Light weight, stainless steel cradle carried, fitted with light Aluminum Alloy centrifugal pump having one 100 mm male round threaded suction inlet and Two 63 mm instantaneous female delivery outlets located at each side of pump. Highly reliable & extremely fast VANE PUMP type priming system (up to 8 meters within 30 seconds). Briggs & Stratton Vangaurd Gasoline engine 18 HP V-Twin overhead valve (OHV) type. The complete pump unit is suitable for effective fire fighting & for dewatering purpose.

• Performance - 600 lpm @ 6 bar & 800 lpm @ 5 bar


• Compliance - Full Compliance to PFPN 6-500 according to EN 14466


• Engine - Highly reliable Briggs & Stratton 2-cylinder 4-stroke Gasoline Engine


• Carrying Frame - Tubular steel carrying frame with easy four folding handles


• Priming System - Vane type priming system capable to lift water from 7 meters in less than 24 seconds and from 7.5 metres in less than 30 seconds


• Extremely Compact & Light in weight


• Flood lamp for night operations


• Available in Aluminium / Gunmetal / Stainless Steel Material


• Hassle free electric & Recoil type Rope Start for instant Start


• Economical - Fuel Tank capacity sufficient to run the Pump for 1.5 hours

Single stage centrifugal pump is directly coupled with a suitable engine and mounted on a trailer for surface transportation. The Pump is equipped with Exhaust priming system as standard for fast & effective priming from deep lift. However Firefly's reciprocating priming system "Primatic" which is completely automatic in operation can also be supplied with these pumps as optional. The engine is air cooled as well as water cooled for better performance. The complete set up is equipped with radiator, heat exchanger, battery, electric starter, 40 liters diesel tank, control panel etc. This unit can be used to combat fire for longer times.

Pump capacities can be made available up to 4000 LPM pumps with higher capacity engines.

ENGINE:

• The pump is driven by a close coupled suitable diesel engine.


• The engine is supplied complete with:


• Alternator


• Radiator


• Starter motor


• 12v battery


• Oil filter


• Fuel filter


• Oil cooler


• Cooling fan


• Exhaust silencer


• Air cleaner


• Heat Exchanger

he Performance data stated above is observed at test conditions (3.0 meters suction lift at NTP conditions)

For capacities other than stated above, please contact technical department.

Suction Inlet : - 100 mm

Priming: - Priming is provided by exhaust ejector priming.

Discharge Couplings: - 2 x 2.5 instantaneous screw down delivery outlets.

The shaft is supported by two sealed ball bearings. Shaft sealing is by the well known Firefly automatic mechanical seal incorporating a carbon seal running on a stainless steel counter face. The mechanical seal is pre-loaded and requires no maintenance or attention during its life.

PRIMER : -

As standard, pump is equipped with Exhaust primer capable of priming from 7 meters suction height within 7 seconds. However 'PRIMATIC' piston primer

(Capable of priming from 9 meter suction height) is also available as an option to exhaust.

The pump and engine combination is supported on anti-vibration mounts to cut down the noise and vibration. The complete unit is mounted on a heavy duty trailer for easy surface transport. Equipment can easily be maneuvered by two persons by help of two foldable handles. Equipment can be easily towed by any vehicle for surface transport. A tool box is provided for essential operational & maintenance tools. Suction hoses can be carried along with the trailer.

• The right of technical modifications & improvement without prior notice is reserved.


• The Performance data stated above is observed at test conditions (3.0 meters suction lift at NTP conditions).


• For capacities other than stated above, please contact technical department.

Firefly has developed second generation NXT-200 high pressure gun taking in to consideration the difficulties encountered in combating Indoor fire operations, incipient fires and forest fires. NXT-200 is advisedly designed so that fireman can rely completely on his equipments. The gun has proven its capability to achieve optimum extinguishing effects. It is extremely handy and user friendly.

We strongly recommended NXT-200 gun in combination with Firefly MP series fire pumps or any high pressure technology fire pump.

In practical terms NXT-200 consumes very little water during the operations and the micro-droplets evaporate completely and thus extract a maximum heat from the fire. Due to this; massive cooling effect are achieved. This cooling effect has two advantages; it cools the object on fire immediately and also saves the fireman from radiant heat from the fire, over & above it also saves the property being damaged due to heavy throw of water.

Adjustable jet to four operational conditions : -

i) Full Jet

ii) 30o narrow spray

iii) 60o wide spray

iv) 120o self protection water shield

All pump pressures like discharge pressure, vacuum etc. are digitally displayed.

Digital pump RPM meter.

Digital pump running hour meter, allows you to carry out scheduled maintenance work of pump & PTO at right intervals.

Pump oil temperature indicator with high temperature audio & video alarm.

Illuminated keys for Auto & Manual priming mode selection.

Auto prevention for use of primer above 2500 RPM.

Emergency bell key on panel.

Auxiliary display unit can be fitted in drivers cabin if required.

All current "Firefly" Fire Pumps of LP & MP Series, up to 2000 to 4000 L/min ranges of pumps can be fitted with a “Round–the-pump” Foam System (RTP) capable of inducing up to 120 liters per minute of foam compound into the pump. The system is compact and self-contained and is mounted on the pump suction tube and volute.

Material of Construction:

• For light alloy pumps: The pipe work and inductor are produced from aluminum alloy & the inductor itself is hard anodized.
• For Bronze Pumps: the body of inductor is available in bronze construction.
• Formula to calculate Foam meter knob reading :
• Foam meter knob reading = total discharge of pump × foam percentage to be injected.
• Eg. If; Total discharge of pump = 2000 LPM
• Foam percentage to be injected = 3%

Foam Intake size

We are Manufacturer, Exporter, Supplier of Power Take Off For Fire Tenders, Fire Hawk PTO and our setup is situated at Kolhapur, Maharashtra, India

• FM Series FireHawk" split shaft inline power take off are perfectly designed to transmit power & torque upto 300 HP vehicles.


• Installed in midship position between the truck transmission and & the rear axle.


• Throughput Torque Capacity - 10, 000 Nm


• Output Shaft Torque - 700 to 1000 Nm


• Weight - 92.5 kg


• Available Ratios


• Available in four different ratios (1:1.17, 1:1.31, 1:1.48, 1.1.62).


• Other ratios can also be made available on request.

• Gear case:- Made of high strength aluminum alloy making the PTO lighter (92.5 kgs approx) yet durable, which makes mounting/maintenance job much easier


• Gears: Helical gears; made from special alloy steel, carburized, are hardened and ground.


• Bearings: Oil lubricated oversized bearings make the P.T.O. stronger, silent in operation & operates at low temperature.


• Ratios: Available in four different ratios (1:1.17, 1:1.31, 1:1.48 & 1:1.62). Other ratios available on request.


• Torque: Designed to transfer


• Road shaft torque of 10, 000 Nm and Pump shaft torque of 700 to 1000 Nm.


• Cooling mechanism: Inbuilt water cooling system is provided for continuous operations. Sufficient fins are provided on PTO body for cooling while operating on road.


• Oil Seals: High quality double lip oil seals provided with dust guards offer virtually leak proof operations for extended periods, no frequent oil level check up is necessary.


• Gear Shifting mechanism:


• Automatic pneumatic self locking gear shift as standard.


• ( Air power allows the operator to shift from road or pump position by actuating a single button. Illuminated signal indicates completion of shift from road to pump.)


• Manual gear shift mechanism available as option is supplied with flexible control lever assembly.


• This makes fitment of control lever very flexible and easy in the drivers cab, especially with vehicles having tilting cabs.


• Front and rear bearing/bearing caps can be easily removed without removing the gear box from the vehicle; so reduced break down time


• Flanges to suit any requirements are available.


• Sufficient mounting pads are provided to suit mounting on any chassis.

• Compact LED illuminated water/foam tank level indicators


• Audio/ Video signal is given once water/foam tank level is below 25% of total volume which help to avoid dry running of the fire pump.


• Auxiliary display unit can be fitted in drivers cabin if required.

• Compact digital RPM meter for measuring pumps RPM


• Digital pump running hour meter, allows you to carry out scheduled maintenance work of pump & PTO at right intervals.