CHITRA Multi Mill is a self contained portable unit useful for high speed GRANULATING, PULVERISING, MIXING, SHREDDING AND CHOPPING, etc., of a wide range of wet and dry materials without special attachments. As compared to the four common principles of size reduction i.e. grinding, compression, impact and shearing, which often do not produce controlled size reduction, this machine utilises the principle of variable force swing hammer blades having both knife and impact edges rotating with a carefully selected screen to control size reduction. Flow path of material in vertical rotor machine is streamlined. During comminution, material entering the chamber travels to the periphery and passes through the screen tangentially and radially, avoiding chocking and temperature rise. OPERATIONMULTI MILL is designed to utilise the principle of variable force swing beaters having both knife and impact edges rotating within a selected screen to control the particle reduction. Material fed in to the processing chamber moves to the periphery and passes through the screen radially and tangentially. Finally the processed material gets collected in to the container kept below the processing chamber.SPECIAL FEATURESSuitable for dry and wet granules. All contact parts are made out of SS304 quality material.( SS316 quality is optional ) Castore wheel provided for the ease of mobility. Seaves available in sizes of 0.5 to 12mm hole dia. 12 nos. beaters with knife edges & impact edges & 02 nos. scrapper blades. In GMP Model complete body claded with SS304 and polished to the matt finish & in Standard Model excluding product contact parts, all other parts made out of C.I. or M.S. and coloured Machine rated for continuous operation. Higher output with process uniformity. All contact parts can easily be dismantled and cleaned for change of product. Wide range of SS perforated screens available Machine portable on castor wheels. , /li>Reversible direction of blade rotation. Different size of screen / speed / number of blade / direction of rotation of blade can be selected. TECHNICAL SPECIFICATIONSDrive motor : 3HP/ 1440 rpm / 3 Phase / 440V / AC D.O.L. starter provided with reversible switch. Rotor Diameter 89 mm ( approximate ) Rotor RPM : 50/1400 / 2200 / 2800 ( approximate ) Screen Diameter : 60 mm Blades 2 nos. With Knife & Impact Edges & 02 nos. Scraper Blades Out put 5 to 175 Kgs / Hr. Depending upon the products and the reduction required in sizes) Foundation not required. Castore wheel mounted base. Appro. charging/discharging height : 1445/730mm Appro. floor space required in mm : 870 X 965 Appro. net weight in Kgs. 275 Appro. gross weight in Kgs. 565 Case dimensions in mm 300 X 1080 X 1900 mm( ht ).OPTIONAL( Will be provided on extra cost on your demand ) Contact parts made out of SS316 instead of SS304. Providing flame proof drive motor along with flame proof push button station and flame proof reversible switch. Vacuum loading system fore charging the material. Stand for IPC. ( Intermediate product container )

OPERATIONIn recent times the most important development that took place is the replacement of the conventional reciprocating motion by the gyratory motion in the sieving and straining operation. This machine is designed to provide gyratory vibration generated by means of balance flywheel. The amplitude of vibration is adjustable to the processing needs by means of movable weight on the flywheel. This ensures that every point on the screen surface continuously transverses a circular path in horizontal plane with the elimination of the vertical motion.This is the only movement capable of effectively presenting in turn all the faces of irregularly shaped particles to the apertures of the screen. Again due to the absence of the vertical movement, bouncing of particles does not take place and thus presenting clear screen apartus. It is difficult to indicate specific data on the proper amplitude of gyration, for a specific product. However, it has been found that straining operation of liquid & solids calls for lower amplitude to avoid splashing unless the viscosity and tension of the liquid is high. SPECIAL FEATURESSimple design allows easy dismantling, cleaning & assembling. High speed machine with higher out put. It is compact & portable. , /li>Different size of sieves are available & it can be easily change to suit the product size required. Available in Standard & GMP Model. No dust problem due to close sieving operation. Castore wheel mounted structure, gives mobility of the machine. Very low maintenance cost. Wide range of sieves are available. Structure covered with SS304 cover, in GMP Model.OPTIONALFlameproof Motor with flameproof starter. IPC stand to put IPC at charging height. Conact parts made out of SS316 instead of SS304. TECHNICAL SPECIFICATIONSModel : 20" / 30" Drive Motor : 1.5 HP / 2.0 HP ( 1440rpm / 3Ph / 415 V / AC ) Screen Size : 550 mm / 750 mm All contact parts are made out of SS304 quality material. D.O.L. starter provided with the unit. Out put : Depending upon the material properties and the screen size.

INTRODUCTIONThe Liquid Manufacturing Plants are ideal tools for the pharmaceutical industry for the production of Oral Liquids. It is specially designed to take care of two critical factors which directly affects the quality of the Liquids. Minimum manual handling of Liquid. Effective cleanness during manufacturing. Needless to say, it also provides the benefits of the effective manpower utilization. "CHITRA" Liquid Manufacturing Plant consist the following equipments and accessories. Sr. No. Name of the Equipment01. Sugar Syrup Vessel 02. Manufacturing Vessel 03. Storage Vessel 04. Control Panel 05. Product Piping 06. Working Platform This system consist of a closed circuit manufacturing facility from feeding of Sugar / Water Phase to loading the Volumetric Liquid Filling Machine. The Sugar and Water, are load with vacuum system or by mechnical system or manually. The Sugar Syrup Vessel is supplied with high speed stirrer & electrical heating ( In small model ) / steam heating facility (In bigger size model ) .The sugar syrup is prepared at required temperature & are transferred to Manufacturing Vessel by vacuum or by transfer pump. The product during emulsion formation is recirculated through In-Line Homoginizer or Liquid Transfer Pump.( Optional Facility ) The Pump also discharges the product in the Storage Vessel. The Storage Vessel is then taken to the filling area ( if it is small capacity ) and is connected to again Liquid Transfer Pump. Or Storage Vessel remain fixed ( In bigger size) & pump transfer the Liquids in the float tank which is connected with filling machine. The entire Plant can be operated by centralised operating panel by one operator . The plant is equipped with an electrical control panel with digital temperature indicators / controllers and digital timers. Minimum two batches per shift of the same product can be assured in this plant. This plant conforms to CGMP standards (Paint Free Construction). Encosed are a few points explaining the system in detail. In case of any queries feel free to contact us. LIQUID MANUFACTURING PLANTThe Salient Features of the Liquid Manufacturing Plant are as follows : The Plant is designed to be operated only by one operator and one helper. All material transfers are done by vacuum or by transfer pumps. All the vessels are CGMP (paint free construction) The gaskets used are of silicon (food grade). All contact parts are of S.S. 304 quality material (SS316 provided on demand) & finished to class 4B (Mirror) finish and are crevice free. The entry of stirrer & high speed emulsifier are from top. In-line Emulsifier ( as per customer choice ) provided on demand. ( Optional ) All vessels are suitable for internal pressure of 1 Kg. / Sq. cm. and hence can be sterilized. All pipes, pipe fittings and valves are of SS304 / SS316 ( as per customer requirement ) seamless quality, internally electro polished, with tri-clover ended joints. The entire plant is equipped with CIP & SIP connections, so that customer can use these facility, if have CIP & SIP equipment. All values of temperature & time of the plant are indicated digitally on the control panel. Ampere indicates on Ampere meters. A micro processor based automatic operating plant can be designed as per requirement. (Optional ) All the inlet & outlet connections are provided with tri clover joints, which are very easy for cleaning & replacement.

CHITRA Multi Millis a self contained portable unit useful for high speed GRANULATING, PULVERISING, MIXING, SHREDDING AND CHOPPING, etc., of a wide range of wet and dry materials without special attachments. As compared to the four common principles of size reduction i.e. grinding, compression, impact and shearing, which often do not produce controlled size reduction, this machine utilises the principle of variable force swing hammer blades having both knife and impact edges rotating with a carefully selected screen to control size reduction. Flow path of material in vertical rotor machine is streamlined. During comminution, material entering the chamber travels to the periphery and passes through the screen tangentially and radially, avoiding chocking and temperature rise. OPERATIONMULTI MILL is designed to utilise the principle of variable force swing beaters having both knife and impact edges rotating within a selected screen to control the particle reduction. Material fed in to the processing chamber moves to the periphery and passes through the screen radially and tangentially. Finally the processed material gets collected in to the container kept below the processing chamber.SPECIAL FEATURESSuitable for dry and wet granules. All contact parts are made out of SS304 quality material.( SS316 quality is optional ) Castore wheel provided for the ease of mobility. Seaves available in sizes of 0.5 to 12mm hole dia. 12 nos. beaters with knife edges & impact edges & 02 nos. scrapper blades. In GMP Model complete body claded with SS304 and polished to the matt finish & in Standard Model excluding product contact parts, all other parts made out of C.I. or M.S. and coloured Machine rated for continuous operation. Higher output with process uniformity. All contact parts can easily be dismantled and cleaned for change of product. Wide range of SS perforated screens available Machine portable on castor wheels. Reversible direction of blade rotation. Different size of screen / speed / number of blade / direction of rotation of blade can be selected. TECHNICAL SPECIFICATIONSDrive motor : 3HP/ 1440 rpm / 3 Phase / 440V / AC D.O.L. starter provided with reversible switch. Rotor Diameter 89 mm ( approximate ) Rotor RPM : 50/1400 / 2200 / 2800 ( approximate ) Screen Diameter : 60 mm Blades 2 nos. With Knife & Impact Edges & 02 nos. Scraper Blades Out put 5 to 175 Kgs / Hr. Depending upon the products and the reduction required in sizes) Foundation not required. Castore wheel mounted base. Appro. charging/discharging height : 1445/730mm Appro. floor space required in mm : 870 X 965 Appro. net weight in Kgs. 275 Appro. gross weight in Kgs. 565 Case dimensions in mm 300 X 1080 X 1900 mm( ht ) OPTIONAL ( Will be provided on extra cost on your demand ) Contact parts made out of SS316 instead of SS304. Providing flame proof drive motor along with flame proof push button station and flame proof reversible switch. Vacuum loading system fore charging the material. Stand for IPC. ( Intermediate product container )