Interlogicx Embedded Solutions

Chinna Kalapet, Pondicherry

Package Includes
Fully Assembled and Tested Development Board with Xilinx XC3S100E FPGA core processor
Parallel Port JTAG Cable for program downloading.
CDROM containing XILINX ISE - Programming Software and User Manual
Power Adaptor.

Introduction
ILXSPARTAN100E is a development board for XILINX FPGA core processor. The board supports on board JTAG for programming via the board's parallel port. All the I/O ports are accessible via standard external headers for easy interfacing of external devices.

Features

• Built-in LEDs for port output debugging
• Output Headers provide access to all port pins for easy interfacing to external devices
• Target XILINX FPGA XC3S100E is supplied with kit.
• On-Board RS232 Port for direct connection to PC's Serial Port
• .Bit file for FPGA and .mcs file for PROM can be downloaded easily with the help of a user-friendly XILINX ISE Software

Specifications

• 2160 logic elements
• Four 18K-bit block RAM(72K bits)
• Four 18x18 pipelined hardware multipliers.
• Two clock DCMs.
• 24 mhz crystal clock frequency(max 300mhz)
• Operating temperature range is 0o c 85o c.
• Speed grade is -4.

XILINX ISE

• Programs .bit and .mcs files.
• Straight forward and intuitive user interface
• Requires parallel port of PC for operation
• Three simple steps to program the device.

System Requirements

• Windows 95/98/ME/NT/2000/XP/2007/linux
• Parallel Port
• For Spartan 3E minimum 180MB and max 760MB RAM of 32 bit windows OS
• 2GB Disk Space

ILPMCSPRO is a Device Programmer Board for Programming the flash memory of major Atmel 89 Series Microcontrollers, Ideally suited for Project Deployment .Simple to use & low cost, yet powerful flash microcontroller programmer for the Atmel 89 series. It will Program, Read and Verify Code Data, Write Lock Bits, Erase and Blank Check.
All fuse and lock bits are programmable. This programmer has intelligent onboard firmware and connects to the serial port. It can be used with any type of computer and requires no special hardware.
All that is needed is a serial communication port which all computers have.
The programmer connects to a host computer using a standard RS232 serial port. All the programming 'intelligence' is built into the programmer so you do not need any special hardware to run it. Programmer comes with window based software for easy programming of the devices

Features
Supports major Atmel 89 series devices
Auto Identify connected hardware and devices
Built - in Error checking , verification and Lock facilities
20 and 40 pin ZIF socket on-board
Programming in auto mode.
On-Board RS232 Port for direct connection to PC's Serial Port
Hex file can be downloaded easily with the help of a user-friendly JetFlashex Software

List of Supported Microcontrollers
AT89C51, AT89LV51, AT89C52, AT89LV52, AT89C55
AT89LV55, AT89S51, AT89LS51, AT89S52, AT89LS52
AT89S53, AT89LS53, AT89S8252, AT89LS8252, AT89C1051
AT89C2051, AT89C4051

JetFlasheX
Programs Intel Hex files.
Straightforward and intuitive user interface
Requires RS-232 port of PC for operation
Three simple steps to program the flash device.

System Requirements
Windows 95/98/ME/NT/2000/XP
RS-232 Port
16MB RAM
3MB Disk Space

Package Includes
Fully Assembled and Tested Development Board with LPC1114 Microcontroller
Serial Port Cable for PC interfacing and programming
CDROM containing Flash Magic Programming Software and User Manual

Introduction
InterLogicx ILXLPC1114 is a development board for NXP LPC1114 microcontroller. The ILXLPC1114 board supports on board ISP Circuit for programming Flash memory via the boards RS232 port eliminating the need for separate device programmer. On-board switch toggles between programming and code execution modes. All the microcontrollers I/O ports are accessible via standard external headers for easy interfacing of external devices.

Features

Easy programming of the flash memory with a serial port of a computer.
Toggling between programming/execution modes with a single switch eliminating the need for any complex changes in the hardware.
Output Headers provide access to all port pins for easy interfacing to external devices
Target embedded microcontroller LPC1114 is supplied with kit.
On-Board RS232 Port for direct connection to PCs Serial Port
Hex file can be downloaded easily with the help of a user-friendly Flash Magic Software

Specifications

ARM Cortex-M0 processor, running at frequencies of up to 50 MHz
32KByte on-chip Flash ROM with In-System Programming (ISP) and
In-Application Programming (IAP) via 12KByte On-Chip Boot loader, 4KByte SRAM,
Nested Vectored Interrupt Controller, 1 SSP controller
UART with full Modem Interface and RS485 Support
Fast Mode I2C-Bus, 4 Timers with 4 capture channels and 13 output channels
Watchdog (WDT), System tick timer, 10-bit ADC with 8 channels, 42 GPIO, Serial Wire Debug/Trace port.

Applications
Access control
Point-of-sale
Communication gateway
Embedded soft modem
General purpose applications


Programs Intel Hex files
Straightforward and intuitive user interface
Requires RS-232 port of PC for operation
Five simple steps to program the flash device


System Requirements
Windows XP /7
RS-232 Port
16MB RAM
3MB Disk Space

Fully Assembled and Tested Single Channel ADC Board with temperature sensor
8 pin and 2 pin Flat Cable Connectors for interfacing.

Features

• Single channel ADC
• Conversion Time =