Being a reputed Manufacturer and Supplier, we are offering a quality range of Antique Cem Bond Waterproofing Adhesive (AW+111) from morbi, Gujarat. Waterproofing Adhesive is precisely formulated by using waterproofing compounds. It is an integral liquid water proofing compound for concrete & plaster. Our Waterproofing Adhesive makes concrete cohesive and available with us in different packaging standards.

Description : Antique Cem Bond AW+111 is specially formulated integral liquid waterproofing compound composed of surface active. Plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation.

Areas of Application Waterproofing of concrete and sand-cement mortars used in

•  Basements
•  Roof slabs and screeds
•  Water tanks & water retaining structures
•  External plastering
•  Bathrooms and balconies
•  Sumps and drains

Features & Benefits :

•  Corrosion resistant - Makes concrete more cohesive, hence protects steel better against corrosion
•  Compatibility – Being a liquid, easily dispersible & compatible with concrete/mortar mixes.
•  Permeability – It reduces the permeability of water into concrete.
•  Strength – The setting time and compressive strength of the concrete remains within the specification limits.
•  Shrinkage – Reduces shrinkage crack development in plaster & concrete.
•  Workability – Improves workability of freshly mixed cement concrete.
•  Durability – Increases durability by improving waterproofing of concrete.

Method of Application :

•  Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1–2 minutes.
•  Start addition of 75–80% mixing water & mix for 2-3 minutes.
•  Antique Cem Bond AW+111 is added as per the recommended dosage into the remaining mixing / gauging water, then add to concrete mixer & mix for another 2 minutes.
•  Place the concrete or apply plaster, as needed .
•  Cure the applied mortar or concrete as per good construction practices.

Precautions & Limitations :

• Do not add Antique Cem Bond AW+111 directly to dry cement & aggregate mix.
• Maintain water-cement ratio as low as possible.
• Do not increase the dosage of Antique Cem Bond AW+111 than the recommendation.

 
Dosage : 200 ml per 50 kg bag of cement

Packing : 200 ml, 1, 5 , 20 & 200 liter

Shelf Life & Storage :

•  Shelf life is 12 months from the date of manufacturing in unopened conditions.
•  Store in a cool & dry place.

Health & Safety Precautions :

•  Use rubber hand gloves & safety goggles, while using Antique Cem Bond AW+111.
•  In case of contact with skin, wash with plenty of water.
•  Keep out of reach of children.

We are counted among the trustworthy Manufacturers and Suppliers of Antique Platinum Adhesive (white) from morbi, Gujarat. These adhesives are manufactured by using qualitative raw compounds under the strict guidance of industry professionals. Our White Platinum Adhesives find their applications for both interior and exterior installations, which includes under water applications for fixing tiles, marble etc. Platinum Adhesive is known for their workability and high bonding strength.

Description : The ultimate one-step, polymer modified, thin-set mortar for interior and exterior installation of ceramic tile, stone, quarry tile, pavers and brick. Antique Platinum Adhesive , designed to just mix with water, has a long open time with unsurpassed adhesion and workability.

Uses : Excellent for exterior and underwater applications, Like for fixing swimming pool tiles, marble, granite and all kind of ceramic tiles.

Advantages :

• Exceeds Shear Bond Strength Requirements.
• Ultimate adhesion for porcelain and glass tiles.
• Superior for exterior and submerged applications.
• High shear bond strength.
• Smooth creamy formula.
• See limitations.

Suitable Substrates :

• Concrete / Masonry .
• Concrete block .
• Cement mortar beds .
• Non-water soluble cut-back adhesive*
• Existing ceramic tile and stone

Interior use only : Consult cement backer board manufacturer for specific installation recommendations and to verify acceptability for exterior use.

Approximate Coverage :

• 55–60sft per 20kg bag with 1/4" x 1/4" (6 mm x 6 mm) notched trowel.
• Coverage will vary depending on trowel notch size, type and size of tile and substrate.

Shelf Life :

• Factory sealed containers of this product are guaranteed to be of first quality for one (1) yearif stored off the ground in a dry area.
• High humidity will reduce the shelf life of bagged product.

Packaging : 1kg, 20kg bag

Color : White

Limitations :

• Not for use directly over particle board, luan, Masonite® or hardwood floors.
• Adhesives/mastics, mortars and grouts for ceramic tile, pavers, brick and stone are not replacements for waterproofing membranes. When a waterproofing membrane is required, use a Antique Platinum Adhesive Waterproofing Membrane.

Note : Surfaces must be structurally sound, stable and rigid enough to support ceramic/stone tile, thin brick and similar finishes. Substrate deflection under all live, dead and impact loads, including concentrated loads, must not exceed L/360 for thin bed ceramic tile/brick installations or L/480 for thin bed stone installations where L=span length.

Cautions :

• Consult MSDS for more safety information.
• Some marbles and other stone have low flexural strength and may not be suitable for installation over wood floors.
• During cold weather, protect finished work from traffic until fully cured.
• Contains portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.
• Wait 14 days after the final grouting period before filing water features with water at 70°F (21°C)
• Do Not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas.
• Keep out of reach of children.

 
Specifications subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation methods and site conditions.

Installation : Surface Preparation : All surfaces should be between 40°F (14°C) and 90°F (32°C) and structurally sound, clean and free of all dirt, oil, grease, paint, concrete sealers or curing compounds. Rough or uneven concrete surfaces should be made smooth with Antique Platinum Adhesive Latex Portland Cement Underlayment to provide a wood float (or better) finish. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off. Installation may be made on a damp surface. Concrete slabs must be plumb and true to within 1/4" (6 mm) in 10 ft (3 m).

Note : Antique Platinum Adhesive does not require a minimum cure time for concrete slabs. Expansion joints shall be provided through the tile work from all construction or expansion joints in the substrate. Follow ANSI specification A108.01-3.7 “Requirements for Movement Joints: Preparations by Other Trades” or TCNA detail EJ-171 “Movement Joints—Vertical & Horizontal”. Do not cover expansion joints with mortar.

• Installer must verify that deflection under all live, dead and impact
• L/360 for ceramic tile and brick or L/480 for stone installations where
• L=span length.

Mixing : Place clean, potable water into a clean pail. Add Antique Platinum Adhesive. Use approximately 5-5.5 litres of water for 20kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowelable consistency. Allow mortar to slake for 5–10 minutes. Remix with out adding any more water or powder. During use, stir occasionally to keep mix fluffy. Do Not temper with water.

Application : Apply Antique Platinum Adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side.

Note : Use proper sized notched trowel to ensure full bedding of the tile. Spread as much mortar as can be
covered with tile in 15–20 minutes. Back butter large tiles >8" x 8" (>200 mm x 200 mm) to provide full bedding and firm support. Place tiles into wet, sticky mortar and beat in using a beating block and rubber mallet to embed tile and adjust level. Check mortar for complete coverage by periodically removing a tile and inspecting bedding mortar transfer onto back of tile. If mortar is skinned over (not sticky), remove and replace with fresh mortar.

Grouting : Grout the installation after a minimum of 24 hours curing time at 70^oF (21^oC). Grout with Antique TG Silver Sanded Grout or Antique TG Golden Unsanded Grout mixed & Antique Platinum Grout Admix Plus. For maximum stain resistance use Antique Platinum Adhesive Stain free Grout for Floor N’ Wall.

Maintenance : Antique Platinum Adhesive grouts require routine cleaning with a neutral pH soap and water. All other Antique Platinum Adhesive materials require no maintenance but installation performance and durability may depend on properly maintaining products supplied by other manufacturers.

Warranty : Antique Designer Tiles warrants that Antique Platinum Adhesive is free from manufacturing defects and will not break down, deteriorate or disintegrate under normal usage for a period of one (1) year from date of purchase subject to the terms and conditions stated in Antique Platinum Adhesive Product Warranty.

Owing to our rich industrial experience and rich knowledge, we are engaged in manufacturing and supplying of Super Bond Waterproofing Adhesive from Surat, Gujarat. Our Waterproofing Adhesives are manufactured by using high quality compounds in line with set quality norms. We can make available our Waterproofing Adhesive in varied specifications as per buyer’s need and that too at nominal rates.

We are recognized Manufacturer and Supplier of Antique Flexi Bond Waterproofing Adhesive from Surat, Gujarat. Waterproofing Adhesive, that we offer, is made to provide protection for concrete from seawater. Due to its long lasting effects and quality features, our Waterproofing Adhesives are highly appreciated. Buy from us Waterproofing Adhesive in different quantity and packaging at unbeatable market rates. We assure safe and timely deliveries.

Features & Benefits :

• Waterproofing - Exceptionally good waterproofing.
• Ease of application - Cold applied, bituminous emulsion material. Easily applied by brush or mop.
• Durability - Forms relatively thick (1.2-1.5 mm) film providing excellent impermeable and durable membrane.
• Movement accommodation - Polymer modified hence forms flexible film. Also accommodates thermal stresses in slab due to variation in temperature.
• Reinforcement – Higher reinforcement can be induced with polyester fibre sheet between the coats.
• Self priming – No separate or additional primer is required.

Method of Application :

• Surface Preparation :
  
  • Surface for treatment must be thoroughly cleaned of all laitance, loose material, oil, grease, etc.
  • Mechanical means such as wire brushing & shot blasting can be used.
  • Finally vacuum cleaning of all loose solids and liquids can be done if required.
  • All surface cracks up to 5 mm width should be filled up with Antique Non Shink Crack-x.
  • Cracks more than 5 mm and all separation gaps should be filled up with Antique Flexi Bond URP Modified Adhesive as specified.

• Application :
  
  • Apply Three coats directly by brush or mop and dilute Antique Seal - 115 with three part of water & one part of Antique Seal - 115 powder.
  • Apply 2nd & 3rd coat in gapes of two or three hours.

• Cleaning : Tools & equipments should be cleaned with potable water immediately after use. Cured material can be cleaned by scrapping

 
Precautions & Limitations :

• Dilute with water for application.
• Not recommended for areas larger than 2000 sq. ft.
• Always protect the coating with proper and appropriate screeding. Do not keep it exposed to UV

Coverage :

• 1kg meterial gives coverage 10 to 15 sq. ft.(Three coats)
• Coverage may vary depending upon the texture and porosity of the surface

Packaging - 1, 5kg

Shelf Life & Storage :

• Shelf life is 12 months from the date of manufacturing.
• Store in a cool & dry place. Keep away from direct sun light

Health & Safety Precautions :

• During application wear protective clothing, gloves and eye goggles during application. Avoid product to contact eyes and skin.
• Skin Contact : Wash immediately with plenty of clean water.
• Eye contact : In the event of eye contact splash plenty of clean water immediately and seek medical advice.

We are among the trusted Manufacturers and Suppliers of Super Bond Waterproofing Adhesive (SPW+101) from Surat, Gujarat. Waterproofing Adhesives are precisely processed at our production house. The product is suitable for performing plasticizing actions and provides cohesiveness and waterproofing to cement concrete, mortar etc. We provide Waterproofing Adhesive in air sealed packaging to keep it free from moisture. Customers can contact us for purchasing Waterproofing Adhesive at market leading rates.

Description : Antique Super Bond - SPW+101 (Add Mixture) is specially formulated additive composed of cement compatible, plastisizing agent, polymers & additives. It is used as a waterproofing additive with an additional benefits of plastisizing action, cohesive mix & waterproofing to cement concrete / mortar / plasters. It improves the workability, compressive strength than control & integral waterproofing properties of cement concrete & plasters after curing.

Areas of Application Waterproofing of concrete and sand-cement mortars used in :

• Waterproofing of concrete and sand-cement mortar used in
• Basements,
• Roof slabs and screeds,
• Water tanks & water retaining structures,
• External plastering,
• Bathrooms and balconies,
• Sumps and drains

Features & Benefits :

• Compatibility - Being a liquid, easily dispersible & compatible with concrete / mortar mixes.
• Cohesiveness - Makes the concrete/mortar more cohesive in low W/C ratio, hence no bleeding & segregation.
• Durability - Increases durability, by improving integral waterproofing of concrete.
• Breathing – It retains the breathing efficiency of concrete.
• Permeability – It reduces the permeability of water into concrete by blocking the capillaries.
• Economics – It is an economical additive as compare to other waterproofing materials.
• Workability – Improves workability of freshly mix cement concrete.
• Water reduction – W/C reduction is possible upto 8%, which improves the cuing properties of concrete.
• Strength – Increases the strength of the concrete than control mix.
• Shrinkage - Reduces shrinkage crack development in plaster & concrete.

Method of Application :

• Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1–2 minutes.
• Start addition of 75 – 80% mixing water & mix for 2-3 minutes.
• Antique Super Bond - SPW+101 (Add Mixture) is added as per the recommended dosage into the remaining mixing / gauzing water, then add to concrete mixer & mix for another 2 minutes.
• Discharge the concrete / plaster for application.
• Cure the applied mortar or concrete as per good construction practices.

Precautions & Limitations :

• Do not add Antique Super Bond - SPW+101 (Add Mixture) to dry cement & aggregate mix.
• Maintain water-cement ratio as low as possible (< 0.50).
• Do not increase the dosage of Antique Super Bond - SPW+101 (Add Mixture) than recommendation.

 
Dosage : 100ml per 50Kgs bag of cement.

Packaging : 1, 5 , 20, 200 liters

Shelf Life & Storage :

• Shelf life is 12 months from the date of manufacturing in unopened condition.
• Store in a cool & dry place.

Health & Safety Precautions :

• Use rubber hand gloves & safety goggles, while using Antique Super Bond - SPW+101 (Add Mixture).
• In case of contact with skin, wash with plenty of water.
• Keep out of reach of children’s.