The shank of a normal boring bar is made of hardened steel, but as the LD ratio increases, you can switch to material that reduces the vibrations. Like solid Tungsten Carbide bars. The ability to resist deflection increases as the coefficient of elasticity increases, and Tungsten Carbide has 3 times the coefficient of elasticity of steel. There is also carbide reinforced steel, which is a metal matrix composite (MMC). This is steel with Titanium Carbide (TiC) particles embedded in it. A damped bar is a hollow bar with a vibration damping mechanism in it.

Tooling comes in different sizes: NMTB-25, 30, 35, 40, 45, 50 and 60. NMTB-25 is the smallest, used on small machines, while NMTB-60 is the largest. For a single taper type, the different sizes are scaled versions of the same basic shape.

A floating tap holder does the same thing. The machine is controlling the Z-axis rigidly, but the tap holder has a float that allows the tap to be pulled in or out at a feed rate that is proportional to the spindle speed and pitch. It allows the tap to move axially independent of the machines axis.

Inserts are known by an ISO naming convention that describes their shape and size. Each alphabet and number in the name signifies an aspect of the inserts shape or size. E.g., the first
alphabet is the shape, while the last two numbers are the nose radius.

The tool manufacturers catalog recommends the cutting speed based on the tool material, workpiece material and operation. In the CNC program we however write the RPM. This equation calculates the RPM N from the cutting speed V in meters per minute (mmin)and the tool diameter D (the 1000 in the numerator meters to mm).

Plain tungsten carbide is grey, and various other colours are the result of the coating material. If the insert has multiple coatings, the colour is that of the topmost coating.

A normal tool is clamped by inserting it in a slot in the turret and tightening screws to hold it firmly. While doing this, care must be taken to seat the holder properly against available butting surfaces. Finally, the tool offsets must be taken by touching the part or taking skin cuts. The whole process can take 5 to 10 minutes.

Gray Cast Iron has extremely high damping capacity, and is therefore the preferred material for machine tool beds, tables, columns, etc. (as also engine cylinder blocks, for the same reason).

Software products for cnc machining increase your profits by reducing cycle time, machine down time, accidents and part rejections. They are designed to be used by operators, and typically have a low training time of a few hours.

Software products for cnc machining increase your profits by reducing cycle time, machine down time, accidents and part rejections. They are designed to be used by operators, and typically have a low training time of a few hours.

Software products for cnc machining increase your profits by reducing cycle time, machine down time, accidents and part rejections. They are designed to be used by operators, and typically have a low training time of a few hours.

Software products for cnc machining increase your profits by reducing cycle time, machine down time, accidents and part rejections. They are designed to be used by operators, and typically have a low training time of a few hours.

We are offering cnc program simulation software.
Cam lab is a set of software designed to make students proficient in all aspects of cnc machining, to make your students industry-ready. The same bundle of products is available for in-house training institutes of industries, as proficnc.

The shank of a normal boring bar is made of hardened steel, but as the LD ratio increases, you can switch to material that reduces the vibrations. Like solid Tungsten Carbide bars. The ability to resist deflection increases as the coefficient of elasticity increases, and Tungsten Carbide has 3 times the coefficient of elasticity of steel. There is also carbide reinforced steel, which is a metal matrix composite (MMC). This is steel with Titanium Carbide (TiC) particles embedded in it. A damped bar is a hollow bar with a vibration damping mechanism in it.

Tooling comes in different sizes: NMTB-25, 30, 35, 40, 45, 50 and 60. NMTB-25 is the smallest, used on small machines, while NMTB-60 is the largest. For a single taper type, the different sizes are scaled versions of the same basic shape.

A floating tap holder does the same thing. The machine is controlling the Z-axis rigidly, but the tap holder has a float that allows the tap to be pulled in or out at a feed rate that is proportional to the spindle speed and pitch. It allows the tap to move axially independent of the machines axis.

Inserts are known by an ISO naming convention that describes their shape and size. Each alphabet and number in the name signifies an aspect of the inserts shape or size. E.g., the firstalphabet is the shape, while the last two numbers are the nose radius.

The tool manufacturers catalog recommends the cutting speed based on the tool material, workpiece material and operation. In the CNC program we however write the RPM. This equation calculates the RPM N from the cutting speed V in meters per minute (mmin)and the tool diameter D (the 1000 in the numerator meters to mm).

Plain tungsten carbide is grey, and various other colours are the result of the coating material. If the insert has multiple coatings, the colour is that of the topmost coating.

A normal tool is clamped by inserting it in a slot in the turret and tightening screws to hold it firmly. While doing this, care must be taken to seat the holder properly against available butting surfaces. Finally, the tool offsets must be taken by touching the part or taking skin cuts. The whole process can take 5 to 10 minutes.

Gray Cast Iron has extremely high damping capacity, and is therefore the preferred material for machine tool beds, tables, columns, etc. (as also engine cylinder blocks, for the same reason).

Software products for cnc machining increase your profits by reducing cycle time, machine down time, accidents and part rejections. They are designed to be used by operators, and typically have a low training time of a few hours.

Software products for cnc machining increase your profits by reducing cycle time, machine down time, accidents and part rejections. They are designed to be used by operators, and typically have a low training time of a few hours.

Software products for cnc machining increase your profits by reducing cycle time, machine down time, accidents and part rejections. They are designed to be used by operators, and typically have a low training time of a few hours.

Software products for cnc machining increase your profits by reducing cycle time, machine down time, accidents and part rejections. They are designed to be used by operators, and typically have a low training time of a few hours.

We are offering cnc program simulation software.Cam lab is a set of software designed to make students proficient in all aspects of cnc machining, to make your students industry-ready. The same bundle of products is available for in-house training institutes of industries, as proficnc.