Introducing century's metal marker: metal marker is a permanent marker for making weather proof marking for industrial purpose. The markings made by the marker wont chip/peel/fade or rub off and it can withstand heat and weathering under adverse.. Read More
Century’s Pump-type Metal Marker is unique marking device for permanent & fade-proof marking on any surface. Its an industrial grade ball-point marker which are bright, opaque & weather-proof. It has a rigid aluminum body making it difficult to break, puncture or leak. It also has a rubber valve at the bottom for smooth ink flow. When the valve is pumped it compresses ink towards a fine ball point for smooth flow and easy writing. The markings made by the marker wont chip/peel/fade or rub off and it can withstand heat and weathering under adverse conditions. It has special viscous ink formulation similar to paint which remains permanent on steel, alloys, metals, concrete, glass, rubber, wood & even plastics. It can mark on wet, dry, dusty, oily, greasy & even extremely rough surfaces with ease. Advantages: Viscous ink makes Permanent, Bright & Opaque Markings on all Surfaces including metals, steel, glass, rubber, wood, concrete etc. Hard Aluminum body makes it difficult to break, puncture or leak compared to other tube markers. Rubber valve at bottom makes it very easy to use with continuous ink flow. Zero Wastage compared to Tube type markers. Stainless steel tip with roller ball point enables easy & smooth markings on Wet, Oily, Dry, Greasy & Extremely Rough Surfaces. 60 ml ink content (5-6 times of conventional paint markers) Direction of use: Remove Cap. For cold start press the rubber ball/valve 4-5 times at the bottom for ink flow at the tip. Mark vertically at 90-degree angle & ensure the ball presses the surface for smooth ink flow. As pressure reduces, press the rubber valve 2-3 times to continue writing. Do not press the rubber bulb when not in use as it will lead to increase ink pressure. Clean the tip & put the cap back on when after each use. Caution: Harmful if swallowed or intentional inhalation. Avoid contact with eyes. Keep away from open flame. Please test before use.
Century’s Everon Pen is a fine tip fabric marker used in the textile industry & laboratories for shrinkage testing of fabrics. It has a hard aluminum body filled with ink & a rubber valve at the bottom, when pumped slightly pushes ink towards a fine ball point for sharp and fine markings. It is widely used in textile laboratories and mills to check for dimensional stability (shrinkage) of fabrics with a slotted template after washing and processing on fabrics. It is similar to dalo texpen in many parts of the world. It comes with two type of tips plastic (1.5 mm) & stainless steel (1.2 mm). Ink content: 30 ml Advantages: Hard Aluminum body to avoid breakage, leakage & puncture. East to use & smooth ink flow due to rubber valve at bottom. Fine-tip enables the marker to fit inside the slotted templates for shrinkage testing of fabrics. Markings remain permanent even after dyeing, bleaching, washing & other finishing processes. Works on all fabrics synthetic, cotton, denim, wool, polyester, linen, knitted etc. Direction of Use: Remove Cap. For cold start press the rubber ball/valve 4-5 times at the bottom for ink flow at the tip. Mark vertically at 90-degree angle & ensure the ball presses the surface for smooth ink flow. As pressure reduces, press the rubber valve 2-3 times to continue writing. Do not press the rubber bulb when not in use as it will lead to increase ink pressure. Clean the tip & put the cap back on when after each use. Caution: Harmful if swallowed or intentional inhalation. Avoid contact with eyes. Keep away from open flame. Test before use.
Century’s Tex Marker is a collapsible aluminum writing device filled with ink used for marking on fabric samples for identification. It is used by textile mills & processing houses before dyeing and finishing processes of grey fabric for identification, quality control, shrinkage, pilferage etc. The marking remain permanent, bright & opaque even after the dyeing & finishing processes are completed. It is widely used in textile industry for dyeing, bleaching, hosiery, knitting, scouring & weaving processes. Advantages: Bright & Opaque markings on all kinds of fabrics including cotton, denims, polyester, wool etc. Permanent, Heat-Proof, Quick drying & No bleeding. Resistance to Acids, Alkalis & other chemical aggressions in finishing processes. Markings can withstand all textile sorting / sizing and finishing processes. Quick identification of lots upon fabrics dyed in dark shades also. Most economical method of marking on gray fabrics before processing. Available in 3 ball-point sizes for different types of fabrics Ink content: 60 ml (70g) Key provided to squeeze out the ink from the marker for optimum utilization & smooth flow. Direction of Use: Open cap. Insert the aluminum key provided with the marker at the bottom end of the tube & start rolling upwards for pressure. Mark on 90 degree angle for smooth ink flow. Keep rolling the key as pressure reduces. Do not fold the tube back & forth as it could lead to puncture. Do not use on other surface other than fabrics. Put the cap back on after use.
Century's High temperature marker is an industrial grade valve action paint marker for any surface. The ink is formulated specially for marking surfaces & objects that are exposed to very high temperature & harsh environments. It is made up of a hard aluminum body filled with ink and felt-tip with valve action for smooth ink flow. The markings have to be made at room temperature & works on all kinds of surfaces including steel, metals, ceramic, glass, rubber, concrete, alloys, wood etc. The markings made by the marker remain permanent at high temperatures up to 500-1093 degrees Celsius (930-2000 F) depending on the colour. The marker works on all porous & non-porous surfaces including metal, glass, ceramic, wood, plastic, rough, smooth etc. Ideal for Iron & steel, Automobile, Welding, Ceramic & Glass manufacturers. Tip Size: 2mm Advantages: Valve-action paint marker with hard aluminum body & a cap on top. Permanent & Heat-proof markings on all surfaces. Markings remain visible up to 500-2000 degree Celsius (930-2000 F) Works on all surfaces like steel, metals, alloys, plastics, glass, rubber, ceramics, concrete etc. Ideal for Iron & Steel Industry, Welding & Metal Cutting, Glass manufacturing, Ceramic Manufacturing, Automotive Industry, Power plants etc. Directions of Use: Open cap. Shake the marker well before first use. To push ink press the nib a few times until you see the ink on the tip. Put the cap back on after each use. Caution: Avoid contact from eyes or flames. Ink is harmful if consumed.
Century’s Hot Marking Chalk is a unique tool to mark onto red hot surfaces. It is widely used in industrial applications for coding & identification purposes. It makes very clear & bright markings on all kinds of metals, alloys, steel etc. and remains permanent up to 1400 degree Celsius (2500 F). The markings don’t fade, char, peel or drip away from the surface. They can work on any kind of surface rough, scraped; smooth etc. The advantage of the chalk over other markers or chalks is that the marker can be used when the surface temperature of the object is very high. These chalks are used for marking metals for laser cutting, instant and inflatable markings at varied temperatures, rough surfaces of steel castings, metal forgings, stainless steel sheets, metal plates, concrete slabs, Stripped & Rolled Items, Ingots Billets etc. Advantages: Ergonomic size makes it very easy to hold & write. Works on any kind of surface rough or smooth Markings do not fade, drip or chip off even at high temperature (up to 1400 degree Celsius) Markings can be made even when surface temperature is very high Ideal for Metal forging, Ingots, Billets, Hot Coils, Concrete slabs, stainless steel sheets, metal plates etc.
Share your thoughts with other customers for Century Inks Pvt. Ltd
Add Review
