System Sensor Filtrex Smoke Detector provides early warning smoke detection in difficult environments where traditional smoke detectors are not practical. Filtrex provides protection in dirty, dusty environments that tend to cause false alarms with standard smoke detectors.
Operation:
Using a small air intake fan and a high density replaceable filter, air and smoke are drawn into a photoelectric sensing chamber while airborne particulate and water spray are removed. When the filter becomes too clogged to draw adequate air into the sensing chamber, power is cut from the detector, causing a trouble signal at the fire alarm control panel. When the filter is replaced, power-up is automatic.
Applications

• Animal research facilities
• Institutional laundry facilities
• Amusement parks
• Zoos
• Performance theatres
• Loading docks
• Paper mills
• Textile mills

Product Overview

• Intelligent communications
• High density filter removes particulate down to 32 microns
• Air delivery system is separately powered and fully supervised
• Filter is easily field replaceable
• Resistant to water spray in applications where occasional hose-down cleaning is performed
• Optional remote LED accessory
• Rotary decade address switches
• Compatible with 200 and 500 Series products’ protocol
• No modification required to panels compatible with System Sensor intelligent photoelectric smoke detectors

Specification
Size : 3.5" 8.9 cm) H x 6.1" (15.5 cm)diams in B5016-FTX base.
Weight : 7.3 oz (207 grams).
signaling Line Circuit Supply Range : 15-32 VDC
Detector Current (Max. Avg.) : 250 pA @ 24 VDC (without communication) & 360 pa @ 24 VDC (one communication every 5 seconds with LED enabled)
External / Auxillary Power Supply Voltage Range : 15.30 VDC (filtered)
External / Auxillary Power Supply Maximum Current : 123 mA
Temprature Rating : 32-122⁰F (0-50⁰C)
Relative Humidity : 10-93% Noncondensing
Air Intake Fan : On 5 seconds every 30 seconds
Filter : Air flow checked every 4 hours.

System Sensor Filtrex Smoke Detector provides early warning smoke detection in difficult environments where traditional smoke detectors are not practical. Filtrex provides protection in dirty, dusty environments that tend to cause false alarms with standard smoke detectors.
Operation:
Using a small air intake fan and a high density replaceable filter, air and smoke are drawn into a photoelectric sensing chamber while airborne particulate and water spray are removed. When the filter becomes too clogged to draw adequate air into the sensing chamber, power is cut from the detector, causing a trouble signal at the fire alarm control panel. When the filter is replaced, power-up is automatic.
Applications

• Animal research facilities
• Institutional laundry facilities
• Amusement parks
• Zoos
• Performance theatres
• Loading docks
• Paper mills
• Textile mills

Product Overview

• Intelligent communications
• High density filter removes particulate down to 32 microns
• Air delivery system is separately powered and fully supervised
• Filter is easily field replaceable
• Resistant to water spray in applications where occasional hose-down cleaning is performed
• Optional remote LED accessory
• Rotary decade address switches
• Compatible with 200 and 500 Series products’ protocol
• No modification required to panels compatible with System Sensor intelligent photoelectric smoke detectors

Specification
Size : 3.5" 8.9 cm) H x 6.1" (15.5 cm)diams in B5016-FTX base.
Weight : 7.3 oz (207 grams).
signaling Line Circuit Supply Range : 15-32 VDC
Detector Current (Max. Avg.) : 250 pA @ 24 VDC (without communication) & 360 pa @ 24 VDC (one communication every 5 seconds with LED enabled)
External / Auxillary Power Supply Voltage Range : 15.30 VDC (filtered)
External / Auxillary Power Supply Maximum Current : 123 mA
Temprature Rating : 32-122⁰F (0-50⁰C)
Relative Humidity : 10-93% Noncondensing
Air Intake Fan : On 5 seconds every 30 seconds
Filter : Air flow checked every 4 hours.