation. Low odour properties improve operator working conditions.Will quickly and effectively flush built up grease from chains and slides on forklifts, wire ropes and all types of industrial equipment. Application of HD 1015 - Heavy Duty Mechanical Parts Cleaner The product is designed to be effective in heavy duty cleaning of machine parts, disc & drum brakes and forklift chains, wire ropes, open gears, bearings, valves, sprockets etc. Direction of HD 1015 - Heavy Duty Mechanical Parts Cleaner Shake well before use until the sound of the ball is audible. clean & degrease surface Hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. Repeat spraying whenever necessary. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes. Precaution of HD 1015 - Heavy Duty Mechanical Parts Cleaner Contains gas under pressure do not punctured , may explode if heated. Extremely flammable Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations. Storage of HD 1015 - Heavy Duty Mechanical Parts Cleaner Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50C/122 F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

Features of NDT 103 Non Destructive testing

• Detects Surface defects upto 1 micron width x 30 micron depth on Standard Ni - Cr Test Panel.
• Low halides and Sulphate contents.
• Non - corrosive and non - toxic.
• The quick opertional sequence makes results available immediately.
• Convenient and easy to handle pressurised cans and bulk containers to suit various industrial needs.
• A General purpose, verstile and inexpensive technique.

Environment friendly

CLEANER SPRAY- is an aerosol applied cleaner used as part of the NDT 103rack detection system for pre-use cleaning, also for the easy removal of RMC RED DYE and RMC DEVELOPER Sprays.

• Cuts through dirt, grease and grime
• Zero residue
• Prepares surface for non destructive testing

DEVELOPER SPRAY-is an aerosol applied white powder that is designed to draw the penetrant out of a flaw to enhance the definition. It is used to facilitate detection when used in conjunction with the NDT 103rack detection system.

• Highly absorbent white film for rapid results
• Highlights very fine cracks
• Sharp indication and geometry of defect to the naked eye
• Suitable for pressure testing & leak detection

DYE PENETRANT SPRAY-Dye Penetrant is an aerosol applied dye which can be sprayed from any angle. Used as part of the NDT 103rack detection system.

• Bright red even film
• Highly sensitive dye
• Water washable

Application of NDT 103 Non Destructive testing

Non-destructive inspection system is designed to provide a fast reliable method for visual detection of cracks or flaws which would not normally be visible to the naked eye. Ideal for the inspection of welded joints, castings, forgings etc. non-destructive testing kit includes the cleaner, penetrant and developer spray in a convenient carrypack.

• Cleaner : Stainless Steel, Titanium, Nickel, Carbides, Ceramic and certain plastics, Pressure, Vessels, Pipelines, Heat Exchangers, Casting and Forgings.
• Developer :Aluminum, Magnesium, Brass, Copper, Cast Iron, Steel, Pipelines, Heat, Exchangers, Casting and Forgings, Petrochemical plants, Boilers.
• Dye Penetrant : Pressure Vessels, Pipelines, Heat Exchangers, Casting and Forgings, Petrochemical plants, Boilers and others

Direction of use of NDT 103 Non Destructive testing

• Shake well before use.
• Clean the surface to removed dust with clean cloth.
• Hold the can at least 8 to 12 cm from the surface you are spraying and keep the can upright during use. repeat the same every after every 8-10 operations. wipe off the spatter with a light cloth.
• When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes

Precaution of NDT2 Non Destructive testing

• Contents are Extremely Flammable and Under Pressure, Do Not Puncture
• Prevention : Keep away from heat, sparks, open flames, hot surfaces. No smoking. Avoid
• breathing dust, fume, gas, mist, vapours, spray. Use only outdoors or in a well-ventilated area. do not contaminate water supply. incinerate or store above 50C. Exposure to high temperatures may cause can to burst. Do not place in direct sunlight or near any heat source. Aerosol cans will conduct electricity. Keep away from all live electrical sources including battery terminals, solenoids,
• electrical panels and other electronic components. Failure to observe this warning may result in serious injury from flash fire and/or electrical shock.

First Aid:

• Swallowed Not considered a normal route of entry. Do not induce vomiting. Seek medical
• advice. Avoid giving milk or oils. Avoid giving alcohol.
• Skin Flush skin and hair with running water (and soap if available). Remove any adhering
• solids with industrial skin cleansing cream. Do not use solvents. Seek medical attention in the event of irritation.
• Eyes Immediately hold eyelids apart and flush eye continuously for at least 15 minutes with fresh running water. Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids. Transport to hospital or doctor without delay.
• Inhalation Remove to fresh air. Lay patient down. Keep warm and rested.
• Dispose of empty containers safely. All unused product should be disposed of in conformance with local and HSNO regulations,

Storage of NDT 103 Non Destructive testing

• Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 C/122 F. Store in a well-ventilated place.keep container tightly closed.
• Keep Out of Reach of Children

Features of RIV 2030 highly insulating varnish in convenient aerosol

RIV 2030 It is a highly insulating varnish in convenient aerosol form It is a high gloss red color high temperature flexible chemical resistance coating to Class F winding or electrical apparatus It is specially designed for protection and sealing of insulated surface against deterioration, exposure to oil, moisture, acid and alkaline fumes.

• Excellent Adhesion
• Quick drying
• Protects against moisture and corrosion
• Class F air drying single component.
• Environmental friendly. INSULATING SPRAY aerosol packing is CFC-free.

Application of RIV 2030 highly insulating varnish in convenient aerosol

It can be used for protection of Small field and magnet coils, motor windings, field coils, transformers, armatures, commutator ends, stator windings, ring and frames, bus bars, sealing electrical, switchboard parts and electronic components. motor case interiors, collector rings and shells, field winding of motor starters and generators etc.

Direction of RIV 2030 highly insulating varnish in convenient aerosol

• Shake well before use until the sound of the ball is audible. clean & degrease surface
• Hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying.
• Repeat spraying whenever necessary. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.

Precaution of RIV 2030 highly insulating varnish in convenient aerosol

• Contains gas under pressure do not punctured , may explode if heated.
• Extremely flammable
• Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation.
• May cause drowsiness and dizziness
• Response IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.
• Dispose of contents and/or container according to Federal, State/Provincial and local
• governmental regulations.

Storage of RIV 2030 highly insulating varnish in convenient aerosol

• Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50C/122 F. Store in a well-ventilated place.keep container tightly closed.
• Keep Out of Reach of Children

Features of HD 1014 - Heavy Duty Motor Cleaner

It is a degreasing agent with high dielectric resistance for cleaning electric motors and other equipments. it instantly penetrates and removes dirt, moisture, oil, wax and grease from electrical equipment and machinery to clean and degrease electrical equipment when electrical current exists, this prevents intermittent failure of equipment due to flash-overs or short circuits.

Application of HD 1014 - Electronic and Electrical parts contact cleaner

motor cleaner has been designed for the specific cleaning and degreasing of electric motors, generators, Switch gears, Terminal, air conditioners, fans, transformers and tools. It quickly removes grease, tar, carbon deposits and all dirt characteristic to this kind of equipment

Direction of HD 1014 - Heavy Duty Motor Cleaner

• Shake well before use until the sound of the ball is audible. clean & degrease surface
• Hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying.
• Repeat spraying whenever necessary. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.

Precaution of HD 1014 - Heavy Duty Motor Cleaner

• Contains gas under pressure do not punctured , may explode if heated.
• Extremely flammable
• Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation.
• May cause drowsiness and dizziness
• Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.
• Dispose of contents and/or container according to Federal, State/Provincial and local
• governmental regulations.

Storage of HD 1014 - Heavy Duty Motor Cleaner

• Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50C/122 F. Store in a well-ventilated place.keep container tightly closed.
• Keep Out of Reach of Children

Features of BTC 2021 Battery Terminal Coat Protector Dry

BTC 2021 Battery Terminal Coat Protector Dry is designed to protect battery terminals from corrosion, the leading cause of battery failure, and to maintain the batteries peak performance level. Battery Terminal Protector provides a dry, lead- free protective coating that keeps moisture, salts and road grime from corroding metal contacts. Maximises performance, provides long lasting protection and extends battery life.

 

Application of BTC 2021 Battery Terminal Coat Protector Dry

Protecting battery and cable terminals against leakages, acid sulfation and corrosion. Prevents current losses and enhances battery life Air tight, water proof and acid resistant, anti-sulfation coating. Resistant to heat, gasoline, oil & grease, will not crack or peel when correctly applied on undamaged batteries operating in conditions of medium acidity.

 

Direction of BTC 2021 Battery Terminal Coat Protector Dry

• Shake well can before use.
• Disconnect earth cable to prevent arcing before applying.
• Clean away any existing corrosion with RMC 00 Battery Maintenance. Apply an even coat of RMC 00 Battery Terminal Protector to freshly cleaned site.
• For preventative maintenance, reapply at least every four months.
• When finished spraying, clean valve by turning can upside down and depressing actuator until only propellant escapes.
• Do not use on energized equipment.
• Do not allow can to touch battery terminals.

 

Precaution of BTC 2021 Battery Terminal Coat Protector Dry

• Contents are Extremely Flammable, Contents Under Pressure, Do not punctured. Prevention : Keep spray away from heat, sparks, pilot lights, open flames, etc.
• Do not place in direct sunlight or near any heat source. Aerosol
• cans will conduct electricity. Keep away from all live electrical sources including
• battery terminals, solenoids, electrical panels and other electronic components.
• Failure to observe this warning may result in serious injury from flash fire and/
• electrical shock.
• Harmful by inhallation and avoid contact with skin and eyes
• Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse
• cautiously with water for several minutes. Remove contact lenses, if present and easy
• to do. Continue rinsing. If eye irritation persists: Get medical attention.
• Disposal requirements vary by state and local regulations. All used and unused
• product should be disposed of in conformance with local, state and commonwealth

laws and regulations.

 

Storage of BTC 2021 Battery Terminal Coat Protector Dry

• Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122 °F. Store in a well-ventilated place.keep container tightly closed.
• Keep Out of Reach of Children

Features of NDT 102 Non Destructive testing

• Detects Surface defects upto 1 micron width x 30 micron depth on Standard Ni - Cr Test Panel.
• Low halides and Sulphate contents.
• Non - corrosive and non - toxic.
• The quick opertional sequence makes results available immediately.
• Convenient and easy to handle pressurised cans and bulk containers to suit various industrial needs.
• A General purpose, verstile and inexpensive technique.

Environment friendly

CLEANER SPRAY- is an aerosol applied cleaner used as part of the NDT crack detection system for pre-use cleaning, also for the easy removal of RMC RED DYE and RMC DEVELOPER Sprays.

• Cuts through dirt, grease and grime
• Zero residue
• Prepares surface for non destructive testing

DEVELOPER SPRAY- is an aerosol applied white powder that is designed to draw the penetrant out of a flaw to enhance the definition. It is used to facilitate detection when used in conjunction with the NDT crack detection system.

• Highly absorbent white film for rapid results
• Highlights very fine cracks
• Sharp indication and geometry of defect to the naked eye
• Suitable for pressure testing & leak detection

Dye Penetrant Spray- Dye Penetrant is an aerosol applied dye which can be sprayed from any angle. Used as part of the NDT crack detection system.

• Bright red even film
• Highly sensitive dye
• Water washable

Application of NDT 102 Non Destructive testing

Non-destructive inspection system is designed to provide a fast reliable method for visual detection of cracks or flaws which would not normally be visible to the naked eye. Ideal for the inspection of welded joints, castings, forgings etc. non-destructive testing kit includes the cleaner, penetrant and developer spray in a convenient carrypack.

• Cleaner : Stainless Steel, Titanium, Nickel, Carbides, Ceramic and certain plastics, Pressure, Vessels, Pipelines, Heat Exchangers, Casting and Forgings.
• Developer :Aluminum, Magnesium, Brass, Copper, Cast Iron, Steel, Pipelines, Heat, Exchangers, Casting and Forgings, Petrochemical plants, Boilers.
• Dye Penetrant : Pressure Vessels, Pipelines, Heat Exchangers, Casting and Forgings, Petrochemical plants, Boilers and others

Direction of use of NDT 102 Non Destructive testing

• Shake well before use.
• Clean the surface to removed dust with clean cloth.
• Hold the can at least 8 to 12 cm from the surface you are spraying and keep the can upright during use. repeat the same every after every 8-10 operations. wipe off the spatter with a light cloth.
• When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes

Precaution of NDT 102 Non Destructive testing

• Contents are Extremely Flammable and Under Pressure, Do Not Puncture
• Prevention : Keep away from heat, sparks, open flames, hot surfaces. No smoking. Avoid
• breathing dust, fume, gas, mist, vapours, spray. Use only outdoors or in a well-ventilated area. do not contaminate water supply. incinerate or store above 50C. Exposure to high temperatures may cause can to burst. Do not place in direct sunlight or near any heat source. Aerosol cans will conduct electricity. Keep away from all live electrical sources including battery terminals, solenoids,
• electrical panels and other electronic components. Failure to observe this warning may result in serious injury from flash fire and/or electrical shock.

First Aid :

• Swallowed Not considered a normal route of entry. Do not induce vomiting. Seek medical
• advice. Avoid giving milk or oils. Avoid giving alcohol.
• Skin Flush skin and hair with running water (and soap if available). Remove any adhering
• solids with industrial skin cleansing cream. Do not use solvents. Seek medical attention in the event of irritation.
• Eyes Immediately hold eyelids apart and flush eye continuously for at least 15 minutes with fresh running water. Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids. Transport to hospital or doctor without delay.
• Inhalation Remove to fresh air. Lay patient down. Keep warm and rested.
• Dispose of empty containers safely. All unused product should be disposed of in conformance with local and HSNO regulations,

Storage of NDT 102 Non Destructive testing

• Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 C/122 F. Store in a well-ventilated place.keep container tightly closed.
• Keep Out of Reach of Children

Features of NDT 101 Non Destructive testing Detects Surface defects upto 1 micron width x 30 micron depth on Standard Ni - Cr Test Panel. Low halides and Sulphate contents. Non - corrosive and non - toxic. The quick opertional sequence makes results available immediately. Convenient and easy to handle pressurised cans and bulk containers to suit various industrial needs. A General purpose, verstile and inexpensive technique. Environment friendly CLEANER SPRAY- is an aerosol applied cleaner used as part of the NDT crack detection system for pre-use cleaning, also for the easy removal of ASS RED DYE and ASS DEVELOPER Sprays. Cuts through dirt, grease and grime Zero residue Prepares surface for non destructive testing DEVELOPER SPRAY-is an aerosol applied white powder that is designed to draw the penetrant out of a flaw to enhance the definition. It is used to facilitate detection when used in conjunction with the NDT crack detection system. Highly absorbent white film for rapid results Highlights very fine cracks Sharp indication and geometry of defect to the naked eye Suitable for pressure testing & leak detection DYE PENETRANT SPRAY - Dye Penetrant is an aerosol applied dye which can be sprayed from any angle. Used as part of the NDT crack detection system. Bright red even film Highly sensitive dye Water washable Application of NDT 101 Non Destructive testing Non-destructive inspection system is designed to provide a fast reliable method for visual detection of cracks or flaws which would not normally be visible to the naked eye. Ideal for the inspection of welded joints, castings, forgings etc. non-destructive testing kit includes the cleaner, penetrant and developer spray in a convenient carrypack. Cleaner : Stainless Steel, Titanium, Nickel, Carbides, Ceramic and certain plastics, Pressure, Vessels, Pipelines, Heat Exchangers, Casting and Forgings. Developer :Aluminum, Magnesium, Brass, Copper, Cast Iron, Steel, Pipelines, Heat, Exchangers, Casting and Forgings, Petrochemical plants, Boilers. Dye Penetrant : Pressure Vessels, Pipelines, Heat Exchangers, Casting and Forgings, Petrochemical plants, Boilers and others Direction of use of NDT 101 Non Destructive testing Shake well before use. Clean the surface to removed dust with clean cloth. Hold the can at least 8 to 12 cm from the surface you are spraying and keep the can upright during use. repeat the same every after every 8-10 operations. wipe off the spatter with a light cloth. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes Precaution of NDT 101 Non Destructive testing Contents are Extremely Flammable and Under Pressure, Do Not Puncture Prevention : Keep away from heat, sparks, open flames, hot surfaces. No smoking. Avoid breathing dust, fume, gas, mist, vapours, spray. Use only outdoors or in a well-ventilated area. do not contaminate water supply. incinerate or store above 50C. Exposure to high temperatures may cause can to burst. Do not place in direct sunlight or near any heat source. Aerosol cans will conduct electricity. Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Failure to observe this warning may result in serious injury from flash fire and/or electrical shock. First Aid : Swallowed Not considered a normal route of entry. Do not induce vomiting. Seek medical advice. Avoid giving milk or oils. Avoid giving alcohol. Skin Flush skin and hair with running water (and soap if available). Remove any adhering solids with industrial skin cleansing cream. Do not use solvents. Seek medical attention in the event of irritation. Eyes Immediately hold eyelids apart and flush eye continuously for at least 15 minutes with fresh running water. Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids. Transport to hospital or doctor without delay. Inhalation Remove to fresh air. Lay patient down. Keep warm and rested. Dispose of empty containers safely. All unused product should be disposed of in conformance with local and HSNO regulations, Storage of NDT1 Non Destructive testing Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 C/122 F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

Features of HR 567 Heat Resistant Spray HR 567 Heat Resistant Spray is High heat resistant coating, For all exposed metal surfaces, especially where extreme heat resistance is required, air dries quickly on application to form long lasting finish resistant to surface temperatures reaching as 700C. Rapid drying to a very tough finish Very good resistance to moisture and chemicals good anti-corrosion characteristics Excellent adhesion to composites and aluminium Application of HR 567 Heat Resistant Spray Heat resistant paints are designed to withstand high temperatures of up to 700C, Which makes them ideal for use on fireplaces, chimneys, pipes, engines, exhaust pipes, log-burners and many more metal / metallic items requiring heat proof treatment. Direction of HR 567 Heat Resistant Spray Remove dirt, grease, oil, loose rust and all other surface contaminants by appropriate means. Sand intact coatings to roughen the surface slightly. The surface must be clean and dry during application. Remove cover cap. Shake vigorously for at least one minute after the rattle of mixing ball is heard. Shake frequently during use. Hold can approx. 30 cm from surface. Use back and forth motion keeping can parallel with surface. Ensure that can is in motion when spray button is pressed to avoid runs and sags. Apply several thin layers at a few minutes interval to achieve adequate coating thickness. After use turn can upside down and press spray button for 2 3 seconds to clean valve. Precaution of HR 567 Heat Resistant Spray Contents are Extremely Flammable and Under Pressure, Do not punctured , may explode if heated. Do not apply while equipment is energised, Keep away from all live electrical sources including battery terminals, solenoids, electrical panels and other electronic components. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurised container: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source, live circuits. Harmful in contact with eyes. Prolonged exposure may cause chronic effects. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN Eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations. Storage of HR 567 Heat Resistant Spray Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50C/122 F. Store in a well-ventilated place. Keep container tightly closed. Keep Out of Reach of Children.

features of hd 1015 - heavy duty mechanical parts cleaner heavy duty parts cleaner is designed to penetrate and effectively dissolve and remove oil, grease, brake fluid, and other soils from all metal parts, heavy machinery, farming equipment, mining equipment, and any other mechanical parts in extremely difficult situation. low odour properties improve operator working conditions.will quickly and effectively flush built up grease from chains and slides on forklifts, wire ropes and all types of industrial equipment. application of hd 1015 - heavy duty mechanical parts cleaner the product is designed to be effective in heavy duty cleaning of machine parts, disc & drum brakes and forklift chains, wire ropes, open gears, bearings, valves, sprockets etc. direction of hd 1015 - heavy duty mechanical parts cleaner shake well before use until the sound of the ball is audible. clean & degrease surface hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.protect & mask areas not coated. two light coats is best results better than one heavy coat.coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. repeat spraying whenever necessary. when finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes. precaution of hd 1015 - heavy duty mechanical parts cleaner contains gas under pressure do not punctured , may explode if heated. extremely flammable prevention : wear eye or face protection. keep away from heat, hot surfaces, sparks, open flames and other ignition sources. no smoking. pressurized container: do not pierce or burn, even after use. do not spray on an open flame or other ignition source. use only outdoors or in a well-ventilated area. avoid breathing vapor. wash hands thoroughly after handling. causes serious eye irritation. may cause drowsiness and dizziness response : if inhaled: remove victim to fresh air and keep at rest in a position comfortable for breathing. call a poison center or physician if you feel unwell. if in eyes: rinse cautiously with water for several minutes. remove contact lenses, if present and easy to do. continue rinsing. if eye irritation persists: get medical attention. dispose of contents and/or container according to federal, state/provincial and local governmental regulations. storage of hd 1015 - heavy duty mechanical parts cleaner store locked up. protect from sunlight. do not expose to temperatures exceeding 50c/122 f. store in a well-ventilated place.keep container tightly closed. keep out of reach of children

features of riv 2030 highly insulating varnish in convenient aerosol riv 2030 it is a highly insulating varnish in convenient aerosol form it is a high gloss red color high temperature flexible chemical resistance coating to class f winding or electrical apparatus it is specially designed for protection and sealing of insulated surface against deterioration, exposure to oil, moisture, acid and alkaline fumes. excellent adhesion quick drying protects against moisture and corrosion class f air drying single component. environmental friendly. insulating spray aerosol packing is cfc-free. application of riv 2030 highly insulating varnish in convenient aerosol it can be used for protection of small field and magnet coils, motor windings, field coils, transformers, armatures, commutator ends, stator windings, ring and frames, bus bars, sealing electrical, switchboard parts and electronic components. motor case interiors, collector rings and shells, field winding of motor starters and generators etc. direction of riv 2030 highly insulating varnish in convenient aerosol shake well before use until the sound of the ball is audible. clean & degrease surface hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.protect & mask areas not coated. two light coats is best results better than one heavy coat.coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. repeat spraying whenever necessary. when finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes. precaution of riv 2030 highly insulating varnish in convenient aerosol contains gas under pressure do not punctured , may explode if heated. extremely flammable prevention : wear eye or face protection. keep away from heat, hot surfaces, sparks, open flames and other ignition sources. no smoking. pressurized container: do not pierce or burn, even after use. do not spray on an open flame or other ignition source. use only outdoors or in a well-ventilated area. avoid breathing vapor. wash hands thoroughly after handling. causes serious eye irritation. may cause drowsiness and dizziness response if inhaled: remove victim to fresh air and keep at rest in a position comfortable for breathing. call a poison center or physician if you feel unwell. if in eyes: rinse cautiously with water for several minutes. remove contact lenses, if present and easy to do. continue rinsing. if eye irritation persists: get medical attention. dispose of contents and/or container according to federal, state/provincial and local governmental regulations. storage of riv 2030 highly insulating varnish in convenient aerosol store locked up. protect from sunlight. do not expose to temperatures exceeding 50c/122 f. store in a well-ventilated place.keep container tightly closed. keep out of reach of children

features of hd 1014 - heavy duty motor cleaner it is a degreasing agent with high dielectric resistance for cleaning electric motors and other equipments. it instantly penetrates and removes dirt, moisture, oil, wax and grease from electrical equipment and machinery to clean and degrease electrical equipment when electrical current exists, this prevents intermittent failure of equipment due to flash-overs or short circuits. application of hd 1014 - electronic and electrical parts contact cleaner motor cleaner has been designed for the specific cleaning and degreasing of electric motors, generators, switch gears, terminal, air conditioners, fans, transformers and tools. it quickly removes grease, tar, carbon deposits and all dirt characteristic to this kind of equipment direction of hd 1014 - heavy duty motor cleaner shake well before use until the sound of the ball is audible. clean & degrease surface hold the can at least 10 to 12 cm from the surface you are spraying and keep the can upright during use.protect & mask areas not coated. two light coats is best results better than one heavy coat.coating becomes dry in 20 minutes. make sure the surface is completely dry before using.completed cure takes place in about 24 hours depends upon the humidity. & maintain full pressure on valve while spraying. repeat spraying whenever necessary. when finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes. precaution of hd 1014 - heavy duty motor cleaner contains gas under pressure do not punctured , may explode if heated. extremely flammable prevention : wear eye or face protection. keep away from heat, hot surfaces, sparks, open flames and other ignition sources. no smoking. pressurized container: do not pierce or burn, even after use. do not spray on an open flame or other ignition source. use only outdoors or in a well-ventilated area. avoid breathing vapor. wash hands thoroughly after handling. causes serious eye irritation. may cause drowsiness and dizziness response : if inhaled: remove victim to fresh air and keep at rest in a position comfortable for breathing. call a poison center or physician if you feel unwell. if in eyes: rinse cautiously with water for several minutes. remove contact lenses, if present and easy to do. continue rinsing. if eye irritation persists: get medical attention. dispose of contents and/or container according to federal, state/provincial and local governmental regulations. storage of hd 1014 - heavy duty motor cleaner store locked up. protect from sunlight. do not expose to temperatures exceeding 50c/122 f. store in a well-ventilated place.keep container tightly closed. keep out of reach of children