Post Your Requirement Menu

Welcome User

Transformers

Our Complete range of products are Distribution Transformers, resin cast control transformer, Core Balance Current Transformer, Industrial Isolation Transformer and Auto Transformer.

Distribution Transformers

  • Frequency 50 Hz, 60 Hz
  • Ratings Upto 2.5 MVA
  • Applicable Standards IS, IEC, BS etc.
  • Cooling ONAN, OA
  • Insulating Fluid Mineral Oil to specification
  • Polarity As specified
  • Primary voltage Upto 33 kV
  • Secondary Voltage 433 V (Other Voltages as required)
  • Winding material Copper / Aluminium
  • Taping range 5% in steps of 2.5% (Other tapings as required)
  • Impedance In line with applicable standards.

Our Power Distribution Transformer is used to provide final voltage transformation in the electric power distribution system. It settles down the voltage used in distribution line to the level which is used by the customers. If it is mounted on the utility pole it is known as pole mount transformer and if it is located at ground level or underground and mounted on create pad is known as pad mounted transformer. The Distribution Transformers are designed by using iron as they are operated for 24 hours. It carries maximum efficiency at lower loads which is about 60 or 70% of full or even less load. Further, the voltage regulation in these transformers is kept minimum for better efficiency.

View Complete Details

resin cast control transformer

Transformers are electric equipment that changes the voltage and the current of electricity to facilitate its efficient transmission and distribution. Transformers are commonly used at power generation facilities to increase voltage and to decrease current in order to transport electric energy across transmission lines. When the electricity reaches the end user, transformers are used to reduce voltage and to increase current to make the electricity suitable for general use. The process of transforming voltage results in energy loss that is released in the form of heat and therefore transformers must contain effective cooling systems. Transformers are differentiated by their cooling systems (this is one of several ways that the transformer industry classifies its products). Dry type transformers dissipate heat directly into the ambient air. Liquid cooled transformers (e.g. oil filled transformers) dissipate heat into liquid mediums.

View Complete Details

Core Balance Current Transformer

  • System voltage 11KV
  • Ratio 200/1 “ 1 “ 0.577 A

The Core balance CT is used for various application in various industries. The product is made available to the market in various specifications. It is developed in conformation with international standards of quality by utilizing high grade raw material.

View Complete Details

Industrial Isolation Transformer

Precisely engineered in accordance to the set industry norms, the offered Industrial Isolation Transformer is valued for its easy operation, thermal stability and consistent performance. To ensure a defect-free range, the Industrial Isolation Transformer undergoes rigorous quality assurancetesting procedures.

View Complete Details

Auto Transformer

Control Transformers Are To Supply Power To Control And Or Auxiliary Equipment Not Intended For Direct Connection To The Main Source. Control Transformers Are Specifically Used To Provide Control Supply Voltage For The Control Circuits Of Ac Motor Starters, I.E. Starter Coils, Timers, Indicating Lamps Electronics Protection Relays Etc. Control Transformers For Contractor Applications Have To Energize The Coil And Maintain A Contact For Definite Period Of Time. The Initial Energizing Of The Coil Takes 5 To 40 Mil. Seconds And Requires 3 To 10 Times The Normal Current. While Calculating The Va Rating Of The Control Transformer, This Factor Should Be Taken In To Account. They Are Available For Single Phase And Three Phase Inputs And Are In The Range From 15 Va To 30 Kva.

View Complete Details

Constant Voltage Transformer

  • Input Voltage 180 V- 260 V
  • Output Voltage 220-230 (+ -) 1%
  • Efficiency 90% (approx) under full load conditions.
  • Effect of Frequency 1.6 (approx) change in output voltage for every 1% change in line frequency.
  • Line Frequency 50 Hz
  • Output Step 2 Cycle (30 to 40 Load Response milliseconds).
  • Output Wave Form Sinewave
  • Wave form Distortion 5% (approx) under full load conditions.
  • Load Power Factor 0.75% lag to 0.9% lead
  • Ambient Temperature -10oC to 50oC
  • Transformer Type Ferro-Resonant

We are dealing in well designed range of Constant Voltage Transformer. The transformer is developed with modern machine and tools and catering to huge demand of diverse industries. The product is used with advanced electronic instruments such as microprocessor and computers. The range is available from 75 KVA to 10 KVA as per need. It has higher input voltage control range helping in loading less rated low short term over load capacity.

View Complete Details

Battery Charger Transformer

We are reliable manufacturer, supplier and exporter working from India. We deal in wide assortment of Battery Charger, which is developed with best grade of raw material. It is available to the customers in various forms such as SMPS battery, 12VDC24VDC36VDC automatic battery charger, automaticmanual battery charger, 110 VDC240 VDC automaticmanual charger, etc. Also, the numerous quality tests are conducted on this charger before the delivery.

View Complete Details

Tell Us What are you looking for? Will call you back

Contact Us

  • Mr. Gaurav Saini
  • 1- Plot No -383, Rampura Delhi, 110 035, Delhi, Delhi - 110035, India