The device works with both ultrasonic contact impedance (UCI) and dynamic (Leeb) probes. User get the benefits of two methods of measurement it is the maximum that can be obtained from a portable hardness tester.

Dynamic (Leeb) probe is used for measuring the hardness of non-ferrous metals, cast iron, coarse-grained materials, massive products etc.

The ultrasonic contact impedance (UCI) probe is used for measuring the hardness of small items, objects with a thin wall, complex form, and to measure the hardness of surface hardened layers.

Standard set of Hardness Tester-

Electronic unit, UCI probe, Leeb probe, 2 batteries AA, Charger, USB cable, Operating manual, Software for PC, Case.

Available options for ordering of Hardness Tester

UCI probe, Leeb probe, Batteries, Charger, USB-cable, Set of measures of hardness, Case

UCI Hardness Tester is designed for rapid non-destructive testing of hardness.Metals and alloys on standardized international scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV);

The ultrasonic contact impedance (UCI) probe is used for measuring the hardness of small items, objects with a thin wall, complex form, and to measure the hardness of surface hardened layers.

Measurement hardness range:

• Rockwell, HRC - 20 - 70


• Brinell, HB - 90 - 450


• Vickers, HV - 230 - 940

Standard set of UCI Hardness Tester

• Electronic block


• UCI probe


• 2 batteries AA


• Charger


• USB cables


• Operating manual


• Software for PC


• Case

Measuring the hardness of the surface hardened layer Possibility to use in field conditions with high humidity and dust Convenience and ease of measurement Optimized number of buttons Contrast display with bright back-lighting Automatic recognition of probe Indication of the type of connected probe Calibrations stored in memory of probe Very easy in operation and calibration Internal memory and communication with PC Rubber bumper protected case

Micro Vickers Hardness Tester designed to cater heavy duty and research work with all the necessary automation for loading and measurements.

Test Load- 10gf to 1000 gf (0.098, 0.246, 0.49, 0.98, 1.96, 2.94, 4.9, 9.80 N) 10, 25, 50, 100, 200, 300, 500, 1000 gmf dial switchable.

Dwell time - 5 - 60 Seconds.

Loading Mechanism Motorized loading and releasing.

Indexing- Rotating turret for indenter and objective lens.

Objective For scanning 10 x, Plan achromatic 0.25 NA.

For measurement 40 x, Plan achromatic 0.4 NA.

Diagonal Reading - Manual Filler micrometer eyepiece (10 X) with 0.5 Micron accuracy OR Digital measurement with the help of Digital Filler micrometer eyepiece (10 X) with 0.025 Micron accuracy.

Computerised Attachment:With this attachment one can convert manual hardness to computerized one. This has many advantages like higher accuracy as of bigger indentation, operator ease as one can get the Microhardness value by just clicking two diagonals of indentation image on the screens. Further one can get plot of effective case depth graph. All the readings with image and graphs can be stored, printed. This model MVH-II consists of

• 1/2" CCD Camera (High resolution monochrome) with interface adaptor


• Image grabber hardware.


• Dedicated image processing Software for Vickers Hardness number, effective case depth hardness graph. Hardness Conversion facility.

Rockwell, Rockwell cum Brinell, Rockwell cum Rockwell Superficial

Hardness Testers are designed and developed after years of experience in this field. All the models are manufactured under strict quality control at all manufacturing stages.

These models are suitable for testing hardness of metals and alloys of all kinds, hard or soft, whether flat or round etc. or of irregular shape. These testers are simple in design and easy to operate, still yet quite sensitive and accurate.

These models strictly conforms to IS: 1586-2000, BS: 891 part 1 & 2 for Rockwell & Rockwell superficial test. IS: 2281-1983, ASTM-E-10 for brinell test.

Automatic weight selection with automatic zero setting dial gauge.
Automatic weight selection with automatic zero setting dial gauge with more testing height and throat

Automatic weight selection with automatic zero setting dial gauge.
Arrangement similar to RS with two additional weights of 185.5 kgf and 250 kgf for brinell tests.
On this machinesmall pin having Dia 2 mm can be tested as plunger is guided with a set of six bearings.

This hardness tester is similar above machine in construction, and with automatic weight selection. This is useful for carrying Rockwell and Rockwell Superficial tests. The Rockwell Superficial method is useful for checking hardness of very thin sheets and surface hardness.

Application and removal of major load is motorized. Motorized models have semi automatic operations for products testing. Drive motor-single phase, 230-V, 50 cycles AC.

Mainly used to check hardness in confined spaces, on large & heavy components, permanently installed parts with low test expenditure. The machine has built in conversion facility for given material to convert D value to Vickers (HV), Rockwell (HRB, HRC), Brinell (HB), UTS scales which can be selected by pressing arrow keys. 30 hardness scales for different probes selectable by feather touch keys. Alpha numeric display 16 characters x 2 lines user friendly software. Display indicates selected material & scale combination & hrdness value. Facility to connect dot matrix printer Upto 100 readings can be stored.

This instrument measures the rate of extrusion of Molten resins through a die of specified length and diameter under prescribed conditions of temperature, load, piston position.

Instrument with following accessories will be supplied Digital stop watch, Temp. Controller ( PID ), Piston, Orifice remove, Barrel Cleaner,

Brinell hardness tester, are designed for Brinell hardness measurement on steels and other ferrous materials and also on non ferrous materials like Brass, Bronze, Aluminum, etc. the material can be cast, forged or rolled and the shape can be flat, round irregular.

The actual load application system is of dead weight type combined with mechanical lever system. The supporting hydraulic system is for initial of load before each test and damping the load application system for smooth application of load.

A separate hydraulic power pack, positioned in the bottom part of the machine increase the machine stability.

Design of a floating fulcrum lever system ensures high accuracy and dependability.

The machine accuracies confirm to IS: 2281-2005 & BS: 240

AUTOMATIC OPTICAL BRINELL HARDNESS TESTERS

• The machine has a robust, C-type load frame & has been designed for production testing of cast or forged components like leaf springs, cam shafts, etc. for Brinell hardness value. This machine is suitable for foundries, engineering industry on production line.


• Since most of the operations are fast and automatic, the test speed is high with less operator fatigue.


• The cycle time (except loading / unloading) is about 12 seconds per test.


• Load stages 750 kgf and 3000 kgf.


• Optical measuring equipment with 14 X magnification.


• Job loading / unloading, push button operation, pushing cycle start, de-clamp buttons are only manual operations & rest all is automatic.


• A push button is pressed for cycle start & hydraulic operations. After cycle time, impression is visible on screen, which (Diameter) is to be measured with the help of microscope of least count 0.01mm.


• Computerized model is available .Computerized model has built in CCD and suitable advanced software. Hardness will be displayed On computer monitor automatically. Results printout can be taken.


• Accuracy conforming to IS:2281.

Test Cycle

• Start machine by ON push button. The clamping piston goes to bottom position and loading piston with indentor goes to the top position and the indentor shifts to indexed (fitted) position


• Push the cycle start button. The bottom piston moves up and the job is clamped against the clamping cone with a force of 500 kg.Then the loading piston moves down. The indentor shifts to its vertical position and the set load is applied on the test piece a light signal is provided which glows when the load is applied. The applied load is kept constant for a pre set time. Then the loading piston moves up and the indentor is indexed so that the impression is visible on the screen. Measure the impression by the micrometer.


• Push the de-clamp button.


• Unload the job and machine is ready for next test.

(Dimensions and Photographs are for reference pupose only there may be variation at the time of supply due to constant R &D)

The resistance to breakage by flexural shock of plastics and Electrical insulating materials as indicated by the energy extracted from standardized pendulum type hammers mounted on standardized machines in breaking standard specimens with pendulum swing. The energy absorbed per unit of specimen width is reported in joules.

Fully digital display (LCD) of angle and energy in joules Range change by selector switch. Interchangeability of impact hammers is very easy.

Max. Available energy - 21.68 Joules

Ranges - 0-2.71 J 0-5.42 J
0-10.84 J 0-21.68 J

PENETROMETER WITH BATH FOR BITUMEN & TAR(Analog Version) Penetrometer with bath for Bitumen &Tar Test : As per IS: 1203/1978
Use: Used for the determination of penetration of asphaltic bitumen and fluxed asphalt and blown type bitumen, Petroleum wax & jelly.
Description: Bath Unit consists of container of 20cm (H) x20cm (W) x35cm (L) Argon welded, needle, SS Cup 55mmdiax35mm (H) 8No. Transfer dish4No., Water bath Inner of SS304 and outer powder coated finish with motorized stirrer cum pump and a flange type hot+cold zone immersion SS304 heater of 1.5 Kw rating to maintain desired temp.
Temp. Range: 0C-95C, having cooling & heating arrangement controlled by a Digital Temperature controller cum indicator with PT-100 Sensor, Continuous duty Kirloskar compressor for cooling, electrically operated DC 230V plunger, penetration indicator between 225&350, Needle with 50 gms. and 100 gms. weights and timing device. Digital penetrometer for direct readout of penetration having Encoder & Decoder arrangement with digital timer 9.9 sec Max. The whole unit is mounted on castor wheels for easy movability.
Microprocessor based unit provides automatically timed operator programmable penetration measurements
Conforms to all ASTM, IP, ISO 9001 and related specifications Unit tests the consistency of lubricating greases, petroleum waxes, bitumens, pastes, creams and other solid to semisolid products, including a variety of food products. Microprocessor control provides a full range of measurement and reporting options The penetrometer defaults to the standard ASTM interval of 5 seconds, or the operator may program a different interval in the range between 0.1 and 999.9 seconds. All selected parameters are retained in memory and automatically repeated in subsequent tests until changed by the operator. Penetration measurements in the full range of 0-400 in 1/10 mm scale are reported in either 1/10 mm or 1/100 mm increments at the operators option. If a test result falls outside of the programmed range, an audible signal and visual error message alert the user of a failed sample. Results can be communicated to a printer or computer via a built in interface. Illumination with magnifying glass is also provided. Fine adjustment of the tip of the needle is also provided. Leveling indicator is also given. Built in DC operated Plunger is also incorporated with UNIT.Power:230V50Hz
BASIC MANUAL (DIAL TYPE) PENETROMETER(With all standard accessories)(Standard accessories includes Needle, Cone with Needle, 50/100gms wts, Plates, Cylindrical Container, Sample Container)
SS Bath (with Heating/cooling) digital temp. controller PT-100 Sensor for bath, transfer dish(8nos), Pump cum Stirrer-( Only Dig PID Microprocessor Controller with AUTOTuned type for Bath Temp Control, Range +2*C to 98*C )
BASIC Manual PENETROMETER WITH BATH (heating) digital temp. controllerPT-100 Sensor for bath, transfer dish(8nos), Pump cum Stirrer and Spring loaded needle & std accessories)( Only Dig PID Microprocessor Controller with AUTO Tuned type for Bath Temp Control )
DIGITAL PENETROMETER WITHOUT BATH but with Electrically Operated DC Plunger& All std accessories , Illumination, Magnifying glass, Leveling tube DIGITAL PENETROMETER (with Electrically Operated DC Plunger& All std accessories , Illumination, Magnifying glass, Leveling Tube) WITH BATH (heating/cooling), digital temp. controller PT-100 Sensor for bath, transfer dish(8nos), Pump cum Stirrer.Manual Penetrometer: As per IS: 1448[P 93]:1979 / IS: 1203:1978 / ASTM D 1321-76 / ASTM D 217.

The Universal Penetrometer is employed for testing a wide variety of materials as measured by penetration of weighted needles or cones. Main applications are for bituminous materials, but waxes, greases, foods, and pharmaceuticals are among other products tested. Penetration is read from a 5" (127mm) diameter indicator dial of 0-400 divisions, each representing 0.1mm of penetration. Global offers heavy-duty units for manual and automatic use and a lighter, portable model for field work or for users with limited work load or limited budget. All meet ASTM and IS standards when fitted with proper needle or cone.
The unit is ruggedly constructed for accurate, sensitive measurements. The aluminum base has a machined, grooved table with leveling screws for fine adjustments of tips of needles, cones and a spirit level. A robust stainless steel rod act as a support guides for a cast aluminum head with coarse adjustments & a movable table with rotating knob for fine adjustments to level the meniscus of specimen and a calibrated friction-free plunger mechanism. Indicator dial has instant zero reset. Any needle or cone with standard 1/8" (3mm) diameter stem may be mounted to the 47.5g plunger assembly. A standard 2.5g needle and two additional loading weights (50g, 100g) are included. Needles or cones for other tests can be provided separately as needed. Overall dimensions are 10.5x13x22" (267x330x559), (W x D x H) approx.
The Automatic model is the same as the manual unit, but has a button release mechanism with digital timer & DIGITAL read out for penetration to automatically stop the plunger when the preset time from 0.1 to 9.9 sec. expires with audible buzzer sound.
The penetration needle for bituminous materials is smooth, hardened, tempered stainless steel with brass ferrule and weighs 2.5g to give 50g total when mounted. Stainless steel wax penetration needle is also 2.5g but has truncated coneshaped tip with approx. 4mm maximum diameter tapered to 0.15mm diameter end. several types of 102.5g grease cones as having polished 90 cone with 30 removable hardened steel tip are available.
Standard accessories includes:1no spring loaded Plunger, 1no each wts of 50 & 100gm, 1no of Needle, 1no Sample Container (Manual Unit including all standard accessories) & Calibretion
Extra for Electrically operated Plunger for release of needle/cone.
Extra for Digital Timer.
POWER:230V, 50 Hz(If opted for Electrical Plunger & Dig.Timer with Buzzer Alarm)
CONES, NEEDLES AND ACCESSORIES:Use with Digital/Manual Pentrometer to determine the consistency of petroleum products, wide range of penetration types are available ( also for non-petroleum samples , see below). (For Grease) (For Bitumen) (For Grease) (For Wax)
Optional: (If required additional)
1. Weights of 50/100 gms, duly chrome plated and slotted for loading. 2. Hardened needle as per IS standard, GC 2131 per needle. For GC 2121 (HOLLOW CONE of BRASS duly Nichal/Chrome Plated weighing 2.5gms) per needle 3. Brass solid cone as per IS standard. (Used only for Wax/Grease penetration GC 2141/2142)) 4. SS container As per IS STD (35 mm Ht. x 56 mm Dia.) for bituminous sample. 5. SS /Brass Chrome Plated Cylindrical Container As per IS STD with inside thread for Wax 6. SS/Brass Base Plate Chrome plated As per IS STD for Wax 6. Provision for Illumination with magnifying glass 7. SS Standard Block for Calibration Purpose of Penetrometer (5mm, 10mm, 15mm, 20mm) 8. Dimensional Calibration Charges extra for accessories For Cone, For rest

• Testing range is very wide, from soft metal such as lead up to the hardest, like hardened steel


• Thin sheet metal is perfectly tested because the load applied is very small


• Same hardness number is obtained on the same specimen, regardless of the load applied.


• Built in projection screen to get accurate result

Vickers as well as Vickers cum Brinell Hardness Testersare suitable for Vickers and Brinell hardness of steel and other metals. These machined are designed and manufactured for very high accuracy, reliability and ease of operation. The selection of load is effected with the push button control system. The measurement of diagonal / diameter of indentation is done with the help of built-in optical system with graduated readout with micrometer. After taking indentation on the work piece, the objective lens is automatically swivelled into position and image of indentation appears on the focusing screen fitted in front of the machine. A push button is provided for starting the loading cycle and unloading is accomplished though hand lever.

This machine conforms to IS:1754-1986 for Vickers and IS: 2281-1983, BS: 240 for Brinell Test.

• Motorized system for application and removal of major load


• Minor load setting by LED bar graph


• Keyboard entry for scale selection


• Hi-Low-OK indication for hardness value


• Easy to read, large size extra bright 7 segment display


• Centronics parallel port for connecting Dot Matrix Pinter


• Sufficient error codes for smooth functioning of machines


• Serial interface (Optional)


• Least Count 01 for Rockwell and 0.2 for Rockwell Superficial


• Dwell Time 1 to 99 Seconds


• . Scale Displayed A, B, C, D, E, F, G, H, K, L, M, N, P, R, S, V in Nos. 1 to 15 Resp. and 15N, 30N, 45N, 15 T, 30T, 45T in Nos. 1 to 21 Resp. for Superficial


• Indenter is guided in linear bearing facilitates to test small jobs

The device works with both ultrasonic contact impedance (UCI) and dynamic (Leeb) probes. User get the benefits of two methods of measurement it is the maximum that can be obtained from a portable hardness tester.

Dynamic (Leeb) probe is used for measuring the hardness of non-ferrous metals, cast iron, coarse-grained materials, massive products etc.

The ultrasonic contact impedance (UCI) probe is used for measuring the hardness of small items, objects with a thin wall, complex form, and to measure the hardness of surface hardened layers.

Standard set of Hardness Tester-

Electronic unit, UCI probe, Leeb probe, 2 batteries AA, Charger, USB cable, Operating manual, Software for PC, Case.

Available options for ordering of Hardness Tester

UCI probe, Leeb probe, Batteries, Charger, USB-cable, Set of measures of hardness, Case

UCI Hardness Tester is designed for rapid non-destructive testing of hardness.Metals and alloys on standardized international scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV);

The ultrasonic contact impedance (UCI) probe is used for measuring the hardness of small items, objects with a thin wall, complex form, and to measure the hardness of surface hardened layers.

Measurement hardness range:

• Rockwell, HRC - 20 - 70


• Brinell, HB - 90 - 450


• Vickers, HV - 230 - 940

Standard set of UCI Hardness Tester

• Electronic block


• UCI probe


• 2 batteries AA


• Charger


• USB cables


• Operating manual


• Software for PC


• Case

Measuring the hardness of the surface hardened layer Possibility to use in field conditions with high humidity and dust Convenience and ease of measurement Optimized number of buttons Contrast display with bright back-lighting Automatic recognition of probe Indication of the type of connected probe Calibrations stored in memory of probe Very easy in operation and calibration Internal memory and communication with PC Rubber bumper protected case

Micro Vickers Hardness Tester designed to cater heavy duty and research work with all the necessary automation for loading and measurements.

Test Load- 10gf to 1000 gf (0.098, 0.246, 0.49, 0.98, 1.96, 2.94, 4.9, 9.80 N) 10, 25, 50, 100, 200, 300, 500, 1000 gmf dial switchable.

Dwell time - 5 - 60 Seconds.

Loading Mechanism Motorized loading and releasing.

Indexing- Rotating turret for indenter and objective lens.

Objective For scanning 10 x, Plan achromatic 0.25 NA.

For measurement 40 x, Plan achromatic 0.4 NA.

Diagonal Reading - Manual Filler micrometer eyepiece (10 X) with 0.5 Micron accuracy OR Digital measurement with the help of Digital Filler micrometer eyepiece (10 X) with 0.025 Micron accuracy.

Computerised Attachment:With this attachment one can convert manual hardness to computerized one. This has many advantages like higher accuracy as of bigger indentation, operator ease as one can get the Microhardness value by just clicking two diagonals of indentation image on the screens. Further one can get plot of effective case depth graph. All the readings with image and graphs can be stored, printed. This model MVH-II consists of

• 1/2" CCD Camera (High resolution monochrome) with interface adaptor


• Image grabber hardware.


• Dedicated image processing Software for Vickers Hardness number, effective case depth hardness graph. Hardness Conversion facility.

Rockwell, Rockwell cum Brinell, Rockwell cum Rockwell Superficial

Hardness Testers are designed and developed after years of experience in this field. All the models are manufactured under strict quality control at all manufacturing stages.

These models are suitable for testing hardness of metals and alloys of all kinds, hard or soft, whether flat or round etc. or of irregular shape. These testers are simple in design and easy to operate, still yet quite sensitive and accurate.

These models strictly conforms to IS: 1586-2000, BS: 891 part 1 & 2 for Rockwell & Rockwell superficial test. IS: 2281-1983, ASTM-E-10 for brinell test.

Automatic weight selection with automatic zero setting dial gauge.
Automatic weight selection with automatic zero setting dial gauge with more testing height and throat

Automatic weight selection with automatic zero setting dial gauge.
Arrangement similar to RS with two additional weights of 185.5 kgf and 250 kgf for brinell tests.
On this machinesmall pin having Dia 2 mm can be tested as plunger is guided with a set of six bearings.

This hardness tester is similar above machine in construction, and with automatic weight selection. This is useful for carrying Rockwell and Rockwell Superficial tests. The Rockwell Superficial method is useful for checking hardness of very thin sheets and surface hardness.

Application and removal of major load is motorized. Motorized models have semi automatic operations for products testing. Drive motor-single phase, 230-V, 50 cycles AC.

Mainly used to check hardness in confined spaces, on large & heavy components, permanently installed parts with low test expenditure. The machine has built in conversion facility for given material to convert D value to Vickers (HV), Rockwell (HRB, HRC), Brinell (HB), UTS scales which can be selected by pressing arrow keys. 30 hardness scales for different probes selectable by feather touch keys. Alpha numeric display 16 characters x 2 lines user friendly software. Display indicates selected material & scale combination & hrdness value. Facility to connect dot matrix printer Upto 100 readings can be stored.

This instrument measures the rate of extrusion of Molten resins through a die of specified length and diameter under prescribed conditions of temperature, load, piston position.

Instrument with following accessories will be supplied Digital stop watch, Temp. Controller ( PID ), Piston, Orifice remove, Barrel Cleaner,

Brinell hardness tester, are designed for Brinell hardness measurement on steels and other ferrous materials and also on non ferrous materials like Brass, Bronze, Aluminum, etc. the material can be cast, forged or rolled and the shape can be flat, round irregular.

The actual load application system is of dead weight type combined with mechanical lever system. The supporting hydraulic system is for initial of load before each test and damping the load application system for smooth application of load.

A separate hydraulic power pack, positioned in the bottom part of the machine increase the machine stability.

Design of a floating fulcrum lever system ensures high accuracy and dependability.

The machine accuracies confirm to IS: 2281-2005 & BS: 240

AUTOMATIC OPTICAL BRINELL HARDNESS TESTERS

• The machine has a robust, C-type load frame & has been designed for production testing of cast or forged components like leaf springs, cam shafts, etc. for Brinell hardness value. This machine is suitable for foundries, engineering industry on production line.


• Since most of the operations are fast and automatic, the test speed is high with less operator fatigue.


• The cycle time (except loading / unloading) is about 12 seconds per test.


• Load stages 750 kgf and 3000 kgf.


• Optical measuring equipment with 14 X magnification.


• Job loading / unloading, push button operation, pushing cycle start, de-clamp buttons are only manual operations & rest all is automatic.


• A push button is pressed for cycle start & hydraulic operations. After cycle time, impression is visible on screen, which (Diameter) is to be measured with the help of microscope of least count 0.01mm.


• Computerized model is available .Computerized model has built in CCD and suitable advanced software. Hardness will be displayed On computer monitor automatically. Results printout can be taken.


• Accuracy conforming to IS:2281.

Test Cycle

• Start machine by ON push button. The clamping piston goes to bottom position and loading piston with indentor goes to the top position and the indentor shifts to indexed (fitted) position


• Push the cycle start button. The bottom piston moves up and the job is clamped against the clamping cone with a force of 500 kg.Then the loading piston moves down. The indentor shifts to its vertical position and the set load is applied on the test piece a light signal is provided which glows when the load is applied. The applied load is kept constant for a pre set time. Then the loading piston moves up and the indentor is indexed so that the impression is visible on the screen. Measure the impression by the micrometer.


• Push the de-clamp button.


• Unload the job and machine is ready for next test.

(Dimensions and Photographs are for reference pupose only there may be variation at the time of supply due to constant R &D)

The resistance to breakage by flexural shock of plastics and Electrical insulating materials as indicated by the energy extracted from standardized pendulum type hammers mounted on standardized machines in breaking standard specimens with pendulum swing. The energy absorbed per unit of specimen width is reported in joules.

Fully digital display (LCD) of angle and energy in joules Range change by selector switch. Interchangeability of impact hammers is very easy.

Max. Available energy - 21.68 Joules

Ranges - 0-2.71 J 0-5.42 J
0-10.84 J 0-21.68 J

PENETROMETER WITH BATH FOR BITUMEN & TAR(Analog Version) Penetrometer with bath for Bitumen &Tar Test : As per IS: 1203/1978
Use: Used for the determination of penetration of asphaltic bitumen and fluxed asphalt and blown type bitumen, Petroleum wax & jelly.
Description: Bath Unit consists of container of 20cm (H) x20cm (W) x35cm (L) Argon welded, needle, SS Cup 55mmdiax35mm (H) 8No. Transfer dish4No., Water bath Inner of SS304 and outer powder coated finish with motorized stirrer cum pump and a flange type hot+cold zone immersion SS304 heater of 1.5 Kw rating to maintain desired temp.
Temp. Range: 0C-95C, having cooling & heating arrangement controlled by a Digital Temperature controller cum indicator with PT-100 Sensor, Continuous duty Kirloskar compressor for cooling, electrically operated DC 230V plunger, penetration indicator between 225&350, Needle with 50 gms. and 100 gms. weights and timing device. Digital penetrometer for direct readout of penetration having Encoder & Decoder arrangement with digital timer 9.9 sec Max. The whole unit is mounted on castor wheels for easy movability.
Microprocessor based unit provides automatically timed operator programmable penetration measurements
Conforms to all ASTM, IP, ISO 9001 and related specifications Unit tests the consistency of lubricating greases, petroleum waxes, bitumens, pastes, creams and other solid to semisolid products, including a variety of food products. Microprocessor control provides a full range of measurement and reporting options The penetrometer defaults to the standard ASTM interval of 5 seconds, or the operator may program a different interval in the range between 0.1 and 999.9 seconds. All selected parameters are retained in memory and automatically repeated in subsequent tests until changed by the operator. Penetration measurements in the full range of 0-400 in 1/10 mm scale are reported in either 1/10 mm or 1/100 mm increments at the operators option. If a test result falls outside of the programmed range, an audible signal and visual error message alert the user of a failed sample. Results can be communicated to a printer or computer via a built in interface. Illumination with magnifying glass is also provided. Fine adjustment of the tip of the needle is also provided. Leveling indicator is also given. Built in DC operated Plunger is also incorporated with UNIT.Power:230V50Hz
BASIC MANUAL (DIAL TYPE) PENETROMETER(With all standard accessories)(Standard accessories includes Needle, Cone with Needle, 50/100gms wts, Plates, Cylindrical Container, Sample Container)
SS Bath (with Heating/cooling) digital temp. controller PT-100 Sensor for bath, transfer dish(8nos), Pump cum Stirrer-( Only Dig PID Microprocessor Controller with AUTOTuned type for Bath Temp Control, Range +2*C to 98*C )
BASIC Manual PENETROMETER WITH BATH (heating) digital temp. controllerPT-100 Sensor for bath, transfer dish(8nos), Pump cum Stirrer and Spring loaded needle & std accessories)( Only Dig PID Microprocessor Controller with AUTO Tuned type for Bath Temp Control )
DIGITAL PENETROMETER WITHOUT BATH but with Electrically Operated DC Plunger& All std accessories , Illumination, Magnifying glass, Leveling tube DIGITAL PENETROMETER (with Electrically Operated DC Plunger& All std accessories , Illumination, Magnifying glass, Leveling Tube) WITH BATH (heating/cooling), digital temp. controller PT-100 Sensor for bath, transfer dish(8nos), Pump cum Stirrer.Manual Penetrometer: As per IS: 1448[P 93]:1979 / IS: 1203:1978 / ASTM D 1321-76 / ASTM D 217.

The Universal Penetrometer is employed for testing a wide variety of materials as measured by penetration of weighted needles or cones. Main applications are for bituminous materials, but waxes, greases, foods, and pharmaceuticals are among other products tested. Penetration is read from a 5" (127mm) diameter indicator dial of 0-400 divisions, each representing 0.1mm of penetration. Global offers heavy-duty units for manual and automatic use and a lighter, portable model for field work or for users with limited work load or limited budget. All meet ASTM and IS standards when fitted with proper needle or cone.
The unit is ruggedly constructed for accurate, sensitive measurements. The aluminum base has a machined, grooved table with leveling screws for fine adjustments of tips of needles, cones and a spirit level. A robust stainless steel rod act as a support guides for a cast aluminum head with coarse adjustments & a movable table with rotating knob for fine adjustments to level the meniscus of specimen and a calibrated friction-free plunger mechanism. Indicator dial has instant zero reset. Any needle or cone with standard 1/8" (3mm) diameter stem may be mounted to the 47.5g plunger assembly. A standard 2.5g needle and two additional loading weights (50g, 100g) are included. Needles or cones for other tests can be provided separately as needed. Overall dimensions are 10.5x13x22" (267x330x559), (W x D x H) approx.
The Automatic model is the same as the manual unit, but has a button release mechanism with digital timer & DIGITAL read out for penetration to automatically stop the plunger when the preset time from 0.1 to 9.9 sec. expires with audible buzzer sound.
The penetration needle for bituminous materials is smooth, hardened, tempered stainless steel with brass ferrule and weighs 2.5g to give 50g total when mounted. Stainless steel wax penetration needle is also 2.5g but has truncated coneshaped tip with approx. 4mm maximum diameter tapered to 0.15mm diameter end. several types of 102.5g grease cones as having polished 90 cone with 30 removable hardened steel tip are available.
Standard accessories includes:1no spring loaded Plunger, 1no each wts of 50 & 100gm, 1no of Needle, 1no Sample Container (Manual Unit including all standard accessories) & Calibretion
Extra for Electrically operated Plunger for release of needle/cone.
Extra for Digital Timer.
POWER:230V, 50 Hz(If opted for Electrical Plunger & Dig.Timer with Buzzer Alarm)
CONES, NEEDLES AND ACCESSORIES:Use with Digital/Manual Pentrometer to determine the consistency of petroleum products, wide range of penetration types are available ( also for non-petroleum samples , see below). (For Grease) (For Bitumen) (For Grease) (For Wax)
Optional: (If required additional)
1. Weights of 50/100 gms, duly chrome plated and slotted for loading. 2. Hardened needle as per IS standard, GC 2131 per needle. For GC 2121 (HOLLOW CONE of BRASS duly Nichal/Chrome Plated weighing 2.5gms) per needle 3. Brass solid cone as per IS standard. (Used only for Wax/Grease penetration GC 2141/2142)) 4. SS container As per IS STD (35 mm Ht. x 56 mm Dia.) for bituminous sample. 5. SS /Brass Chrome Plated Cylindrical Container As per IS STD with inside thread for Wax 6. SS/Brass Base Plate Chrome plated As per IS STD for Wax 6. Provision for Illumination with magnifying glass 7. SS Standard Block for Calibration Purpose of Penetrometer (5mm, 10mm, 15mm, 20mm) 8. Dimensional Calibration Charges extra for accessories For Cone, For rest

• Testing range is very wide, from soft metal such as lead up to the hardest, like hardened steel


• Thin sheet metal is perfectly tested because the load applied is very small


• Same hardness number is obtained on the same specimen, regardless of the load applied.


• Built in projection screen to get accurate result

Vickers as well as Vickers cum Brinell Hardness Testersare suitable for Vickers and Brinell hardness of steel and other metals. These machined are designed and manufactured for very high accuracy, reliability and ease of operation. The selection of load is effected with the push button control system. The measurement of diagonal / diameter of indentation is done with the help of built-in optical system with graduated readout with micrometer. After taking indentation on the work piece, the objective lens is automatically swivelled into position and image of indentation appears on the focusing screen fitted in front of the machine. A push button is provided for starting the loading cycle and unloading is accomplished though hand lever.

This machine conforms to IS:1754-1986 for Vickers and IS: 2281-1983, BS: 240 for Brinell Test.

• Motorized system for application and removal of major load


• Minor load setting by LED bar graph


• Keyboard entry for scale selection


• Hi-Low-OK indication for hardness value


• Easy to read, large size extra bright 7 segment display


• Centronics parallel port for connecting Dot Matrix Pinter


• Sufficient error codes for smooth functioning of machines


• Serial interface (Optional)


• Least Count 01 for Rockwell and 0.2 for Rockwell Superficial


• Dwell Time 1 to 99 Seconds


• . Scale Displayed A, B, C, D, E, F, G, H, K, L, M, N, P, R, S, V in Nos. 1 to 15 Resp. and 15N, 30N, 45N, 15 T, 30T, 45T in Nos. 1 to 21 Resp. for Superficial


• Indenter is guided in linear bearing facilitates to test small jobs