Post Buy Requirement
GP
Chennai, Tamil Nadu, India
Add Review

Other Products / Services

Butyl Rubber Sheets

Product Description

Butyl rubber is a copolymer or isobutylene and a small percentage of isoprene and has a very low permeability to air and other gases. It has excellent resistance to ozone, oxidation and sunlight, with an excellent temperature range of -45 C to + 130 C. Butyl has a very low resilience, which makes it ideal for vibration damping and shock absorption applications but offer a moderate resistance to abrasion and compression set. With careful compounding, Butyl compound can be made to acquire really good tensile strength. It is resistant to most inorganic products and highly resistant to mineral acids, alkaline and aqueous acids. We do not recommend its use in application where resistance to oils and Hydrocarbons is required. We can offer halogenated Butyl Rubber Sheets for specified applications

Code Specific
Gravity
Hardness
(±5)
Tensile
Strength
Elongation
at break
Compression Set
at 70°C for 22 hrs
Temp.
Range
Colour
gm / cm3 Shore A (min)
kg / cm2
(min)
%
% °C
CIIR 55110 1.10 55 130 550 25 -45 to +125 Black
IR 60120 1.20 60 90 350 40 -40 to +150 Black
IR 65135 1.35 65 60 250 40 -40 to +125 Black

 









View Complete Details

Ceramic Blankets

Product Description

Simwool Ceramic Fiber Blankets are manufactured in two temperature grades viz. 1260C & 1425C. It is made from Simwool Bulk Fibers, which is manufactured by using high purity Alumina, Silica and (Zircon). Double needling enhances the physical properties of the blanket, conferring good strength, handling ability, durability and resistance to delaminating.




Characteristics

  • Double needled blanket

  • Low thermal conductivity

  • Low weight comparatively other refractory material

  • Short heating & cooling time

  • Resistant to thermal shock

  • Flexible and easy to cut and install

  • Contains no organic binder

  • Asbestos free






Applications

  • Lining for furnace, kiln and oven

  • Expansion joint and seals for furnace, kiln and oven

  • Back-up insulation

  • Lagging of high temperature pipe work

  • High temperature filtration

  • Steam turbine and nuclear insulation

  • Pipe insulation

  • Fire protection








View Complete Details

Ceramic Boards

Product Description

Simvac Ceramic Fiber Board is made from refractory fibers and binders which have low organic content, the mixture is vacuum processed into boards that imparts good mechanical strength even after heating. Boards are manufactured in various densities and temperature grades to suit application requirements.




Characteristics

  • Low thermal conductivity

  • Resistant to thermal shock

  • Great Mechanical Strength

  • Even density and thickness

  • Able to withstand gas flow velocity of 30 m/sec

  • Easy to cut and install

  • Good erosion resistance

  • Short heat up and cool down time

  • Asbestos free






Applications

  • Hot face lining of ceramic fibre kiln

  • Insulation for kiln car

  • Furnace door insulation

  • Duct insulation

  • General thermal barrier

  • High temperature insulation



Grade (°C) Thickness

 

(mm)

STD. Width X Length

 

(mm)

Density (Kg/m3) Packing
1260 10 mm to 100 mm 500 x1000 320-384 12 pcs     (12mm)

 

 

06 pcs    (25mm)

 

04 pcs    (50mm)

 

02 pcs    (100mm)

1425 600 x 1000 320-384
 
View Complete Details

Ceramic Cloth

Product Description

Ceramic Clothes and Ropes are woven from yarn consisting of refractory ceramic fibre with approximately 20% organic carrier fibre. Inserted materials are incorporated into the yarn to increase fabric tensile strength. These products have exceptionally low smoke-off characteristics upon heating as compared with standard ceramic fibre textiles

View Complete Details

Ceramic Tapes

Product Description

Ceramic TapeRopes are woven from yarn consisting of refractory ceramic fibre with approximately 20% organic carrier fibre. Inserted materials are incorporated into the yarn to increase fabric tensile strength. These products have exceptionally low smoke-off characteristics upon heating as compared with standard ceramic fibre textiles

View Complete Details

Fevicol

Product Description

Features


Unsurpassed bonding strength
Resistant to water & heat


Areas of Application


Plywood to Laminate
Plywood to Veneer
Any Wood to Wood bonding
MDF/Particle board/Block board to laminate


50 G, 125 G, 250 G, 500 G, 1kg, 2kg, 5kg, 10kg, 15kg, 20kg, 30kg, 50kg, 200kg

View Complete Details

M Seal

Product Description

Features


Sets in 30 minutes (at 27C)
Can be moulded into different shapes
Cures to a hard mass
Provides rock hard sealing. Can be shaped, drilled, filed, sanded, painted upon


15g, 30g, 50g, 75g, 100g, 250g, 1kg

View Complete Details

Rustolene

  • Appearance Clear liquid
  • Colour Reddish
  • Specific Gravity 0.84 -/+ 0.02 (at 30°C)
  • Flash Point 45°C(min)
  • Coverage 90m2/ltr
Product Description

Rustolene is a powerful rust dis-integrating solution. It is a quality product that has been a trusted for Rust removing for years. This is a multipurpose maintenance aid and significantly reduces the maintenance cost. It is specially formulated to fight rust, which makes it indispensable to industrial plant, factories and garages.


Overall Rustolene acts as a dis-integrator, dismantler, Lubricator, decarboniser & cleaner The active ingredients in Rustolene attack the point where rust and metal parts are bound together and consequently eliminate rust from the surface. It also penetrates the tightest of joints reaches between the finest of threads and enters the innermost points of inaccessible mechanisms


USAGE:



  • Used in industries for rust disintegration and lubrication for pipelines.
    *Opening of jammed nuts & bolts
    * Pipeline
    * Crushing & Grinding Equipments
    * Valves & Pumpset.
    * Motor Power Generators
    * Lifts, Crane, Hoists, Sprocket.
    * Storage Tank
    * Compressors 7 Blower
    * Heat exchangers.

  • Office Equipments
    * Type writer
    * Duplicator Machine
    * General Machines

  • Farm MAchines
    * Thressing Machine
    * Combine harvesters
    * Tractors

  • Automobile
    * Garages for cleaning of all metallic parts & Engine.

View Complete Details

Aluminum Putty

Product Description

Aluminum-filled epoxy putty for dependable non-rusting repairs to aluminum castings, machinery and equipment widely used in HVAC applications.


KEY FEATURES


  • Repairs air conditioning system components

  • Listed under NSN Stock #8030-00-051-4511; #8030-00-670-8553

  • Bonds to aluminum and many other metals

    • Fills porosity in aluminum castings



  • Can be machined drilled or tapped using conventional metalworking tools

  • Qualifies under Mil Spec MIL-PRF-24176C, Type II

View Complete Details

Bronze Putty

Product Description

Bronze-filled epoxy putty for repairing bronze and brass bushings, shafts, castings and equipment parts.


KEY FEATURES


  • Repairs and rebuilds areas where brazing would be undesirable or impossible

  • Bonds securely to bronze alloys, brass, copper, and ferrous metals

  • Uses conventional metalworking tools to machine, drill, tap, or grind

  • Listed under NSN stock #8030-00-333-4534

View Complete Details

Stainless Steel Putty

Product Description

Stainless steel-filled epoxy putty for patching, repairing and rebuilding stainless steel food processing equipment


KEY FEATURES


  • Non-rusting

  • Bonds to ferrous and non-ferrous metals

  • NSF certified for potable water applications

  • Acceptable for use in meat and poultry plants

  • Listed under NSN stock #8030-00-268-7934

View Complete Details

Titanium Putty

Product Description

High-performance, non-rusting titanium-reinforced epoxy engineered for making repairs to machinery and equipment that can be precision machined. Withstands heavy loads in hard chemical envirnoments.


KEY FEATURES


  • Excellent temperature resistance (350F)

  • High compressive strength (15, 200 psi)

  • Resistance to chemicals and most acids, bases, solvents, and alkalis

  • Qualifies under Mil Spec MIL-PRF-24176C, Type I

  • Listed under NSN stock #8030-01-335-0562

View Complete Details

Ptfe Round Bar

  • Thickness 2-6 mm
  • Sizes nominal bore 20-150 mm

Our gamut of precision industrial products comprises of PTFE Round Bar which include glass filled, carbon filled, bronze filled, liner PTFE, bar, etc. These bar are extensively used in various industrial applications owing to their unique qualitative features such as:

View Complete Details

Aramid Packing

  • Temperature -200°C to 300°C
  • Pressure upto 280 Bar
  • PH 3 -12
Product Description

Features:


ANTI ABRASIVE PACKING Duplex Plaited Non-Asbestos Synthetic Fibre product which is as strong as steel, as smooth as silk, most flexible and treated with high temperature resisting lubricants, under controlled conditions. Well suited for pumping granular and viscous fluids even under high pressure conditions.


This packing has a high degree of resiliency and consistency of volume and hence avoids frequent gland adjustments. Low thermal expansion characteristics under actual operating conditions reduce mechanical pressure against shaft sleeves to minimise abrasion effect.



1. Sizes 3 mm to 5 mm is supplied in spools of 10 mtrs.


2. Size above 5 mm is supplied in Boxes/Kgs.


3. Also can be supplied in accurate cut rings.



Recommended

View Complete Details

PTFE Packing

  • 1) Max. working temperature -75°C ~ 260°C
  • 2) Max. working pressure 2Mpa (rotary pump)
  • Max. working pressure 10Mpa (reciprocating pump)
  • Max. working pressure 15Mpa (valve)
  • 3) PH value 02/12/18
  • 4) Linear speed 0 – 10m/s (rotary pump)
  • Linear speed 0 – 2m/s (reciprocating pump)
  • Linear speed 0 – 2m/s (valve)
  • 5) Cross Section 1/8″ ~ 3″(3X3-75X75mpa)
  • 6) Density 1.35 ~ 1.45g/cc
Product Description

Asbestos PTFE packing is made of white asbestos fiber cords impregnated with PTFE dispersion. Soft in texture, this material is suitable for sealing pumps for various chemicals. However, packing impregnated with lubricants is recommended for use with reciprocating pumps or for sealing in places where high linear velocity.


Application conditions:

View Complete Details

Carbon Fiber Packing

  • 1) Max. working temperature -200°C ~ +650°C (STEAM) -200°C ~ +565°C (ATMOSPHERE)
  • 2)Max. working pressure 5 Mpa(rotary pump)
  • Max. working pressure 15Mpa(reciprocating pump)
  • Max. working pressure 25Mpa(valve)
  • 3)PH value 0-14
  • 4)Linear speed 0-20M/S(rotary pump)
  • Linear speed 0-2M/S(reciprocating pump)
  • Linear speed 0-2M/S(valve)
  • 5) Cross Section 1/8″ ~ 3″(3X3-75X75mm)
  • 6) Density 1.35 ~ 1.45g/cc
  • Regular package 5 or 10kg/roll
Product Description

Features:


Carbon fiber packing with graphite is woven of strong carbon fiber after softening treatment and impregnation with a mixture latex of fine graphite powder, PTFE dispersion and lubricant. It is chemical resistant, heat conductive and with high strength, so this item is widely used with revolving and reciprocating pumps in which chemical corrosive media and particle grains exist. The successful test result in application of high pressure ammonium and luiquid ammonia pumps proved its the best sealing material for high pressure a, high temperature and corrosion.


Application conditions:

View Complete Details

Composite Aramid Fiber Packing

  • 1) Working temperature -100°C – +260°C
  • 2) Max. working pressure 5Mpa(rotary pump)
  • Max. working pressure 10Mpa(reciprocating pump)
  • Max. working pressure 20Mpa(valve)
  • 3)PH value 02/12/18
  • 4) Linear speed 15M/S(rotary pump)
  • Linear speed 2M/S(reciprocating pump)
  • Linear speed 2M/S(valve)
  • 5) Cross Section 1/8″ ~ 3″(3X3-75X75mm)
  • 6) Density 1.50 ~ 1.65g/cc
Product Description

Composite aramid fiber packing is made from imported aramid short fiber which is twisted in advanced technology and impregnate with PTFE latex and high-temperature lubricated, its softer than common aramid fiber packing and has more content of PTFE and lubricant to make sure its fibers closer to each other to supply high lubricant and low abrasion of shaft, especially suitable for reciprocating pumps with small grains, high pressure and high line speed.
Application conditions:

View Complete Details

Expanded Graphite Packing

  • 3) PH value 0 – 14
  • 4) Cross Section 1/8″ ~ 3″(3X3-75X75mm)
  • 5) Density 1.10 ~ 1.35g/cc(with cotton, fiberglass, ss304, inconel)
  • Density 1.50 ~ 1.60g/cc(with inconel jacketed)
Product Description

Expanded graphite packing is braided from high-grade low sulphur expanded graphite yarn. This item has superior resistance from high temperature and chemical corrosion, as well as other special sealing effects.Its widely used in steam valves of powder station, , static sealing with high temperature, high pressure and chemical corrosion.
Application conditions:
1) Max. working temperature:- 200C +650C (STEAM)
-200 +565 (ATMOSPHERE)
2) Max. working pressure: 25 Mpa
(can only be used in valve and other static sealing condition)
(1)Expanded graphite packing(with carbon fiber, SS wire, inconel wire)pressure:35 Mpa
(2)Expanded graphite packing(with inconel jacketed)pressure:40 Mpa

View Complete Details

GFO Packings

  • 1)Working temperature – 200°C ~ +280°C
  • 2) Max. working pressure 3 Mpa(rotary pump)
  • Max. working pressure 10Mpa(reciprocating pump)
  • Max. working pressure 20Mpa(valve)
  • 3)PH value 0-14
  • 4)Linear speed 22M/S(rotary pump)
  • Linear speed 2M/S(reciprocating pump)
  • Linear speed 2M/S(valve)
  • 5) Cross Section 1/8″ ~ 3″(3X3-75X75mm)
  • 6) Density 1.40 ~ 1.50g/cc

Features:


Gore fiber produced in USA is superior in heat-condution, lubrication, and corrosion resistance.it can emanate attrition heat in high speed. Even the shaft speed is up to 21m/s , the packing wont turn to be hot , hard or broken.Its suitable for application of various pumps and valves.


Application conditions:

View Complete Details

Graphite Packing

  • 1) Working temperature – 200°C ~ 650°C (STEAM) -200 ~ 565 (ATMOSPHERE)
  • 2)Max. working pressure 35Mpa
  •    
  • 3)PH value 0-14
  • 4)Linear speed 0-2M/S(valve)
  • 5) Cross Section 1/4″ ~ 1-1/2″(6X6-38X38mm)
  • 6) Density 1.10 ~ 1.20g/cc
Product Description

Features:


Graphite gland packing with carbon fiber corner is braided from expanded graphite yarn, which can withstand high temperature and carbon fiber with superior corrosion resistance. The carbon fiber in four corners provides higher resistance to extrusion and attrition. This packing can effectively avoid leakage, especially suitable in application of power stationvalve with high temperature and pressure.


Application conditions:

View Complete Details

PTFE Bellows

Product Description

PTFE Bellows for Lined Pipes


Bellows are specially designed form virgin PTFE and is contour moulded. This manufacturing method guarantess an excellent structure of the material; Symptoms of ageing are practically excluded. Very long term durability and low maintenance costs are assured.


These Bellows are manufactured in different sizes form NB 25mm to NB 500mm. The allowable operating pressures are depending on services conditions. The Bellows can be used upto 200C.


Bellows serve for compensation of:



  • Vibration

  • Thermal Strain and Expansion

  • Axial and Redial motion


These Bellows are meant for resisting highly corrosive chemicals plants and piping for aggressive medias.
These Bellows are installed in PTFE Lined Carbon Steel Piping and equipment without additional gaskets. For use with piping and equipment made of glass, enamels and ceramics we recommend PTFE Gaskets, offered as accessory.


The sealing surfaces are covered end plates and individually boxed for protection against mechanical damage. Limit bolts are preset to prevent over extension during operation.

View Complete Details

PTFE Molded Sheet

Standard Size :



  • Thickness From 1.5 mm to 100 mm / 300 mm2/ 400 mm2/ 450 mm2/ 500 mm2/ 600 mm2/ 900 mm2/ 1000 mm2/ 1200 mm2


Available Grades :



  • Virgin PTFE

  • 15 % Peek PTFE

  • 15 To 25 % Glass Filled PTFE

  • 25 To 35 % Carbon Filled PTFE

  • 15 % Graphite Filled PTFE

  • 40 to 60 % Bronzed Filled PTFE

  • 5 to 15 % Aluminum Oxide Filled PTFE

  • 5 to 10 % Stainless Steel Filled PTFE

  • 5 to 10 % Mica Filled PTFE

  • 55 % + 5 % Bronzed + Molybdnum Disulphide Filled PTFE

  • 15 % + 5 % Glass + MOS2 Filled PTFE

  • Pigmented PTFE

View Complete Details

PTFE Rods Bushes

  • Length 300 – 900 mm (standard)
  • Length 3000 – 12000 mm
  • Length 100 mm (standard) upto 300 mm in special cases.
  • Length upto 5000 mm
  • Dia 3 – 250 (standard) large sizes made to order
  • I.D. 1.6 – 25 mm
  • Wall Thickness 0.8 – 1.6 mm
  • O.D. 32 – 150 mm (standard)
  • I.D. 12.5 – 127mm (standard)
  • O.D. 25 -100 mm
  • I.D. 19 – 89 mm
  • Wall Thickness 3 – 25 mm
View Complete Details

PTFE Sheets

  •   Sizes available
  • 300 x 300 mm to 900 x 900 mm Thickness
  • 3 – 25 mm Thicker sheets available on request Width
  • 300 – 600 mm Thickness
View Complete Details

Ptfe Tube

Product Description

We deal inPTFE Tubeand PTFE Pipe in wide range of standard size products and also customized lengths and sizes as per your requirement. PTFE Tubes are known for its characteristic use in high temperatures, chemical resistance and lubricity.

View Complete Details

PTFE Bellows Line

  • Line Bellows Nominal bore 25 – 225mm. Bigger sizes on order.
  • Valve Bellows Complete with spindles. Nominal bore 25 mm onwards.
  • Stirrer Bellows Nominal bore 25 mm onwards. These bellows can be supplied with / without steel flanges.
Product Description

Type:



  • Line; for Flanges

  • Valve; with Spindle

  • Stirrer


Used mainly in chemical process pipelines and chemical manufacturing equipment.

View Complete Details

PTFE Flex-O Seal

Product Description

Introduction:
Flex-O-Seal is a unique sealing material manufactured from special grade of expanded 100% pure PTFE by transforming the fibrous structure by means of a special process. Though very tough, it is spongy and suited to almost all flanges, covers and narrow cavities. Its special soft and flexible character enables it to be the most ideal seal under pressure without significant cold flow even on irregular, badly damaged or corroded flange surfaces. Once bolted this gasket rarely need to be retorqued.


Properties:FLEX-O-SEAL recommended temperature-240C, to 310C, PH Range 0-14 No deterioration due to stocking for long time. Resistant to high pressure, non-toxic.
Not recommended for use against elemental fluorine, alkali metals and strong oxidising agents.


Application:
FLEX-O-SEAL is safely used in petroleum refinering companies even in their offshore operations, corrosive chemical processing, food processing, paper mill, marine installation, for glass lined or fibre glass reinforced vessels and tank lid sealing, manhole covers, vent pipes, heat exchangers, pumps or compressors housing flanges, valves and many more industrial applications where conventional pre-cut gaskets are not readily available or unsuitable.


Installations:



  • The sealing surface must be clean, free from grease and dry to enable the gasket to stick properly.

  • The width of the joint gasket is to be determined by the nominal diameter or type of flange. Selection of a tentative size of joint gasket would be approx, 1/3rd flange contact width inside the bolt hole e.g., 7 mm gasket joint to suit a 20 mm flange width.

  • Remove the protective foil from the adhesive joint gasket to allow for fitting. Stick the gasket approx 2 mm away from the bolt hole and press on lightly.

  • Do not butt the ends overlap them in front of a bolt (see fig. 1)

  • Tighten the lubricated bolts in opposite pairs. Since it is highly compressible only bolt pressure is required to seal. The lap joint deforms perfectly to give a reliable seal.

  • For delicate components such as glass flanges the gasket ends can be joined by cutting a step in each end of gasket.

  • FLEX-O-SEAL is easy to install, able to fill severe surface irregularities and reduces inventory of ready made gaskets, envelopes, etc. It has therefore taken its name as UNIVERSAL JOINT GASKET.

  • On irregular or damaged flanged surfaces, it is possible to build up with short length of FLEX-O-SEAL.

Gasket Widthmm Thickness mm Spool length meter
3 1.5 30
5 2.0 20
7 2.5 15
10 3.0 8
14 5.0 5
17 6.0 5
20 7.0 5
25 10.0 5
View Complete Details

Carbon Filled PTFE Tube

Product Description

We specialize in manufacturing and supplying a qualitative assortment ofCarbon FilledPTFE Tube. Our tubes are made using optimum quality components and widely acclaimed for their various salient features including wide temperature range, non-toxic and non-flammable nature, chemical resistance, non sticky nature, extremely high dielectric strength and lowest co-efficient of friction. These are ideal to be used at the places where insulation may be damaged by hot soldering irons.

View Complete Details

Steel Grip

Product Description

Steelgrip Electrical Tapes have been developed from carefully selected backings and adhesive systems. The adhesive used in the manufacture of the tape have been developed with a special formulation to withstand different classes of temperature from Class A-105C to Class H-180C and includes Rubber, Acrylic and Silicon based formulations.
Detailed Product Description Applications



  • Electrical cables insulating

  • Cable wrapping and bundling

  • Color coding, directional marking, marking out rehearsal areas

  • Cable reinforcing and protecting

  • Electrical repair


Features



  • Fire-resistant.

  • Non toxic (in room atmosphere conditions)


Color:


Red, Blue, Yellow, Green, Black

View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Gasket Prodcuts (Gasket Prodcuts)
  • No. 113B,Angappa Naicken Street, George Town, Chennai, Tamil Nadu - 600001, India
  • Share us via
  • Call 08069182201 Ext. 344