Jain Tubes

Bharat Nagar, Bhopal, Madhya Pradesh

We are the main supplier of this product.

We are among the major players in the market offering top-notch Butterfly Valve and that too at marginal prices. We source the raw material from the leading vendors and manufacturers in the market; thus, we are capable of fulfilling the exact requirements of the clients with our offered products. Features: Temperature Range 34^oC to 150^oC No part in contact with fluid except disc and liner Self lubricated bushes Neck flange according to ISO:5211 Direct Actuator mountable design Design reference IS:13095 & BS:5155 Neck height to accommodate insulation Lugs on body make them suitable for using at the end of line Suitable for actuator & gear mountings 100% leak tight design Available in lever type and clutch type handles Each valve is factory tested to 110 percent of specified pressure rating. Extended neck allows adequate clearance for flanges and insulation. Round, polished disc and hub edge provides 360 degree concentric seating, minimum flow restriction, lower torques and longer seat life. Cast-in top mounting plate is an integral part of the body which is standardized to allow direct mounting of all kind of actuators.

Suggested Operation : For PN10 & PN16 : Upto 150mm Hand Lever Types End connection: Flanged / Lug / Wafer Over 150mm : Gear or Actuator K-701 (with CF8 disc) K- 702 (with CF8M disc)

Fret not! We are here to help you out with the payment procedures. Be it online or offline payment method, we are here to assist you all the way through the payment process. Development of modular control inside our warehouse helps in proper organization of the products and ensure complete safety while storage. The entire system is properly managed by our warehousing experts.

Features : Strictly conforming to IS : 4038 Available in rubber seating Available in swing type & lift type design Swing type Screwed 15mm to 150mm Swing type Flanged 50mm to 300mm Lift type Screwed & Flanged 25mm to 100mm Valves upto 150mm have single circular door Valves above 150mm have two semi circular doors Valve designed for almost full flow rate

Test Pressure : Body : 1.5 MPa Seat : 1.0 MPa 1 Bar = 0.1 MPa = 1.019 Kg/cm² = 14.50 PSI K-518 Single Disc Design K-519 Double Disc Design

Working in assistance with a brilliant inventory management system and capacious storehouse has enabled us to entertain urgent and massive requirements of the customers. With a well-organized set up, we serve our buyers from Bhopal(India) to every nook and corner.

Features : Available in outside yoke type rising stem Flanged ends Handwheel, cap or gear operated Available in PN10 & PN16 ISI Marked as per IS:14846 Available in CL125 as per BS:5163 Available in reselient seating as well as metal seating Working And Test Pressure: Sluice Valve PN 1.0 Sluice Valve PN 1.0 Gate Valve CI 150 Hydrostatic Test (Mpa) Body / Shell 1.5, 2.4, 3.0 Hydrostatic Test (Mpa) Seat 1.0, 1.6, 2.2 Pneumatic Test (Mpa) Seat NA, NA, 0.7 1 Bar = 0.1 Mpa = 1.019 Kg.cm2 = 14.50 PSI K-501 Cast Iron Sluice Valve Non Rising Stem PN 10 with cap K-502 Cast Iron Sluice Valve Non Rising Stem PN 10 with Handwheel K-503 Cast Iron Sluice Valve Non Rising Stem PN 16 with cap K-504 Cast Iron Sluice Valve Non Rising Stem PN 10 with Handwheel K-504O Cast Iron Sluice Valve Non Rising Stem PN 10 with Handwheel but for Open End Applications. K-509 Ductile Iron Sluice Valve Non Rising Stem PN 16 with Handwheel K-510 Ductile Iron Sluice Valve Rising Stem PN 16 with Handwheel

We make available premium quality Cast Iron Valves in varying sizes. Assistance of warehouse management software helps in minimizing the efforts of the personnel and ensures the safe storage of the lot. Moreover, our experts keep a stringent check over the same. We have developed robust payment processing procedures to facilitate safe and quick exchange of the trade.