We offer Injection Grout which is a cementitious, high flow, expansive, non-shrink injection Grout. The Injection Grout is made available the popular brand Keminject - K5. Injection Grout (KEMINJECT-K5) is single component cement based expansive grout. Injection Grout is a very fine powder material when mixed with water exhibit flow like water and on curing instead of shrinkage shows positive expansion. The non-shrink characteristic makes it suitable for injection grouting of concrete structures such as buildings, bridges, dams, tunnels etc. On curing for 28 days it equals the strength of M-40 concrete.

Benefits

i>
• Single component, easily miscible with water.
• Very low viscosity after mixing with water helps in penetration of micro cracks of the concrete.
• Bonds strongly to old and new concrete internally.
• Provides 100% filling of cracks and pores.
• Expands on curing by the way of duel shrinkage compensation.
• Strength is much higher than the neat cement paste.
• Not only fills/seals the gaps, cavities and cracks, provides strength to the structure by consolidating it.
• Provides cent percent water proofing after grouting.
• Arrest incoming & outgoing water.
• Color - same as cement.
• Non toxic, non hazardous.

End Uses:

• Injection grouting of Building structures - roof, basement, water tank, swimming pool, toilet, bathroom etc.
• Bridges, dams & tunnels

Direction For Use

Preparation For Injection Grouting
Drill hole on the crack at every one meter in down direction, of the size depends on grouting nozzle size. The depth of the hole shall depend on thickness of the structural part. Clean the dust by air and then by water. Fix the proper size nozzle by using fast setting cement and / or epoxy sealant to cure for at least 24 hours before grouting.
Mixing

• Take clean water as per the w/p ratio into a plastic container (50 liter size).
• Start adding grout powder with continuous stirring to homogenous free-flowing thin slurry.
  Grouting
  Start injecting the mixed slurry by using grouting pump at a pressure of 3-5 kg /cm² till the material starts oozing out through next nozzles. Remove the grouting connection, close to nozzle. Start injecting through next nozzle. Continue the same process.
  Cleaning: Clean the tools and equipments with clean water immediately after use.
  
  Storage & Shelf Life: Shelf life is six months when stored in original packing at a cool & dry place away from moisture & water.
  
  Packing : 5, 25 hassein polythene lined bags.
  
  Precautions: Do not dilute more than the recommended w/p ratio.

Clients can avail from us Cementitious Grout that is non-shrink, expansive, high early strength, and high workability (flow) general purpose cementitious grout. The Cementitious Grout is made available under the brand name Kemgrout GP. Cementitious Grout (KEMGROUT GP), offered by us, is a nonmetallic, cement based grout with good (workability flow) and positive volumetric expansion. Cementitious Grout is chloride and iron free hence no corrosion & loss of cohesive strength due to corrosion by oxidation particles. The high early strength of cured grouts allows the immediate installation & operation of the machine or equipment. The grout sustains the high dynamic and static loads transfer by the running machine & equipment. The grouting height provision of the grout is 110 - 120 mm.

Benefits

• Non metallic - no cohesion loss due to corrosion.
• Chloride free - no corrosion of steel.
• Good workability and flow-ensure larger contact.
• Non-shrink - duel shrinkage compensation - ensures volume stability.
• High early & ultimate compressive strength.
• Excellent bond between machinery and foundation.
• Nontoxic
• Nonhazardous

End Uses

• Grouting of bolt pockets & base plate of any machine & equipment.
• Boilers, pump sets, generators, turbines, stanchion bases & motors etc.
• Grouting of columns in precast constructions.

Directions For Use


• Surface Preparation:
  The concrete surface including bolt pockets shall be free of oil & greaseThoroughly wire brush the surface to remove dirty & dust. Remove Oil & grease, degreasing with xylene, Toluene or Trichloroethylene solvent. Hack the concrete surface for improvement in bonding.Wash the surface with water till it cleans to a original concrete substrate. Saturate the surface with water prior to grouting.
• Shuttering / Formwork
  Provide wooden or steel leak proof formwork to withstand operational stressers. Seal the gaps of formwork and concrete surface with Kemgrout -gp grout in thick mortat consistency by mixing with less quantity of water. Allow it to cure for 3-4 hours before starting of group pouring / placement.
• Mixing
  Grout mixer or freefall type concrete mixer is recommended.Selection of the grout / concrete mixer capacity will depend on the volume of mixed grout required. The mixer vessel / pot shall be clean & dry. Charge 80% of mixing water. The water must be clean, cold and chloride free. Start the mixer. Start addition of grout powder slowly & continuously for about a minute. Add 25-30 nos. of 5-10 cm size stones or coarse aggregate (clean & dry) for lumpsfree efficient mixing of grout. Add balance 20% of mixing water and mix for 4-5 minutes. Now the grout is ready for pouring / placement.
• Placement / Pouring
  Pour the mixed grout through a 10 cm wire mesh kept on a pouring vessel (200 liter fitted with 2 inch ball value at bottom end of the drum) keep the grout agitating by wooden baffle. make sure that the surface is saturated with water & damp .Excess water if any remove by hand pump or cotton waste. Pour the mixed grout from one side only to avoid air/gap entrapment. Provide 100 mm minimum exposed area (shoulder) of grouts at pouring end and 50 mm on the other end. Cover the grout exposed area by plywood or polyethylene (HDPE) sheet for retrain & evaporation of water.
  Incase grouting bed height exceeds 110 MM, mixing of 50 % by weight of 5 - 10 mm coarse aggregate (clean & dry) is recommended. Provide atleast 10 - 12 hours gap between two subsequent grouting operations.

Grout Quantity Estimation

• Quantity of powder grout required in kgs. = 2.1 - 2.2 x volume of grouting void in liters.
• (Consider about 5% in kgs. wastage and other contingencies while calculating the requirement)

Cleaning Of Tools & Equipments : Easily cleaned with water immediately after the use.

Storage & Shelf Life : Store the material away from moisture, water & cover it by tarpaulin in unopen condition. Shelf life is 6 - 7 months from the date of manufacture

Packing: 30 kg woven sack with a plastic liner.

The concept of latex-hydraulic cement mix design was introduced in the year 1923. But practically, the use of latex modified mortars and concretes started in the 1960s. In almost all developed countries like America, Europe, Japan, and USSR the practical application were started in the 1960s only.Latex - cement combination in cement mortar and concrete is governed by both the cement mortar and concrete is governed by both the cement hydration and latex polymer film formation processes in their binder phase. In the process, a 'co-matrix' phase is formed by both cement hydration & polymer film formation. The properties of ordinary cement mortar and concrete are generally improved to a great extent by latex modification. In latex modified mortar and concrete, it appears that the micro cracks are bridged by the polymer films or membranes which prevent crack propagation and simultaneously, a strong cement hydrate-aggregate bond is formed. The sealing effect due to polymer film formed in the structure also provides a considerable increase in water-proofness, resistance to chloride ion penetration, moisture transmission, carbonation, oxygen diffusion, chemical resistance, and freeze-thaw durability. We offer Polymer Latex Cement Modifier available under the brand name Hydracrete SBR. The Polymer Latex Cement Modifier, offered by us, is especially developed material ensuring quality and durability. Polymer Latex Cement Modifier can be availed at relatively affordable price from us.

Benefits

• Easy to mix & use
• Provides good workability.
• Markedly improved water retention-help in cement hydration.
• Resistance to bleeding and segregation is excellent.
• A noticeable increase in tensile and flexural strength but no improvement in compressive strength.
• The surface hardness of latex modified concrete is improved
• Provides a higher deformation, ductility and elasticity - modulus of elasticity is smaller (0.001-10 x 104 kgf/cm2)
• then the conventional concrete (10 - 30 x 104 kgf/cm²)
• The drying shrinkage may be smaller dependent on latex / cement ratio.
• Latex modified mortar and concrete usually have coefficient of thermal expansion equal to or slightly more than that of conventional concrete.
• Modification reduces water absorption, water permeability, water vapor transmission.
• Improves water-proofness.
• Improved bond strength to various substrates.
• Excellent impact resistance
• Resistant to alkalies but not resistant to inorganic-organic acids and sulfates.
• The chloride ion permeability is low
• Improved resistance to freezing & thawing.

End Uses

• Typical areas of Latex - modified concrete and mortars
• Paving & Flooring : General house flooring, warehouses, office, shops, toilet floors, stairs, passages, chemical plant, railway platforms, roads and garages.
• Water Proofing : Roof decks, block walls, water tank, swimming pool, septic tanks & silos.
• Adhesives (Bonding Agents) : For boning of heat insulating materials, old and new concrete & mortar & repair of cracks.
• Anticorrosive Lining : Effluent drains, chemical factory floors, grouting of acid proof tiles, septic tanks, foundations for machinery plants etc.
• Deck Coverings : Ship decks, bridge decks & footbridge decks.

Application
The mix proportions of latex modifiers concrete & mortars cannot be easily determined unless trials are conducted. By our technical date generation we have found the following suitable mix designs:

Shelf Life : One year from the date of manufacture.

Storage : Store at a cool & dry place, strictly away from sun heat

Packing : 5, 10, 35 liters plastic jars and drum.

The building construction materials are mostly mineral based and they have high porous surface structure which readily absorbs water, the exterior facade get damaged and discolored by rain and atmospheric pollutants. The latest advancement in construction industry is the use of insulating masonry and lightweight blocks and plasters which retains water and moisture. Any absorbed moisture must be able to escape to the atmosphere to protect interiors. To overcome these problems there is need of a coating which must have very high water - vapor permeability, low water absorption, attractive decorative appearance and extreme durability. ACRYSIL the Silicone Resin Emulsion Paint meets all these requirements with mineral like matt finish. The quality Acrysil Silicone Resin Emulsion Paint that we offer is economically priced.

Benefits

• Ready to use
• Brushable, roller and sprayable
• Attractive color shades.
• Excellent water repellency - there is no swelling, flaking or darkening of the finish even after heavy rain and water pressure.
• High permeability to water vapor and carbon dioxide - open pored surface property ensure a controlled water and gas equilibrium. There is also no effect on thermal conductivity or insulation or carbonation.
• Very good resistance to weathering, industrial emissions and microbial attack - the surface remains permanently dry.
• Paintability - because of chalky matt texture, can be easily painted.
• Solvent free - water born excellent environmental compatible.
• No dirt pickup
• No fire hazards.

End Uses
ACRYSIL is an attractive and protective duel function coating that lasts for more than a decade. It is recommended for old as well as newly built residential, municipal, industrial, conservational & repair of historic buildings.

Direction For Use
Surface Preparation
The surface shall be free of dirt, dust and earlier paint. Thoroughly clean the surface. Any repairing of plaster is required must be carried out prior to application of ACRYSIL. No primer is required, because silicone itself bonds strongly to mineral materials. Do not apply on existing oil paints or non - permeable coating like epoxies or polyurethanes. Wash the surface if possible to open the pores for better performance.

Mixing : For priming coat dilute the paint 25 - 30 % by volume with clean water, mix thoroughly to a uniform liquid and apply by good quality brush.

Application : For top coats dilute the paint 15 - 20 % by volume with water and apply by good quality brush or roller. Two coats are required for better hiding and protection.

Cleaning : Tools can be cleaned with water immediately after use.

Storage & Shelf Life : Store the ACRYSIL at cool and dry place away, from sun heat in original sealed containers. Shelf life is six months from the date of manufacture.

Packing : 1, 4, 20 liters plastic or metal tins

We offer Single Pack Silicone that is available under the popular Krisrepell Brand. Single Pack Silicone, offered by us, is water and oil repellent. Single Pack Silicone (KRISREPELL) is available in two grades. One grade is for a treatment of mineral substrates i.e. facades of air faced masonry and cement. Another grade is to improve oil and water resistance of hard stones, marbles, granites etc. Both the materials are ready to use chemically 'SILANE - SILOXANE' composition in a solvent media, forms a chemical structure similar to Quartz on application and reaction.

The Cementitious - mineral building materials when comes in contact with water, pollutant gases and carbon dioxide, they absorb water and results into a damage. The damages are like penetration of moisture, cracks due to swelling & shrinkage, frost & deicing salts, efflorescence and salt damage caused by hydration and crystallization, lime leaching, rust stains, dirt pick up, attack by algae, fungi and moss & chemical corrosion of reinforcement steel yield to destruction of concrete.

Benefits

• Ready to use.
• Can be applied by brush, roller or spray.
• Very thin liquid - deep penetration.
• Drastic reduction in water absorption.
• Resistance to alkalies.
• No change in surface appearance - glossy, tacky or yellowing.
• Resistance to UV light.
• Bridges hairline crack for water repellency.
• Excellent water vapor diffusion.
• Non toxic - no health risk.
• Environmental friendly.
• Stops water seepage & leakage.
• No paint washout - protects paints.
• Prevents corrosion of reinforcement.
• Increases oil, water & stain resistance on absorbent minerals.

End Uses
Protection of following substrates from water in exposed condition cement concrete, mineral plaster and paints, sandstone, sand lime bricks, limestone, marble, granite, brick, jodhpuri and jaipuri stones. KRISREPELL is ideal for water repellency of facades and sloppy roof terrace.

Direction For Use
Surface Preparation
The surface shall be free from oil, grease and dirt. The surface shall be clean and dirt free, otherwise dirt will get dissolved into solvent & will represent dirt stains. If possible wash the surface with clean water after thorough wire brushing. Allow the surface to dry for better penetration. The surface may be slightly damp but not wet.

Application

• Apply two coats of KRISREPELL wet on wet by brush, roller or spray in a flooding way i.e. the material shall
• Run down the substrate while application. The maximum the penetration the best performance it will provide. The performance can be tested only after drying for 24 hours or after 3 days.

Cleaning Of Tools : Clean the tools by white spirit, kerosene or xylene solvent.

Storage & Shelf Life : Shelf life is one year from the date of manufacture. Store the material in cool & dry place away from sun heat.

We are known for making available the quality Concrete Curing Compound. The different varieties of Concrete Curing Compound that we deal in are available under the brand Crete Cure. CRETE CURE W1 & W2 (Concrete Curing Compound) are economical wax emulsion based compound specially formulated to form highly efficient and low cost curing membrane. Concrete Curing Compound dries to a clear and white film which provides effective water retention and a dust free hard surface after application on fresh concrete it retains water, to ensure the strength development of the concrete. The Concrete curing Compound Clear And white being water based and nontoxic, fire hazards are eliminated. Degradation time of the compound membrane depends on weathering and traffic.

Benefits

• Nontoxic, nonhazardous.
• Easy to apply by brush, roller or spray.
• Economical concrete curing with high efficiency.
• Provide harder and dust free concrete surfaces.
• Specially designed for exterior concrete pavements and mass concrte construction.
• Ensures the strength development of the concrete.
• CRETE CURE W2 white provides solar reflective film.
• Degrades after complete curing of the concrete.

End Uses : Dams, Paving, Precast pipes, Exterior mass concretes.

Specific Compliance

• CRETE CURE W1 - ASTM C 309 : 77 Type I, Class A
• CRETE CURE W2 - ASTM C 309 : 77 Type I, Class B

Direction To Use
Application
CRETE CURE are suitable for application under high temperature conditions on exterior concrete pavements & mass concrete constructions but not recommended to use below 5 C Apply by spray or roller or by brush on newly placed concrete (horizontal) surfaces stcots disappearing. On vertical surfaces it is essential that the surface has to be dampened with clean water.

Cleaning : Clean the equipments with water immediately after use.

Packing : 35, 200 Liters plastic drum.

We offer Injection Grout which is a cementitious, high flow, expansive, non-shrink injection Grout. The Injection Grout is made available the popular brand Keminject - K5. Injection Grout (KEMINJECT-K5) is single component cement based expansive grout. Injection Grout is a very fine powder material when mixed with water exhibit flow like water and on curing instead of shrinkage shows positive expansion. The non-shrink characteristic makes it suitable for injection grouting of concrete structures such as buildings, bridges, dams, tunnels etc. On curing for 28 days it equals the strength of M-40 concrete.

Benefits

i>
• Single component, easily miscible with water.
• Very low viscosity after mixing with water helps in penetration of micro cracks of the concrete.
• Bonds strongly to old and new concrete internally.
• Provides 100% filling of cracks and pores.
• Expands on curing by the way of duel shrinkage compensation.
• Strength is much higher than the neat cement paste.
• Not only fills/seals the gaps, cavities and cracks, provides strength to the structure by consolidating it.
• Provides cent percent water proofing after grouting.
• Arrest incoming & outgoing water.
• Color - same as cement.
• Non toxic, non hazardous.

End Uses:

• Injection grouting of Building structures - roof, basement, water tank, swimming pool, toilet, bathroom etc.
• Bridges, dams & tunnels

Direction For Use

Preparation For Injection Grouting
Drill hole on the crack at every one meter in down direction, of the size depends on grouting nozzle size. The depth of the hole shall depend on thickness of the structural part. Clean the dust by air and then by water. Fix the proper size nozzle by using fast setting cement and / or epoxy sealant to cure for at least 24 hours before grouting.
Mixing

• Take clean water as per the w/p ratio into a plastic container (50 liter size).
• Start adding grout powder with continuous stirring to homogenous free-flowing thin slurry.
  Grouting
  Start injecting the mixed slurry by using grouting pump at a pressure of 3-5 kg /cm² till the material starts oozing out through next nozzles. Remove the grouting connection, close to nozzle. Start injecting through next nozzle. Continue the same process.
  Cleaning: Clean the tools and equipments with clean water immediately after use.
  
  Storage & Shelf Life: Shelf life is six months when stored in original packing at a cool & dry place away from moisture & water.
  
  Packing : 5, 25 hassein polythene lined bags.
  
  Precautions: Do not dilute more than the recommended w/p ratio.

Clients can avail from us Cementitious Grout that is non-shrink, expansive, high early strength, and high workability (flow) general purpose cementitious grout. The Cementitious Grout is made available under the brand name Kemgrout GP. Cementitious Grout (KEMGROUT GP), offered by us, is a nonmetallic, cement based grout with good (workability flow) and positive volumetric expansion. Cementitious Grout is chloride and iron free hence no corrosion & loss of cohesive strength due to corrosion by oxidation particles. The high early strength of cured grouts allows the immediate installation & operation of the machine or equipment. The grout sustains the high dynamic and static loads transfer by the running machine & equipment. The grouting height provision of the grout is 110 - 120 mm.

Benefits

• Non metallic - no cohesion loss due to corrosion.
• Chloride free - no corrosion of steel.
• Good workability and flow-ensure larger contact.
• Non-shrink - duel shrinkage compensation - ensures volume stability.
• High early & ultimate compressive strength.
• Excellent bond between machinery and foundation.
• Nontoxic
• Nonhazardous

End Uses

• Grouting of bolt pockets & base plate of any machine & equipment.
• Boilers, pump sets, generators, turbines, stanchion bases & motors etc.
• Grouting of columns in precast constructions.

Directions For Use


• Surface Preparation:
  The concrete surface including bolt pockets shall be free of oil & greaseThoroughly wire brush the surface to remove dirty & dust. Remove Oil & grease, degreasing with xylene, Toluene or Trichloroethylene solvent. Hack the concrete surface for improvement in bonding.Wash the surface with water till it cleans to a original concrete substrate. Saturate the surface with water prior to grouting.
• Shuttering / Formwork
  Provide wooden or steel leak proof formwork to withstand operational stressers. Seal the gaps of formwork and concrete surface with Kemgrout -gp grout in thick mortat consistency by mixing with less quantity of water. Allow it to cure for 3-4 hours before starting of group pouring / placement.
• Mixing
  Grout mixer or freefall type concrete mixer is recommended.Selection of the grout / concrete mixer capacity will depend on the volume of mixed grout required. The mixer vessel / pot shall be clean & dry. Charge 80% of mixing water. The water must be clean, cold and chloride free. Start the mixer. Start addition of grout powder slowly & continuously for about a minute. Add 25-30 nos. of 5-10 cm size stones or coarse aggregate (clean & dry) for lumpsfree efficient mixing of grout. Add balance 20% of mixing water and mix for 4-5 minutes. Now the grout is ready for pouring / placement.
• Placement / Pouring
  Pour the mixed grout through a 10 cm wire mesh kept on a pouring vessel (200 liter fitted with 2 inch ball value at bottom end of the drum) keep the grout agitating by wooden baffle. make sure that the surface is saturated with water & damp .Excess water if any remove by hand pump or cotton waste. Pour the mixed grout from one side only to avoid air/gap entrapment. Provide 100 mm minimum exposed area (shoulder) of grouts at pouring end and 50 mm on the other end. Cover the grout exposed area by plywood or polyethylene (HDPE) sheet for retrain & evaporation of water.
  Incase grouting bed height exceeds 110 MM, mixing of 50 % by weight of 5 - 10 mm coarse aggregate (clean & dry) is recommended. Provide atleast 10 - 12 hours gap between two subsequent grouting operations.

Grout Quantity Estimation

• Quantity of powder grout required in kgs. = 2.1 - 2.2 x volume of grouting void in liters.
• (Consider about 5% in kgs. wastage and other contingencies while calculating the requirement)

Cleaning Of Tools & Equipments : Easily cleaned with water immediately after the use.

Storage & Shelf Life : Store the material away from moisture, water & cover it by tarpaulin in unopen condition. Shelf life is 6 - 7 months from the date of manufacture

Packing: 30 kg woven sack with a plastic liner.

The concept of latex-hydraulic cement mix design was introduced in the year 1923. But practically, the use of latex modified mortars and concretes started in the 1960s. In almost all developed countries like America, Europe, Japan, and USSR the practical application were started in the 1960s only.Latex - cement combination in cement mortar and concrete is governed by both the cement mortar and concrete is governed by both the cement hydration and latex polymer film formation processes in their binder phase. In the process, a 'co-matrix' phase is formed by both cement hydration & polymer film formation. The properties of ordinary cement mortar and concrete are generally improved to a great extent by latex modification. In latex modified mortar and concrete, it appears that the micro cracks are bridged by the polymer films or membranes which prevent crack propagation and simultaneously, a strong cement hydrate-aggregate bond is formed. The sealing effect due to polymer film formed in the structure also provides a considerable increase in water-proofness, resistance to chloride ion penetration, moisture transmission, carbonation, oxygen diffusion, chemical resistance, and freeze-thaw durability. We offer Polymer Latex Cement Modifier available under the brand name Hydracrete SBR. The Polymer Latex Cement Modifier, offered by us, is especially developed material ensuring quality and durability. Polymer Latex Cement Modifier can be availed at relatively affordable price from us.

Benefits

• Easy to mix & use
• Provides good workability.
• Markedly improved water retention-help in cement hydration.
• Resistance to bleeding and segregation is excellent.
• A noticeable increase in tensile and flexural strength but no improvement in compressive strength.
• The surface hardness of latex modified concrete is improved
• Provides a higher deformation, ductility and elasticity - modulus of elasticity is smaller (0.001-10 x 104 kgf/cm2)
• then the conventional concrete (10 - 30 x 104 kgf/cm²)
• The drying shrinkage may be smaller dependent on latex / cement ratio.
• Latex modified mortar and concrete usually have coefficient of thermal expansion equal to or slightly more than that of conventional concrete.
• Modification reduces water absorption, water permeability, water vapor transmission.
• Improves water-proofness.
• Improved bond strength to various substrates.
• Excellent impact resistance
• Resistant to alkalies but not resistant to inorganic-organic acids and sulfates.
• The chloride ion permeability is low
• Improved resistance to freezing & thawing.

End Uses

• Typical areas of Latex - modified concrete and mortars
• Paving & Flooring : General house flooring, warehouses, office, shops, toilet floors, stairs, passages, chemical plant, railway platforms, roads and garages.
• Water Proofing : Roof decks, block walls, water tank, swimming pool, septic tanks & silos.
• Adhesives (Bonding Agents) : For boning of heat insulating materials, old and new concrete & mortar & repair of cracks.
• Anticorrosive Lining : Effluent drains, chemical factory floors, grouting of acid proof tiles, septic tanks, foundations for machinery plants etc.
• Deck Coverings : Ship decks, bridge decks & footbridge decks.

Application
The mix proportions of latex modifiers concrete & mortars cannot be easily determined unless trials are conducted. By our technical date generation we have found the following suitable mix designs:

Shelf Life : One year from the date of manufacture.

Storage : Store at a cool & dry place, strictly away from sun heat

Packing : 5, 10, 35 liters plastic jars and drum.

The building construction materials are mostly mineral based and they have high porous surface structure which readily absorbs water, the exterior facade get damaged and discolored by rain and atmospheric pollutants. The latest advancement in construction industry is the use of insulating masonry and lightweight blocks and plasters which retains water and moisture. Any absorbed moisture must be able to escape to the atmosphere to protect interiors. To overcome these problems there is need of a coating which must have very high water - vapor permeability, low water absorption, attractive decorative appearance and extreme durability. ACRYSIL the Silicone Resin Emulsion Paint meets all these requirements with mineral like matt finish. The quality Acrysil Silicone Resin Emulsion Paint that we offer is economically priced.

Benefits

• Ready to use
• Brushable, roller and sprayable
• Attractive color shades.
• Excellent water repellency - there is no swelling, flaking or darkening of the finish even after heavy rain and water pressure.
• High permeability to water vapor and carbon dioxide - open pored surface property ensure a controlled water and gas equilibrium. There is also no effect on thermal conductivity or insulation or carbonation.
• Very good resistance to weathering, industrial emissions and microbial attack - the surface remains permanently dry.
• Paintability - because of chalky matt texture, can be easily painted.
• Solvent free - water born excellent environmental compatible.
• No dirt pickup
• No fire hazards.

End Uses
ACRYSIL is an attractive and protective duel function coating that lasts for more than a decade. It is recommended for old as well as newly built residential, municipal, industrial, conservational & repair of historic buildings.

Direction For Use
Surface Preparation
The surface shall be free of dirt, dust and earlier paint. Thoroughly clean the surface. Any repairing of plaster is required must be carried out prior to application of ACRYSIL. No primer is required, because silicone itself bonds strongly to mineral materials. Do not apply on existing oil paints or non - permeable coating like epoxies or polyurethanes. Wash the surface if possible to open the pores for better performance.

Mixing : For priming coat dilute the paint 25 - 30 % by volume with clean water, mix thoroughly to a uniform liquid and apply by good quality brush.

Application : For top coats dilute the paint 15 - 20 % by volume with water and apply by good quality brush or roller. Two coats are required for better hiding and protection.

Cleaning : Tools can be cleaned with water immediately after use.

Storage & Shelf Life : Store the ACRYSIL at cool and dry place away, from sun heat in original sealed containers. Shelf life is six months from the date of manufacture.

Packing : 1, 4, 20 liters plastic or metal tins

We offer Single Pack Silicone that is available under the popular Krisrepell Brand. Single Pack Silicone, offered by us, is water and oil repellent. Single Pack Silicone (KRISREPELL) is available in two grades. One grade is for a treatment of mineral substrates i.e. facades of air faced masonry and cement. Another grade is to improve oil and water resistance of hard stones, marbles, granites etc. Both the materials are ready to use chemically 'SILANE - SILOXANE' composition in a solvent media, forms a chemical structure similar to Quartz on application and reaction.

The Cementitious - mineral building materials when comes in contact with water, pollutant gases and carbon dioxide, they absorb water and results into a damage. The damages are like penetration of moisture, cracks due to swelling & shrinkage, frost & deicing salts, efflorescence and salt damage caused by hydration and crystallization, lime leaching, rust stains, dirt pick up, attack by algae, fungi and moss & chemical corrosion of reinforcement steel yield to destruction of concrete.

Benefits

• Ready to use.
• Can be applied by brush, roller or spray.
• Very thin liquid - deep penetration.
• Drastic reduction in water absorption.
• Resistance to alkalies.
• No change in surface appearance - glossy, tacky or yellowing.
• Resistance to UV light.
• Bridges hairline crack for water repellency.
• Excellent water vapor diffusion.
• Non toxic - no health risk.
• Environmental friendly.
• Stops water seepage & leakage.
• No paint washout - protects paints.
• Prevents corrosion of reinforcement.
• Increases oil, water & stain resistance on absorbent minerals.

End Uses
Protection of following substrates from water in exposed condition cement concrete, mineral plaster and paints, sandstone, sand lime bricks, limestone, marble, granite, brick, jodhpuri and jaipuri stones. KRISREPELL is ideal for water repellency of facades and sloppy roof terrace.

Direction For Use
Surface Preparation
The surface shall be free from oil, grease and dirt. The surface shall be clean and dirt free, otherwise dirt will get dissolved into solvent & will represent dirt stains. If possible wash the surface with clean water after thorough wire brushing. Allow the surface to dry for better penetration. The surface may be slightly damp but not wet.

Application

• Apply two coats of KRISREPELL wet on wet by brush, roller or spray in a flooding way i.e. the material shall
• Run down the substrate while application. The maximum the penetration the best performance it will provide. The performance can be tested only after drying for 24 hours or after 3 days.

Cleaning Of Tools : Clean the tools by white spirit, kerosene or xylene solvent.

Storage & Shelf Life : Shelf life is one year from the date of manufacture. Store the material in cool & dry place away from sun heat.

We are known for making available the quality Concrete Curing Compound. The different varieties of Concrete Curing Compound that we deal in are available under the brand Crete Cure. CRETE CURE W1 & W2 (Concrete Curing Compound) are economical wax emulsion based compound specially formulated to form highly efficient and low cost curing membrane. Concrete Curing Compound dries to a clear and white film which provides effective water retention and a dust free hard surface after application on fresh concrete it retains water, to ensure the strength development of the concrete. The Concrete curing Compound Clear And white being water based and nontoxic, fire hazards are eliminated. Degradation time of the compound membrane depends on weathering and traffic.

Benefits

• Nontoxic, nonhazardous.
• Easy to apply by brush, roller or spray.
• Economical concrete curing with high efficiency.
• Provide harder and dust free concrete surfaces.
• Specially designed for exterior concrete pavements and mass concrte construction.
• Ensures the strength development of the concrete.
• CRETE CURE W2 white provides solar reflective film.
• Degrades after complete curing of the concrete.

End Uses : Dams, Paving, Precast pipes, Exterior mass concretes.

Specific Compliance

• CRETE CURE W1 - ASTM C 309 : 77 Type I, Class A
• CRETE CURE W2 - ASTM C 309 : 77 Type I, Class B

Direction To Use
Application
CRETE CURE are suitable for application under high temperature conditions on exterior concrete pavements & mass concrete constructions but not recommended to use below 5 C Apply by spray or roller or by brush on newly placed concrete (horizontal) surfaces stcots disappearing. On vertical surfaces it is essential that the surface has to be dampened with clean water.

Cleaning : Clean the equipments with water immediately after use.

Packing : 35, 200 Liters plastic drum.