Write a Review
Our Product / Services
Our product range contains a wide range of Female Threaded Adapters, Male-Female Threaded Adapters and Pushing Adapters
Female threaded adapters
Use these adapters on the ends of Push-Puller forcing screws, legs, or slide hammers in the removal and installation of shafts, axles, and housings.
Set No. 8044 consists of a set of 6 adapters (Nos. 8037-8042)
CAUTION:All the items shown may not withstand the full tonnage of the pullers they may be used with.
| Order No. | Female End "A" |
Female End "B" |
Order No. | Female End "A" |
Female End "B" |
|
|---|---|---|---|---|---|---|
| 8035* | 1/2-20 " | 5/8-18 " | 8040 | 5/8-18 " | 1-14 " | |
| 8036* | 1-14 " | 1-14 " | 8041 | 5/8-18 " | 1 1/8-12 " | |
| 8037 | 5/8-18 " | 5/8-18 " | 8042 | 5/8-18 " | 1 1/4-12 " | |
| 8038 | 5/8-18 " | 3/4-16 " | 8043* | 5/8-18 " | 1 1/2-12 " | |
| 8039 | 5/8-18 " | 7/8-14 " | ||||
Male-Female Threaded Adapters
These adapters are used on ends of Push-Puller legs, with forcing screws or slide hammers to assist in pulling shafts, bearing caps, pinions, and many other parts.
CAUTION:All the items shown may not withstand the full tonnage of the pullers they may be used with.
| Order No. | Female End | Male End | Length | Order No. | Female End | Male End | Length | |
|---|---|---|---|---|---|---|---|---|
| 8000 | 5/8"–18 | 1/4''–20 | 2 1/4" | 8015 | 5/8"–18 | 3/4"–10 | 2 1/4" | |
| 8001 | 5/8"–18 | 5/16"–18 | 2 1/4" | 8016 | 1"–14 | 3/4"–10 | 2 1/2" | |
| 8002 | 5/8"–18 | 7/16"–14 | 2 1/4" | 8017 | 5/8"–18 | 7/8"–14 | 2 1/4" | |
| 8003 | 5/8"–18 | 7/16"–20 | 2 1/4" | 8018 | 5/8"–18 | 7/8"–9 | 2 1/4" | |
| 8004 | 5/8"–18 | 3/8"–24 | 2 1/4" | 8019 | 5/8"–18 | 1"–14 | 2 1/4" | |
| 8005 | 5/8"–18 | 3/8"–16 | 2 1/4" | 8020 | 1"–8 | 5/8"–18 | 3" | |
| 8006 | 5/8"–18 | 1/2"–20 | 2 1/4" | 8021 | 1"–8 | 1"–14 | 3" | |
| 8007 | 5/8"–18 | 1/2"–13 | 2 1/4" | 8022 | 5/8"–18 | 1/8" pipe | 2 1/4" | |
| 8008 | 5/8"–18 | 9/16"–18 | 2 1/4" | 8023 | 1 1/4"–12 | 1"–14 | 4 1/2" | |
| 8009 | 5/8"–18 | 9/16"–12 | 2 1/4" | 8024 | 1 1/4"–12 | 1 3/4"–12 | 4 1/2" | |
| 8010 | 5/8"–18 | 5/8"–11 | 2 1/4" | 8025 | 1 1/4"–7 | 5/8"–18 | 4" | |
| 8011 | 1"–14 | 5/16"–11 | 2 1/2" | 8027 | 1 1/4"–7 | 1"–14 | 4" | |
| 8012 | 1"–14 | 5/8"–18 | 3 3/16" | 8028 | 1 5/8"–5 1/2 | 1"–8 | 4" | |
| 8013 | 5/8"–18 | 3/4"–16 | 2 1/4" | 8029 | 1 5/8"–5 1/2 | 1"–14 | 4" | |
| 8014 | 1"–14 | 3/4"-16 | 2 1/2" | |||||
| Note: Nos. 8000–8029 – each sold individually. | ||||||||
CAUTION:Pushing adapters (201923, 201454, 34510, 34511, 34755, 34756, and 44458) are designed for use with specific shaft sizes, and depending on the condition of the shaft ends, the adapter may not withstand the full press tonnage. Always use a protective blanket or other suitable guard when pressing.
| Order No. | Cap. Tons |
A (in.) |
B - Threaded (in.) |
C (in.) |
Weight (lbs.) |
|---|---|---|---|---|---|
| 28228†‡ | 10 | 2 3/8 | 1 - 8 | 1 1/2 | 0.8 |
| 28229†‡ | 25 | 2 7/8 | 1 1/4 - 7 | 1 3/4 | 1.0 |
| 28230‡ | 50 | 3 7/16 | 1 5/8 - 5 1/2 | 2 1/4 | 2.3 |
| 21332* | 80/100 | 3 7/16 | 2 1/4 - 12 | 3 | 4.0 |
† For CC10 or CC25 Hydraulic C-Clamps - Must be used with a threaded adapter (38597 or 38953).
‡ Used with Center Hole
* Used with Press Accessory Kits
| Order No. | Cap. Tons |
A (in.) |
B (in.) |
C (in.) |
D (in.) |
E -Threaded (in.) |
Weight (lbs.) |
|---|---|---|---|---|---|---|---|
| 201923†‡* | 10 | 3 1/8 | 2 1/4 | 5 3/8 | 1/2 | 1 - 8 | 1.0 |
| 201454†‡* | 10 | 3 1/16 | 2 5/8 | 5 11/16 | 3/4 | 1 - 8 | 1.4 |
| 34510†‡* | 25 | 3 1/4 | 2 5/8 | 5 7/8 | 3/4 | 1 1/4 - 7 | 1.7 |
| 34511†‡* | 25 | 3 1/4 | 2 5/8 | 5 7/8 | 1 | 1 1/4 - 7 | 1.7 |
| 34755‡* | 50 | 4 | 3 1/8 | 7 1/8 | 1 | 1 5/8 - 5 1/2 | 3.5 |
| 34756‡* | 50 | 4 | 3 1/8 | 7 1/8 | 1 1/4 | 1 5/8 - 5 1/2 | 3.5 |
| 44458* | 150/200 | 10 | 4 | 14 | 2 1/4 | 3 1/4 - 8 | 18.0 |
| Order No. | Cap. Tons |
A (in.) |
B - Threaded (in.) |
C (in.) |
D (in.) |
Weight (lbs.) |
|---|---|---|---|---|---|---|
| 34806†* | 10 | 2 5/8 | 1 - 8 | 1 1/2 | 1 | 1.0 |
| 34807†* | 25 | 3 1/8 | 1 1/4 - 7 | 1 3/4 | 1 1/4 | 1.5 |
| 34808* | 55 | 3 3/4 | 1 5/8 - 5 1/2 | 2 1/4 | 1 5/8 | 3.0 |
| 36469* | 80/100 | 4 | 2 1/4 - 12 | 3 | 2 1/4 | 4.8 |
| 44457* | 150/200 | 2 3/8 | - | 4 1/4 | 3 | 7.3 |
† For CC10 or CC25 Hydraulic C-Clamps - Must be used with a threaded adapter (38597 or 38953).
* Used with Press Accessory Kits
| Order No. | Cap. Tons |
A (in.) |
B (in.) |
C (in.) |
Weight (lbs.) |
|---|---|---|---|---|---|
| 309874† | 5 | 2 1/32 | 2 25/32 | 5/8 | 0.3 |
† May be used with CC5 Hydraulic C-Clamps (5 Ton).
Rounak Chindalia (Chindalia Industrial Products Limited)
C-23, Punit Industrial Premises Co-op Society Limited Plot 11a-11d, Midc, Ttc Area, Thane Belapur Road, Turbhe, Navi Mumbai - 400 705., Maharashtra - 400053
Share us via
