Our Products
Standard Supply:
Main drive Motor
Electric control panel with INCH & SINGLE CYCLE AUTO OPERATION
Stroke adjustment rod with Limit Switch
Blade mounting with machine
Application:
Angle Cutting.
Down stroking, Electric/Hydraulic closed loop servo valve controlled.
Two axis independent ram control (Y1 & Y2), ram is fully guided throughout the entire stroke, guides do not require lubrication and linear encoders for ram feedback and positioning (.01mm/.0004")
High Speed, CNC back gauge (X), two finger stops with alenguide are standard (Optional R axis)
Esa 550c compact numerical control.
Two material support arms with alenguide.
The frame is an assembly of a heavy steel plate consisting of 2 side frames, a upper and lower cam plate, reinforced sheet-metal plate for the oil-tank and the hydraulic unit. After welding of the frame it is de-stressed. Some of the main features of this frame are:
The machined cylinder mount is a integral part of the side-frame.
The extra heavy side and rear plates provide superior frame stability.
Ram electrical / hydraulic closed-loop servo system
Main drive standard make motor
Electrical control panel with three speed inch, single cycle, Auto mode of operation.
Two front sheet supports
Manual back gauge with micro-adjusment swing stoppers. pair of lifting chains.
fine stroke adjustment rod with limit switches.
One suitable 5 way die and blade.
(segmented ofr full length, EN-9 not covered under warranty)
moveble console with emergency stop.
Tonnage indicating - adjustment device.
Manual centralized lubrication system with hand pump.
bending chart.
Mono Block Welded Steel Frame ultra tested-2062
steel plates rigid to provide Accurate bending.
All pivots have hardened of ground pin bushes of five
piece guide slide lubricated by central hand pump
Repetitive accuracy is within +0.03mm Ram travel parallelism with out using sensitive & complex servo Hydraulics.
Most reliable Hydraulic components & sealing for international reputed design for 350 bar against operating pressire of 160 bar maximum.
Three cycles operation inch, Single cycle&Auto for grater operator convenience.
Three speed operation reduces ideal travel time which improves productivity.
Bending force easily adjustable From front for forgue tool of bending material.
Cap . 20 ton to 500 ton
Application:- Punching - Forming - Straightening - Stamping - Embossing Cutting
Hydraulic Press
Cap . 20 ton to 500 ton
Application:- Punching - Forming - Straightening - Stamping - Embossing Cutting
No heat affected zones, dust or fumes
No tool sharpening
Low tangential Force on part
Small cutting width (Kerf)
Good cutting quality
High speed cuts in many materials
Cad/Cam Systems
Environmentally safe
High cutting speed
Standard Supply:
• Main drive Motor
• Electric control panel with INCH & SINGLE CYCLE AUTO OPERATION
• Stroke adjustment rod with Limit Switch
• Punch & Die Adaptor
Application
• Angle Cutting.
Specifications:
Capacity 120 Ton 220 Ton
Angle Size 90 x 90 x 10MM 150 x 150 x 16MM
Stroke of Cylinder 50 MM 50 MM
Oil Tank Capacity 160 Ltrs 160 Ltrs
Type of Operation Single Cut Type Single Cut Type
Motor Speed 7.5 H P (1440 RPM) 15 / 6 SPM
Working Pressure 220 Kg 220 Kg
Speed : Downward & Upward 15 /6 SPM 15 / 6 SPM
Working Height 850 MM 850 MM
Net Weight 1500 Kgs 2000 Kgs
• Main drive standard make motor
• Electrical control panel with three speed inch, single cycle, Auto mode of operation.
• Two front sheet supports
• Manual back gauge with micro-adjusment swing stoppers. pair of lifting chains.
• fine stroke adjustment rod with limit switches.
• One suitable 5 way die and blade.
• (segmented ofr full length, EN-9 not covered under warranty)
• moveble console with emergency stop.
• Tonnage indicating - adjustment device.
• Manual centralized lubrication system with hand pump.
• bending chart.
Feature:• Mono Block Welded Steel Frame ultra tested-2062
• steel plates rigid to provide Accurate bending.
• All pivots have hardened of ground pin bushes of five
• piece guide slide lubricated by central hand pump
• Repetitive accuracy is within +0.03mm Ram travel parallelism with out using sensitive & complex servo Hydraulics.
• Most reliable Hydraulic components & sealing for international reputed design for 350 bar against operating pressire of 160 bar maximum.
• Three cycles operation inch, Single cycle&Auto for grater operator convenience.
• Three speed operation reduces ideal travel time which improves productivity.
• Bending force easily adjustable From front for forgue tool of bending material.
• Main drive Motor
• Stamping Holder without stamp.
• Electric control panel with INCH & SINGLE CYCLE AUTO OPERATION
• Stroke adjustment rod with Limit Switch
Capacity 75 Ton 100 Ton
Press Type C – Type C – Type
Number Stamping : 08 Characters 12 Characters
Depth of Characters 1 MM (Adjustable) 1 MM (Adjustable)
Table Size: 500 x 300MM 500 x 300MM
Bolster Area (L.R. x F.B.) 600 x 200 MM 600 x 200 MM
Open Daylight 300MM 300MM
Throat Depth 250 MM 250 MM
Cyl Stroke: 100MM (Adjustable) 100MM (Adjustable)
Working Height: 750 MM 750 MM
Speed 25 Strokes/Min ( At 25mm Length) 25 Strokes/Min ( At 25mm Length)
Working Pressure 750 MM 750 MM
Oil Tank Capacity 160 Ltrs 200 Ltrs
Motor: 7.5 H P 10 H P
Standard Supply:
Blade Mounted with Machine
Stroke setting with Limit Switch
Electric control panel with INCH & SINGLE CYCLE AUTO OPERATION
Application
Angle Corner Cutting
"V" Notching
Specifications:
Capacity : 45 Ton : 70 Ton
Cutting Flange : 100MM x 10 MM Thik : 150 MM x 12MM Thik
Working Height : 850 MM : 850 MM
No of Stroke : 6 Strokes / Min (At 25MM Stroke Length) : 6 Strokes / Min (At 25MM Stroke Length)
Motor: : 7.5 H P : 7.5 H P
Working Pressure : 180 Kg : 180 Kg
Type of Operation : Vertical : Vertical