CRC Galva Brite Cold Galvanizing Spray forms a protective zinc-aluminium coating on the surfaces. It has corrosion protection properties. This spray is a combination of zinc and aluminium powders, resins and additives. A safety data sheet (MSDS) that is made as per EU directive 93/112 is available for all CRC products. When it comes to delivering spray, we use those shipment modes that enable us to deliver it on time.
Highlights :

• Excellent touch-up for galvanized surfaces
• Provides excellent corrosion and rust resistance to ferrous metals
• The galvanic properties ensure cathodic protection (the coating becomes the anode).
• Unique combination of flexibility and hardness
• Resists rusting, peeling and fading
• Adheres well to metal surfaces
• Combines the galvanized look with the convenience of an aerosol application
• Totally lead and chromate free
• No chlorinated and low-aromatic solvents
• Aerosols use dimethylether (DME) propellant for controlled spray and film properties

Applications :

• Fences and gates Home
• Garden and farm equipment
• Construction equipment
• Structural steel Guard rails
• Welding seams Pipes and fittings
• Coastal and ship borne installations
• Repair of LPG storage tanks

Directions :

• Shake aerosol can very well for at least one minute after agitator ball is free
• Stir or mix bulk product well to obtain a homogeneous dispersion
• Repeat frequently while using. Apply to a clean, degreased, dry surface for best results
• Remove rust and scale with a wire brush
• Apply in light, even coats; best results are obtained with 2 lighter rather than 1 heavy coat
• Additional coats can be applied after 15-20 minutes
• When spraying is finished, clean aerosol valve by turning can upside down and press button until only propellant escapes
• If clogging occurs, remove button and clean orifice with fine wire
• Do not use on energized equipment
• Use in well-ventilated area

Specifications :

• Appearance : bright aluminum finish
• Resin type : modified alkyd
• Pigment type : zinc, leafing aluminium
• Specific gravity : 1.06
• Flash point (solvents) aerosol : -4⁰C
• Coverage (30 um, dry) aerosol: approx. 1.6 m2/can (400 ml)
• Drying times to touch : 10-15 min
• Recommended film thickness : 30-40 um
• Thinner / cleaner : white spirit, acetates Dry film properties (35 um on degreased metal)
• Salt spray (ASTM B 117) : 100 h  (35 um film thickness)
• Adhesion on steel (NFT 30038) : 0
• Flexibility (6 mm mandrel, visual) : pass
• Heat resistance (4 h @ 200 °C) : slight
• Yellowing Hardness Persoz (after 72 h) : 80 s

CRC Galva Brite Cold Galvanizing Spray forms a protective zinc-aluminium coating on the surfaces. It has corrosion protection properties. This spray is a combination of zinc and aluminium powders, resins and additives. A safety data sheet (MSDS) that is made as per EU directive 93/112 is available for all CRC products. When it comes to delivering spray, we use those shipment modes that enable us to deliver it on time.
Highlights :

• Excellent touch-up for galvanized surfaces
• Provides excellent corrosion and rust resistance to ferrous metals
• The galvanic properties ensure cathodic protection (the coating becomes the anode).
• Unique combination of flexibility and hardness
• Resists rusting, peeling and fading
• Adheres well to metal surfaces
• Combines the galvanized look with the convenience of an aerosol application
• Totally lead and chromate free
• No chlorinated and low-aromatic solvents
• Aerosols use dimethylether (DME) propellant for controlled spray and film properties

Applications :

• Fences and gates Home
• Garden and farm equipment
• Construction equipment
• Structural steel Guard rails
• Welding seams Pipes and fittings
• Coastal and ship borne installations
• Repair of LPG storage tanks

Directions :

• Shake aerosol can very well for at least one minute after agitator ball is free
• Stir or mix bulk product well to obtain a homogeneous dispersion
• Repeat frequently while using. Apply to a clean, degreased, dry surface for best results
• Remove rust and scale with a wire brush
• Apply in light, even coats; best results are obtained with 2 lighter rather than 1 heavy coat
• Additional coats can be applied after 15-20 minutes
• When spraying is finished, clean aerosol valve by turning can upside down and press button until only propellant escapes
• If clogging occurs, remove button and clean orifice with fine wire
• Do not use on energized equipment
• Use in well-ventilated area

Specifications :

• Appearance : bright aluminum finish
• Resin type : modified alkyd
• Pigment type : zinc, leafing aluminium
• Specific gravity : 1.06
• Flash point (solvents) aerosol : -4⁰C
• Coverage (30 um, dry) aerosol: approx. 1.6 m2/can (400 ml)
• Drying times to touch : 10-15 min
• Recommended film thickness : 30-40 um
• Thinner / cleaner : white spirit, acetates Dry film properties (35 um on degreased metal)
• Salt spray (ASTM B 117) : 100 h  (35 um film thickness)
• Adhesion on steel (NFT 30038) : 0
• Flexibility (6 mm mandrel, visual) : pass
• Heat resistance (4 h @ 200 °C) : slight
• Yellowing Hardness Persoz (after 72 h) : 80 s