Other Products / Services #1453629

Cutter / Shredder / Chipper is operated threw cutting sharp bled .Two rollers uniformly feed long biomass stalk. Adjustable bled cutting material and blow outside. Distance between fix bed and bled is give output size result. It can be adjustable. System is operate threw 25 Hp electric motor or Mobile system can be work to joint at PTO shaft of tractor.

Application :

• Cutter / Shredder is for reduce bigger size for any kind of Biomass stalk and Wood pieces. It can works in farm with tractor operated PTO shaft or also utilized in factory with Electric motors.

System Specification :

• Feeding by - manual threw double roller
• Output Cutting Size - 10 mm or more
• Output capacity - 1 MT/Hr*
• Input Size Length - any
• Input size Diameter - Max. 25mm
• Moving Scope - By two wheels

Electricity / Power :

• Electric Motor - 25 Hp or 40 HP Tractor on site

Production Capacity :Continues feeding is must by manually. Output capacity is depends on the type of Raw Material. For Better production output and lower fuel consumption can be achieved if feeding is regular.

Silent Futures of Radhe Engineering Co. - Cutter / Shredder :

• Standard Heavy duty applicable MOC and design.
• For farm on site tractor operated and at factory optionally by electric motor.
• Mobility threw two wheels
• Feeding belt for essay input
• EN-31 bled for long life

In the Flash Dryer system, Input Biomass (with Higher Moisture) feed in a screw Conveyor mix with hot air. Hot Air which is generated from furnace passes with wet Biomass in duct line. Due to ID Blower developed negative pressure in full system up to duct line.
Moisture liberated from biomass due to more than 100.C Temperature inside system. Due to maximum Contact time and surface area moisture evaporate and separated threw blower discharge. At the bottom of Cyclone dry biomass collected and discharged threw RAV- rotary air lock valve. Moisture (Steam) and flue gases pass to ID fan to Bag house or Chimney.

Application :

• Flash Dryer is used for Drying Biomass like sawdust, Bamboo dust, sugarcane bagasse etc.

Output Capacity of Flash Dryer :

• Output Production Capacity - 1500 Kg/Hr. ( If input Moisture % Max. 30%)
• Input Moisture Percentage - 30%
• Output Moisture Percentage - 10%
• Water Evaporation Capacity - 400 Kg/Hr.

Output Capacity :

If moisture percentage is more then 30% Output prouction capacity will be propotionally less. Output drying capacity is depend on input material moisture %

System Specification :

• Type of Dryer - Flash Type
• Dry Threw - Hot air
• System Pressure - Negative/suction
• Fuel in Furness - Solid coal ( Briquettes/Fire Wood)

Technical Specification :

• Blower - 25 HP
• Rotary Air Lock Valve - 1 HP
• Screw Conveyor - 3 HP

Atomization for Operating :

• Feeding conveyor speed is operating as per cyclone outlet set point temperature.
• Servo control valve is operated as per desire temperature for system.

Land Area & Size ( Approx) :

• Length - 20 Feet
• Width - 15 Feet
• Height - 20 Feet

Silent Futures of Radhe Engineering Co. - Flash dryer :

• Maximum travel length with Hot air.
• Completely atomized feeding threw VFD drive as per operating parameters
• High capacity ID Blower
• Servo control valve to mix blend fresh air to desire input temperature from furnace
• Dust collecting system to as for control dust pollution.
• Temperature sensor at all required location to support atomization as a set point.

iomass briquetting Plant for converting agro forestry waste to Bio-coal / Briquettes . We are manufacturing Briquetting Plant / Hammer Mill / Dryer / Shredders etc. We have our own manufacturing facilities at our Gondal Plant We are offering fully technical support with friendly guidelines for set up new project Forest Green Energy Co. are ready to offer complete plant with erection and comissinning of project Forest Green Energy Co. will provide technical training facility to customers operator

Hammer Mill is utilized for convert uniform Sizing raw material / Bio-mass. Some agricultural stalk like cotton stalk. Sugarcane leaves, Soybean stalk, wood thin waste, veneer waste are available in big size, so it is not feed able for Briquetting machine.
It's require to cut below 10 mm to 15mm. Hammer mill is the best solution to sizing any kind of Biomass as per required size. Bottom screen can be change as per desired output size. Screw conveyor feed input raw material to Hammering chamber, where nos. of hammer rods are moving and hammering to biomass till convert in screening size Blower and Cyclone is for handling discharge output material.

Application :

• Biomass Hammer Mill is for converting long and uneven size of Biomass into uniform small size biomass raw material. After hammering raw material gives better result in Briquetting machine.

Production Capacity of Hammer Mill :

• Output Production Capacity - 1500 Kg/Hr.

Input Raw material ( Biomass) Specifications :

• Size of Raw Material- Length/Dia - Max. 100mm / 20mm)
• Moisture contain - Max. 8 %.

Output Raw material ( Biomass) Specification :

• Size - 10mm -15mm
• Form - Uniform Semi powdery / Powdery
• Output Production Capacity - 1500 Kg/Hr. *

Production Capacity :Output capacity is depends on the bulk density and type of Raw Material. So it will vary with different type and size of input raw material. If the raw material is bigger like stalk then Shredder / Cutter is required additionally. It will be 1000 Kg to 1500 Kg/Hr

Electricity / Power :

• Total Connected power Load - Approx. 41.5 HP
• Practical used Amp. Load - Approx. 35 - 50 Amp
• Power consumption - AApprox. 20 - 25 Unit/MT

Individual Electric data :

• Briquetting Main Ele.Motor - 30 HP
• Blower Motor - 7.5 HP
• Screw Conveyor Ele. Motor - 3 HP
• Rotary Air Lock - 1 HP

Silent Futures of Radhe Engineering Co. - Hammer Mill :

• Standard Heavy duty applicable MOC
• Due to atomization, whenever hammer mill main motor take more load feeding will stop and restart automatically.
• Separate big stone.
• Dust collector to prevent dust pollution after cyclone.
• Different capacity model available.

nce our establishment, we have become the famous manufacturer and supplier of a high quality Agro Waste Briquetting Machine. Designed to perfection following high definition engineering principles, this machine is widely utilized in several industries. Our provided machine is tested on various parameters in order to ensure its quality and durability. Clients can avail this machine from us in different technical specifications. Our clients can avail this plant from us at market leading prices. Features: Low power consumption Rigid design Long functional life

In Biomass Briquetting plant there are some continues wear and tear parts. Mainly it is a inner layer of die holed and pushing Ram. Due to high mechanical impact after some life it requires to be change. Life of these parts are depend on raw material used that mean silica type harder contain in raw material. If raw material is completely dust free it may long life. Simply life of these parts is depending on raw material quality.
Some auxiliary parts are also required to solution break down. Biomass Briquetting Parts is very imported as concern as quality and applicable alloy material and perfect size.

Wear & Tear Parts (Regular) :

• Ram (Hchc / En-31)
• Tapper Die (En-31)
• Split Die
• Collet

Wear & Tear Parts ( Long Time) :

• Ram Holder
• Feeder Box
• Screw Worm For Kupy
• Oil Seal - (Piston/crank)

Auxillary Spares :

• Die Holder
• Flange For Collet
• Flange For Feederbox
• Coupler For Kupy Worm
• Main Belt
• Filter - Inside/outside
• Oil Pump
• Oil Pressure Guage
• Pressure Valve
• Worm Blade For Conveyor