Chennai, Tamil Nadu, India
Our Products
FEATURES:
- HIGH SPEED- HIGH SPINDLE TORQUE- BIG SPINDLE BORE- AUTOMATIC FORCED LUBRICATION- HARDENED AND GROUND GUIDEWAYS- BRAND NEW DESIGN EXTERIOR- HEAD STOCKWITH MECHANICAL CLUTCH OR ELECTROMAGNETIC CLUTCH- NO NEED FOR CHANGE GEAR WHEN CUTTING METRIC, INCH, DIAMETRICAL PITCH, MODULE THREAD
| MODEL | CDS6240B | CDS6250B | CDS6256B | CDS6266B | CDS6240C | CDS6250C | CDS6256C | CDS6266C | |
| MAX. SWING OVER BED | MM | 400 | 500 | 560 | 660 | 400 | 500 | 560 | 660 |
| MAX. SWING OVER CARRIAGE | MM | 230 | 290 | 350 | 440 | 230 | 290 | 350 | 440 |
| MAX. SWING OVER GAP | MM | 700 | 760 | 790 | 870 | 700 | 760 | 790 | 870 |
| MAX. LENGTH of WORKPIECE | MM | 1000/1500/2000 | 1000/1500/2000 | 1000/1500/2000 | 1000/1500/2000 | 1000/1500/2000 | 1000/1500/2000 | 1000/1500/2000 | 1000/1500/2000 |
| WIDTH OF GUIDEWAY | MM | 394 | 394 | 394 | 394 | 394 | 394 | 394 | 394 |
| SPINDLE NOSE | D8 | D8 | D8 | D8 | D8 | D8 | D8 | D8 | |
| SPINDLE SPEED | 26-2000 RPM(16 STEPS) | 26-2000 RPM(16 STEPS) | 26-2000 RPM (16 STEPS) | 26-2000 RPM(16 STEPS) | 26-1700RPM(16 STEPS) | 26-1700RPM(16 STEPS) | 26-1700RPM(16 STEPS) | 26-1700RPM(16 STEPS) | |
| DIA. OF SPINDLE BORE | MM | 82 | 82 | 82 | 82 | 105 | 105 | 105 | 105 |
| TAPER OF SPINDLE BORE | 90/1:20 | 90/1:20 | 90/1:20 | 90/1:20 | 110/1:20 | 110/1:20 | 110/1:20 | 110/1:20 | |
| LONGI. FEED | MM//REV | 0.044-1.48 | 0.044-1.48 | 0.044-1.48 | 0.044-1.48 | 0.044-1.48 | 0.044-1.48 | 0.044-1.48 | 0.044-1.48 |
| CROSS FEED | MM//REV | 0.022-0.74 | 0.022-0.74 | 0.022-0.74 | 0.022-0.74 | 0.022-0.74 | 0.022-0.74 | 0.022-0.74 | 0.022-0.74 |
| METRIC THREAD | MM | 0.35-80(53 OR 77) | 0.35-80(53 OR 77) | 0.35-80(53 OR 77) | 0.35-80(53 or 77) | 0.35-80(53 OR 77) | 0.35-80(53 OR 77) | 0.35-80(53 OR 77) | 0.35-80(53 OR 77) |
| WHITWORTH THREAD | 7/16-80 TPI (47) | 7/16-80 TPI (47) | 7/16-80 TPI (47) | 7/16-80 TPI (47) | 7/16-80 TPI (47) | 7/16-80 TPI (47) | 7/16-80 TPI (47) | 7/16-80 TPI (47) | |
| MODULE THREAD | MM | 0.2-40(45 or 66) | 0.2-40(45 OR 66) | 0.2-40(45 OR 66) | 0.2-40(45 or 66) | 0.2-40(45 OR 66) | 0.2-40(45 OR 66) | 0.2-40(45 OR 66) | 0.2-40(45 OR 66) |
| DIA. METRICAL PITCH THREAD | 7/8-160 DP(42) | 7/8-160 DP(42) | 7/8-160 DP(42) | 7/8-160 DP(42) | 7/8-160 DP(42) | 7/8-160 DP(42) | 7/8-160 DP(42) | 7/8-160 DP(42) | |
| MAX. TRAVEL oF Cross SLIDE | MM | 348 | 348 | 348 | 355 | 348 | 348 | 348 | 355 |
| MAX. TRAVEL OF TOP SLIDE | MM | 150 | 150 | 150 | 150 | 150 | 150 | 150 | 150 |
| TRAVEL OF TAIL -STOCK QUILL | MM | 150 | 150 | 150 | 150 | 150 | 150 | 150 | 150 |
| DIA OF TAILSTOCK | MM | 75 | 75 | 75 | 75 | 75 | 75 | 75 | 75 |
| TAPER BORE OF TAIL STOCK QUILL | M5 | M5 | M5 | M5 | M5 | M5 | M5 | M5 | |
| MAIN MOTOR | HP | 10/15(OPTIO | 10/15(OPTIO) | 10/15(OPTIO) | 10/15(OPTIO | 10/15(OPTIO) | 10/15(OPTIO) | 10/15(OPTIO) | 10/15(OPTIO) |
FEATURES:- EXTRA HEAW DUTY LATHE WITH GAP BED MOTORISED MODEL S.S.& S.C. SPEED GEAR BOX TYPE- MAIN SPINDLE MADE OUT FROM BEST STEEL & RUNNING WITH CONICAL BRASS TYPE BEARINGS,
| FOR HEIGHT OF CENTRE 24" (600 MM) | ||||||||
| LENGTH OF BED | 14' | 16' | 18' | 20' | 22' | 24' | 26' | 30' |
| CENTER HEIGHT | 24" | 24" | 24" | 24" | 24" | 24" | 24" | 24" |
| WIDTH OF BED | 28" | 28" | 28" | 28" | 28" | 28" | 28" | 28" |
| SPINDLE HOLE | 41/8" | 4 1/8" | 4 1/8" | 4 1/8" | 4 1/8" | 4 1/8" | 4 1/8" | 4 1/8" |
| SWING IN GAP | 72" | 72" | 72" | 72" | 72" | 72" | 72" | 72" |
| SWING OVER BED | 48" | 48" | 48" | 48" | 48" | 48" | 48" | 48" |
| SWING OVER SLIDE | 36" | 36" | 36" | 36" | 36" | 36" | 36" | 36" |
| SPINDLE RPM | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 |
| WIDTH OF GAP IN FRONT OF FACE PLATE | 20" | 20" | 20" | 20" | 20" | 20" | 20" | 20" |
| ADMIT BETWEEN CENTERS | 7' | 9' | 11' | 13' | 15' F38 | 17' | 19' | 23' |
| LEAD SCREW DIA/PITCH x TPI | 21/2''X2TPI | 21/2''X2TPI | 2 1/2''X2TPI | 2 1/2''X2TPI 2 1/2" X 2 | 2 1/2" X 2 | 2 1/2" X 2 | 21/2" X 2 | |
| FACE PLATE | 4' | 4' | 4' | 4' | 4' | 4' | 4' | 4' |
| HP REQUIRED | 10 | 10 | 10 | 10 | 15 | 15 | 15 | 15 |
| FOR HEIGHT OF CENTRE 32" (800 MM) | ||||||||
| LENGTH OF BED | 14' | 16' | 18' | 20' | 22' | 24' | 26' | 30' |
| CENTER HEIGHT | 32" | 32" | 32" | 32" | 32" | 32" | 32" | 32" |
| WIDTH OF BED | 36" | 36" | 36" | 36" | 36" | 36" | 36" | 36" |
| SPINDLE HOLE | 45/8" | 4 5/8" | 4 5/8" | 4 5/8" | 4 5/8" | 4 5/8" | 4 5/8" | 4 5/8" |
| SWING IN GAP | 88" | 88" | 88" | 88" | 88" | 88" | 88" | 88" |
| SWING OVER BED | 64" | 64" | 64" | 64" | 64" | 64" | 64" | 64" |
| SWING OVER SLIDE | 52" | 52" | 52" | 52" | 52" | 52" | 52" | 52" |
| SPINDLE RPM | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 |
| WIDTH OF GAP IN FRONT OF FACE PLATE | 20" | 20" | 20" | 20" | 20" | 20" | 20" | 20" |
| ADMIT BETWEEN CENTERS | 7' | 9' | 11' | 13' | 15' | 17' | 19' | 23' |
| LEAD SCREW DIA/PITCH x TPI | 2V2' x 2 | 2V2' X 2 | 2%' x 2 | 2V2' X 2 | 2V2' X 2 | 2V2' X 2 | 21/2' X 2 | 21/2'x2 |
| FACE PLATE | 5' | 5' | 5' | 5' | 5' | 5' | 5' | 5' |
| HP REQUIRED | 10 | 10 | 10 | 15 | 15 | 15 | 15 | 15 |
| FOR HEIGHT OF CENTRE 36" (900 MM) | ||||||||
| LENGTH OF BED | 14' | 16' | 18' | 20' | 22' | 24' | 26' | 30' |
| CENTER HEIGHT | 36" | 36" | 36" | 36" | 36" | 36" | 36" | 36" |
| WIDTH OF BED | 42" | 42" | 42" | 42" | 42" | 42" | 42" | 42" |
| SPINDLE HOLE | 45/8" | 45/8" | 45/8" | 4 5/8" | 4 5/8" | 4 5/8" | 4 5/8" | 4 5/8" |
| SWING IN GAP | 96" | 96" | 96" | 96" | 96" | 96" | 96" | 96" |
| SWING OVER BED | 72" | 72" | 72" | 72" | 72" | 72" | 72" | 72" |
| SWING OVER SLIDE | 58" | 58" | 58" | 58" | 58" | 58" | 58" | 58" |
| SPINDLE RPM | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 |
| WIDTH OF GAP IN FRONT OF FACE PLATE | 20" | 20" | 20" | 20" | 20" | 20" | 20" | 20" |
| ADMIT BETWEEN CENTERS | 6' | 8' | la' | 12' | 14' | 16' | 18' | 22' |
| LEAD SCREW DIA/PITCH x TPI | 21/2' X 2 | 21/2' X 2 | 21/2' X 2 | 2112' X 2 | 21/2' X 2 | 2V2' X 2 | 2V2' X 2 | 21/2' X 2 |
| FACE PLATE | 6' | 6' | 6' | 6' | 6' | 6' | 6' | 6' |
| HP REQUIRED | 15 | 15 | 15 | 15 | 20 | 20 | 20 | 20 |
FEATURES :- CNC Slant Bed Bench Turning Centre - 8 Station Indexing Tool Post - SIEMENS 802D SOLUTION LINE control / FANUC Oi Mate Programming and Industrial type Control Panel with 10" colour monitor with closed loop servo motor control with further option of linking to CAD/CAM and FMS (Flexible Manufacturing System).
FEATURES:Fanuc Oi Mate-MD CNC Control
