Centrifugal Pumps #633977

Self Priming Pumps Features :

• All wetted parts of pumps are made from lost wax process (investment casting), so surface finish is excellent. Smooth flow path/ hydraulic passage and no casting defects likeblow holes, cracks etc. are present.
• Centripetal / regenerative impeller for better suction.
• Pumps will be normally available in CF-8m /CF-8 (Gun metal,
• Alloy-20) and also in other material as per customer's requirements.
• Single /multistage pumps to handle crystal clear liquids for high pressure duties.
• Very quick priming & no need of foot valves.
• Very high suction capacity up to 8 meters without much noise
• Various types of sealing arrangements as per customer's liquid's characteristics.
• Normally fitted with carbon/ceramic seal faces with teflon cup and viton rubber.
• Pumps are available in monoblock and in bare type also with flameproof motor.
• All motors are of "TEFC" type
• Pump can be offered with electro polishing for some special requirements.
• Can handle temperature up to 80oC
• Trolley mount available.
• Also available with 120 Volt / 60 Hz.
• Custom built pumps are available, Mud pumps.

Applications :

All clear liquids without solid suspensions like diesel, petrol, LPG, oil, solvents, syrup, dm water, chemicals, steam boiler feeding, evacuation of condensate water, boosting of pressure, as a drum/barrel pump.

Features:

• Excellent, quick, automatic without foot valve up to 8 mtrs.
• Automatic air release during priming.
• Back pull out design, so easy maintenance can be done without disturbing pipe lines.
• Dynamically balanced rotating parts ensure lesser vibrations.
• Better efficiency because of good hydraulic design.
• Minimum parts & fast repairing at low cost, pump is also available at economical rate.
• Available in Bare, Coupled, Monoblock, Belt driven & Engine driven version.
• Also offered pump with trolley / trailer to move it from one place to another.
• Monoblock pumps can withstand with wide voltage fluctuations.
• Less expensive & easily available spares.
• Pumps can be fitted with mechanical seal as per customer's requirements.
• Very simple construction with only two moving parts.
• Easy inspection of impeller.
• Large diameter solids handled. (up to 60 mm)
• High resistance. to abrasive liquids. Wear plates are easily replaced and impellers are also available with ceramic coating
• Easy to install :only the suction hose is immersed in the liquid. The pump can be set up high and dry in the most convenient position for inspection and maintenance.
• Long Life :The parts subject to wear can be easily replaced one or more times to restore the original performance

Applications:

Public utilities :

• For pumping muddy water, sewage, polluted liquids, solid and in swimming pool.
• Dewatering Basements, Trenches, Construction sites.
• Onboard shift, as bilge, for desk wash & engine cooling
• Tiles & Marble factories, effluent plants.

Mobile Machinery :

• Cooling water for marine engines and shovels.
• Any application where priming is to be avoided.

Industry :

Transfer of clean or dirty neutral, acid or alkali liquids containing sand, mud or solids in suspension; clean or dirty low viscosity petroleum product or solvents; milk of lime, caustic soda; washing, cooling, circulation; smoke scrubbing; emergency duty.

Civil engineering :

Flood drainage; sewage pumping; fire fighting; recovery of dangerous liquids.

Naval duty :

Loading and unloading; bilge pumping; washing, fire fighting, stripping, sanitary duty and circulation.

Waste treatment:

pumping polluted, hot or corrosive waste water containing sand, mud or solids in suspension; dosing neutralizing liquids; pumping out settled sludge.

Construction industry :

Dewatering excavation, canals or ponds; ground water dewatering with well point system or drains; water supply from wells or canals; hosing down concrete castings.

Agriculture :

Surface irrigation; liquid manure oxygenation; transfer and spraying liquid manure or fertilizers, distribution of liquid animal feed; transfer of must; washing

Typical Application

• Liquid containing sand mud or solids in suspension with PH from
• 5-13, smoke scrubbing, water emulsion for machine tools or grinders, cutting or quenching fluid circulation, cooling water circulation in steel mills or drawing mills, neutralizing liquid dosage, pumping out settled sludge, sump pumping liquid manure transfer and circulation.
• Water circulation in paint spray booths, stripping fuel tanks circulation
• Recovery of dirty solvents
• Transfer of light petroleum product such as diesel fuel, paraffin, kerosene and petrol (gasoline)
• Liquid fertilizer transfer, circulation and spraying, brackish or sea water containing sand
• Brackish or sea water washing, cooling or fire fighting in ports, auxiliary duties on board
• Marine duty, brine, sea intake and circulation of sea water in swimming pools
• Pumping out acid waster, transfer, of dilute acids, fruit juice or fluid food products
• Recovery of spills from chemical plant, transfer or circulation of caustic or potash

Applications :

• Volute casing IN-LINE centrifugal pumps Type
• RIL are space saving pump units designed for easy installation and used generally for circulating clean non-aggressive fluids.
• Water supply Systems
• Water circulation /Transfer
• Hot water Circulation
• Agriculture
• Industry
• Ship Building
• Cooling Towers
• And many other Applications

Applications :

• Vertical multistage centrifugal pumps type MC are designed for a wide range of applications.
• Water supply systems.
• Water Circulation / Water Treatment Plant
• Hydro Pneumatic Systems / Condensate transfer.
• Agriculture / Industrial Washing
• Coolant Circulation.
• Boiler Feeding / Fire Fighting / Booster Applications.
• Ship Building / RO-DM Plants / Sprinkle irrigation

Features :

• Vertically split suction, intermediate and discharge casings clamped together by external tie bolt and sealed with gaskets
• Grease lubricated Antifriction Bearings designed to meet the requirements mounted on one or both side.
• Pump uses soft graphite lubricated asbestos. Special design of stuffing boxes with mechanical seals are available
• The suction and discharge nozzles are top vertical.
• The flanges are oval flange around flange as required by the design
• The round flanges when provided correspond to international standards
• The direction of rotation is clockwise as viewed from the driving end
• For suction more then 4 mlc the capacity reduces pump must be filled with liquid before they are started for the first time.

Applications :

• Irrigation - Sprinkler installations water works / fire fighting mining
• Fuel pumping Handling volatile liquid - wash down applications
• Hydraulic press / circuits Transfer & circulation hot & cold water
• Boiler feed pumps - Condensate pumps

Applications :

• Sewage and Effluent treatment plants.
• Low NPSH process circulation duty.
• Aboard ships as bilge, deck wash pump & engine cooling pump.
• Loading, Unloading and transfer of tricky liquids viz. oils, solvents, gas oils, minerals, oils, grease, petrol, seawater etc.

Applications :

• High Efficiency and High Discharge rate at less power Consumption.
• Casing and Impeller are made of SS 316
• Anticorrosive stainless steel shaft.
• Impeller is dynamically balanced for low noise and longer bearing life.
• Long life due to replaceable wearing parts.
• Easy spares availability
• Suction lift up to 8 meters.
• Extremely simple in construction, Easy Maintenance and Easy gland packing replacement.
• Available in various pipe sizes.
• Sealing arrangement with mechanical seal is standard supply, gland packing arrangement available on request.
• Mechanical seal with Carbon – Ceramic with S.S. Spring.
• Gland Packing (if fitted with) PTFE.
• SCFZ Series suitable for B5 TYPE IEC Motors.
• All models are available in 60 Hz on request

features :

• as all pumps are made from rolled stainless steel, mechanical properties are far superior than cast material.
• pore free, non-pitting and non-adhering smoother surface, so lesser friction losses, and lesser service corrosion.
• super finished surface also ensures no ingress or emission of germs or impurities during pumping or idling which is a basic requirement of sterile / hygienic application.
• pump can handle liquids having viscosities up to 1500 centipoises.
• pumps are highly energy efficient and requires lesser npsh to function without cavitation.
• the pumps can work under a vacuum of 720 mm of hg, suitable for vacuum evaporators.
• pumps are available with cosed/semi open impellers.
• the best elastomers are used in the pumps to provide optimum resistance for high temperatures and chemicals.
• minimum working / rotating parts.
• safe and quiet operation levels.
• gentle product handling with lower maintenance and downtime cost.
• dynamic combinations of seal faces as per customer's requirement (single seal / double seal, seal external cooling ).
• suitable for standard motor or flange type or foot cum flange type motor or engine
• monoblock or bare pumps or with trolley.
• also with flame proof motors.
• various types of connection like - tri'clove joints sms, flanges or threaded nipple/coupling.
• pumps with adjustable legs, available on request.
• special bearing for hot water application available on request

material of construction

• ss 304/ ss 316/ ss 304 l / ss 316 l
• seal silicon carbide or as per customer's requirement.

applications :

• milk, cream, butter milk, condensed milk
• fruit juice, beer, wine, sugar syrup
• vitamin solutions, sugar & confectionery.
• ro water, dm water, pure water. water for injection (wfi)
• vegetable oil, mineral oil, lub oil etc.
• pharmaceutical formulations, syrup etc.
• alkaline solution / alcoholic drinks.
• acids, fine chemicals
• bottling plants, soft drinks & distillery
• food processing / liquid food stuffs
• colour dyes and pigments / paints
• descaling applications, paper & cement industries
• water treatment plants
• detergent, soaps, paste & shampoo
• textile sizing, dyeing & finishing systems
• natural cellulose fiber / synthetic fiber system
• hot & cold water pumping

Features:

• Excellent quick automatic priming action without foot valve up to 8 mtrs.
• Automatic air release during priming.
• Back pull design, so easy to maintain without disturbing pipe lines. Dynamically balanced rotating parts ensures less vibrations.
• Better efficiency because of good hydraulic design.
• Non-clog impellers to handle solid particles up to 16 mm.
• Minimum parts, fast repairing at low cost, Also pump is available at an economical rate.
• Available in Bare, Coupled, Monoblock, Belt driven & Engine driven version.
• Also offered pump with trolley / trailer to move it from one place to another.
• Graded casting & perfect machining of all components ensure long life.
• ABLE TO OFFER PUMPS WITH CLOSED IMPELLERS FOR CLEAR LIQUIDS.
• Monoblock pumps can withstand wide voltage fluctuations.
• Less expensive & easily available spares.
• Pumps can be fitted with mechanical seal as per customer's requirement

MSEJ SERIES MUD PUMP

Features:

• This self priming (economical) mud pump, available from 0.5 hp to 5 hp in monoblock and bare version, with seal and without seal.
• Pumps are in std cast iron construction only(we can offer ss impeller if required).
• Compact design.

Applications:

Public utilities :

• For pumping muddy water, sewage, polluted liquids, solid and in swimming pool.
• Dewatering Basements, Trenches, Construction sites.

Onboard shift, as bilge, for desk wash & engine cooling.

Industrial :

• Petroleum product, Ceramic product Chemicals, Thermal plants etc.
• Tiles & Marble factories, effluent plants.

Marine Works :

Handling liquids from docs, ports and vessels etc.

Salvage Operations :

Fire fighting.

Mobile Machinery :

• Cooing water for marine engines & shovels.
• Any application where priming is to be avoided.

Applications:

• Creative engineers now introduces self priming cum centrifugal pump with closed and semi open impeller .
• We have made SS-304 or SS-316 chamber in round shape or in square shape .
• These chambers are interconnected with casings , casings have flap type or disc type non return valve (NRV) depend upon application . We use flap type NRV when liquid is dirty or containing some solid particles . We use disc type check valve when liquid is crystal clear.
• These NRVs hold liquid in the chamber and centrifugal pump works as self priming pump.
• All weted parts are made from SS-304 or SS-316 sheet only and chambers are tested with hydraulic test up to 10 bar . If more pressure is needed, than we test at 1.5 times the shutoff pressure. Thickness of sheet depends upon size and pressure of the system .
• These pumps are ideal for all applications where people do not want to use footvalve or have suction problem .
• Size of self priming chamber depend upon capacity and suction length .
• We also offer openable chamber so one can clean it very easily.
• This is required in sanitary application and in some sticky material application.
• All our CF series pumps are now available with such chamber in monoblock or bare version.
• All our mud pumps which is comparatively costly in SS castings are now offered in our new
• SPCF version with open or semi open impellers .