Amar Valves Industries

Kathwada, Ahmedabad, Gujarat

Single piece design Ball valves are the right ball valve for just about every conceivable application. They are available made from bar stocks sand casted , investment casting in various materials, likes SS 304, SS 304L , SS 316 , SS 316L , IC CF8, IC CF8M, IC CF3, ICCF3M .AMTECH SINGLE PC design are regular exporting valves to Europe, America , Asia and Gulf Countries .Sizes -1/4" to 4"(6 NB TO 100 NB). We manufacture valves from genuine guaranteed raw material with material test certificate , hydraulic test certificates , Mill TC 3.1.b available with all supply. Also , we can provide valves with third party inspection agencies.Technical SpecificationsBuild-up of static electricity can occur as a result of constant rubbing of the ball against the PTFE seats. This can be a potential fire hazard, especially while handling inflammable fluids. Spring-loaded plungers are provided between the stem and the ball. Spark generated by friction between the ball and stem during on and off performance to the ground to prevent the possible risk of fire or explosion.

Two-piece ball valves are some of the most common ball valves used. As the name suggests, the two piece ball valve consists of two pieces, one piece that has one end connection and the body. The second piece fits into the first, holds the trim in place and includes the second end connection. The two piece ball valve has one body joint which means the body is composed of two pieces, hence the name two piece. This 2 piece body allows a larger ball to be installed at the time of manufacture, which makes this a full bore or full port ball valve.Full bore means that the bore hole in the ball has the same inside diameter as that of the piping it is connected to. The advantage is that there is no pressure drop and flow rate is unaffected.They provide a simple on/off flow, as well as the ability to control flow rate by opening and closing to different degrees, this process is called throttling. Quick and easy to install, threaded valves are easy to use and require no tools for installation.

A three piece ball valve is preferred wherever regular cleaning is required. The valve body is composed of 3 separate pieces held together by bolts, which can be easily removed for cleaning and servicing. A unique advantage of the 3 piece valve design is that the ball valve ends can remain threaded into the pipe, while the center section containing the ball can be removed. Three Piece Ball Valves are widely utilized in fluid-handing systems for flow management. Amar Valves Industries Supplies Three Piece Ball Valves to light-duty industries for a proper flow management system. These kinds of ball Valves are appropriate for corrosive applications. they're utilized in Detergent, Pharmaceutical, Chemical, Rubber, Pulp and Paper Plants, Water Treatment Plants, Textile Mills and Food processing Plants to name a few. In general, Three Piece Ball Valves provide several benefits when contrasted with different kinds of valves, they supply superior easy operation, which may maintain and regulate high volume, high and warm temperature flow.

Polypropylene Ball Valves are available in Screw End & Plain Socket End. Polypropylene Ball Valves are available in both type Short Handle & MS Plate Long Handle. These Valves can be used for pipe in Drip Irrigation, for managing water pumping system used for agricultural land & horticulture. Polypropylene Ball Valves can also be used for water supply system in commercial as well as domestic sector. For many industrial applications use of Polypropylene Flanged Valve is done for delivering high work output. These types of valves are high in demand because of its outstanding features which includes resistance against pressure as well as high durability. These valves are made available in different sizes starting from 2", 2", 3" , 4" to match up multipurpose needs of different industries. One of the trusted manufacturers of this valve in the industry is Raj Group. The body of the valve is made out of Poly propylene. The product is easy to handle and comes with a High Pressure Bearing capacity ranging Up to 10 Kg/cm. The product is made available at an affordable price.

Amar Valves Industries offers PTFE lined ball valves in FEP/FPA lining. Ball valves always bidirectional valves. The ball shaft in centre can be optionally connected to a pneumatic/electric actuator over an adapter or equipped with a manually operated lever. Ball is sealed in the PTFE lined body with exchangeable seat rings PTFE . The ball shaft is sealed with a maintenance-free. Fail-safe position Depending on the version of the single-acting rotary actuator, the ball valve has two fail-safe positions which become effective when the actuator is relieved of pressure as well as when the supply air fails: Control valve CLOSED without supply air The ball valve closes when the supply air fails when single acting actuator.But in Double acting actuator valves required air supply to pen and close valve each time. We have variety of materials of construction, two piece design valves, ASA 150#, PN10, PN 16.

We are manufacturer of Butterfly Valve, Butterfly Valves is really a valve, which may be useful for identifying or managing movement. The actual final product will take are any disk. Functioning is similar to that of the ball valve that allows with regard to fast turn off. These types of valves are generally favored because they are lacking in expense along with other vale styles in addition to getting lighter in weight, which means a smaller amount help is necessary. The particular butterfly is a metallic disk installed on a Fly fishing rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway.

Amar Valve Industries manufactures a comprehensive range of Aluminium Butterfly valve in sizes 40mmto 200mm and in ASME classes-150. original cross-sectionally S-shaped valve discs with spherical surface evenly make tight contact with rubber liners for excellent sealing performance with reduced operating torque. Thorough 360 shut-off mechanism helps extend service life of rubber liners.

Polypropylene Butterfly Valves incorporate many features of our industrial valve, yet the all Polypropylene construction and EPDM liner make this valve the perfect choice for water and light industrial applications. The special trapezoid shape of the liner and serrated body cavity guarantee a bubble tight seal while keeping break-away torque at an absolute minimum. This versatile valve features double self-lubricating seals, direct actuator mount capability, or the option of either a lever handle or gear box.

The disc is mounted in a nylon bushing, which allows it to move slightly both horisontally and vertically to close completely tight also in case of minor impurities in the seat. The seat is placed in a 20 angle providing tightness even at low backpressure. The hinge is made of acid-resistant stainless steel and is firmly tightened around the shaft with bolts to eliminate play and thus to ensure durability. Where limited space is available, the hinge can be placed in reverse position. It is utilized to stop piping and to prevent backflow. Backflow happens when the substance in the pipe flows the other way when the valve is shut. There are numerous types of this sort of valves, for example, ball check valves, stop-check valve, cone check valves, and disk check valve et cetera.

The disc is mounted in a nylon bushing, which allows it to move slightly both horisontally and vertically to close completely tight also in case of minor impurities in the seat. The seat is placed in a 20 angle providing tightness even at low backpressure. The hinge is made of acid-resistant stainless steel and is firmly tightened around the shaft with bolts to eliminate play and thus to ensure durability. Where limited space is available, the hinge can be placed in reverse position. It is utilized to stop piping and to prevent backflow. Backflow happens when the substance in the pipe flows the other way when the valve is shut. There are numerous types of this sort of valves, for example, ball check valves, stop-check valve, cone check valves, and disk check valve et cetera.

Single piece design Ball valves are the right ball valve for just about every conceivable application. They are available made from bar stocks sand casted , investment casting in various materials, likes SS 304, SS 304L , SS 316 , SS 316L , IC CF8, IC CF8M, IC CF3, ICCF3M .AMTECH SINGLE PC design are regular exporting valves to Europe, America , Asia and Gulf Countries .Sizes -1/4" to 4"(6 NB TO 100 NB). We manufacture valves from genuine guaranteed raw material with material test certificate , hydraulic test certificates , Mill TC 3.1.b available with all supply. Also , we can provide valves with third party inspection agencies.

Where the amount of material to be removed from the flow is relatively small, resulting in long intervals between screen cleanings, the strainer screen is manually cleaned by shutting down the line and removing the strainer cap. For applications with heavier dirt loading, Y-Strainers can be fitted with a "blow-off" connection that permits the screen to be cleaned without removing it from the strainer body.

Amar Valves Industries design, manufacture and supply Tee Strainers in both horizontal and vertical configurations. Tee strainers are designed to remove foreign particles from pipeline. Tee Type Strainers are a low cost solution to large nominal bore straining requirements. Delta Tee strainers protect pipeline equipment from foreign matter present in liquids. Tee strainers are most commonly supplied with a range of graded filtration levels to ensure that the clean liquid flows downstream.

Valves are sorted into two kinds, the stop valves, which gives an on, off or fractionary on setting, and also check valves, which stops the flow of fluid in just a solitary heading. A globe valve has a place with the best valve family. These valves resemble their description. Their valve body is gathered and is made together of two particular parts, which are separated by a plate that closes or opens. Not at all like the other valves, this is more mind boggling on the grounds that it is comprised of a cap, body, stem, plug, seat ring and cage.

There are two main categories of diaphragm valves: one type seals over a "weir" (saddle) and the other (sometimes called a "full bore or straight-through" valve) seals over a seat. In general, straight-through diaphragm valves are used in on-off applications and weir-type diaphragm valves are used for control or throttling applications. While diaphragm valves usually come in two-port forms (2/2-way diaphragm valve), they can also come with three ports (3/2-way diaphragm valves also called T-valves) and more (so called block-valves). When more than three ports are included, they generally require more than one diaphragm seat; however, special dual actuators can handle more ports with one membrane.

CS / SS made bodies with Toughened borosilicate Glass Windows and standard units in flanged / threaded connections provide immunity at higher temperature & pressures. These offer a quick, reliable and inexpensive way to affirm flow rate and direction, and monitor color and clarity in fluid lines. When a problem occurs at certain points along the industrial process line, Sight Flow indicators are used to visually monitor and determine the flow of fluids. These affordable and easy-to-operate devices are installed directly in the process line and allow operators to qualitatively observe flow rate, direction, color and clarity. The readings are then viewed through a glass viewing lens. There are two ways to deploy Sight Flow Indicators

We make Our Pneumatic Ball Valve in to 14 with three end connection Screwed End, Flanged End, and Socket Weld so complete solution for Industry and Users. Aira Euro Automation design and manufacture a range of high integrity instrumentation Pneumatic Ball valves for worldwide applications, yes we supply worldwide as per customer requirement and their drawing.

Pneumatic Air Butterfly Valves are generally used for liquid and slurry materials. These are very popular in the valve industry because of its easy to use and simple mechanism. Pneumatic Butterfly Valves are very useful to control highly inflammable liquids like petro-chemicals, Oil, and Gas. It is operated by Pneumatic which allows fast functionality and safe from fire and electric short circuits. So it is an electricity efficient operated valve with the lowest cost.

We manufacture our products only high quality graded materials and we also follow API standard criteria in making our products so we gain API 609 Certificate for Butterfly Valve and also we got approvals from ONGC, LLOYDS, BHEL, Indian Navy and many more organizations. We always ready to welcome third party inspection for our products, because we have to pass through every unit by our Quality team, they tested our products in the lab and after that, we delivered it to our valuable customers

Pneumatic Butterfly valve works on the simple mechanism and easy to use so it has low maintenance, these valves are fitted in mid of fluid flow. There is a disc connected to a center rod, which rotates the disc quarterly to pass through to open and close. This metal disc called Butterfly, it rotates a quarter turn to allow fluid to pass indefinitely and so on the slow opening valve will reduce the flow and the turning the disc to close the valve and flow. This valve is operated by pressurized air which is controlled by a pneumatic actuator that is fixed on it. So there is nobody needs to operate but pneumatic actuator operates this valve too fast and easily with the lowest cost and safety.

Angle control valves are used as mixing and a distributive controller for many applications such as coal and distributive control, polymers, salt and brine, gasification or any high-pressure process of acid leaching. They are mainly used to control pressure and regulate flow. Our angle control valves are ideal equipment for any type of operating conditions which has issues of high pressure, vibration, temperature drops or high flow rates. Asten has developed any types of angle control valves for different applications. Each valve made for some specific characteristics tailored to control specific process elements.

The pneumatic control signals are traditionally based on a pressure range of 3-15psi (0.2-1.0 bar), or more commonly now, an electrical signal of 4-20mA for industry, or 0-10V for HVAC systems. Electrical control now often includes a "Smart" communication signal superimposed on the 4-20mA control current, such that the health and verification of the valve position can be signalled back to the controller. The HART, Fieldbus Foundation, and Profibus are the most common protocols.

We have a dedicated and hardworking team of engineers who are always trying to make safer and secure valves for the industries and also for the workers safety. We use high-quality graded materials that build trust in our customers resulting in outstanding levels of customer satisfaction. Our valves are available in different materials along with pressure and temperature ratings to suit the customer-specific applications. Our valves can sustain both High and low Temperature media and are suitable for such environments. We make sure to manufacture our valves exactly as per our customers requirements & demands

An MOV is a combination of two separate devices, usually provided by two separate manufacturers. Valve Assembly. a mechanical device to optimize a desired fluid control function, such as isolation or throttling. Actuator. an electrical/mechanical device used to position a valve assembly from a remote location.

A plate or disc is positioned in the center of the pipe. The disc has a rod passing through it that is connected to an actuator on the outside of the actuated butterfly valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.

A plate or disc is positioned in the center of the pipe. The disc has a rod passing through it that is connected to an actuator on the outside of the actuated butterfly valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.

These kind of valves and motors are generally used in applications where the control of a fluid water temperature or the amount of flow (GPM) in the connected system piping is desired. Modulating control valves typically respond faster than that of floating action type valves. A two-way control valve is most often used for on/off zone/flow control. However, two-way control valves with characterized design can be used for modulating purposes also. Many readers will be familiar with using two-way control valves for zone/flow control purposes, so lets look at an example of a piping option using a two-way characterized valve for fluid temperature control purposes