Maneklal and Sons (Exports)

Nariman Point, Mumbai, Maharashtra

Hexagonal Wire Netting Machine has a circular pinion holder on the front and rear of the machine. The wires fed from the bobbins and the spiral coils (prepared in spiral coiling machine) placed on the front and rear rack of the machine produces the netting. The net is pulled out by the take-up roller with stands on the surface of the machine and wound automatically on the winding roller. When the required length of netting is produced, the net is cut and removed from the roller manually.

Suitable for extracting oil from Groundnut Kernels, Sesame, Sunflower, Mustard, Rap seed, Caster seed, Cotton Seed, Soya Seed, Corn Germ, Coconut, etc.In place of Decorticator, a suitable nut cracker (for Palm nut), Coconut Cutter (for Coconut), etc. is provided.Mill is suitable for extraction of Edible Non-Edible Oil, From 100 Kgs. of good quality oil seeds, approximately the following quantity of oil can be extracted: Groundnut Kernels and Sesame - 45 Kgs., Sunflower - 35 Kgs., Mustard and Rap seed - 36 Kgs., Caster seed - 40 Kgs., Cotton Seed - 16 Kgs., Soya Seed - 15 Kgs., Corn Germ - 43 Kgs.From 100 Kgs. of Coconut (Dried) 63 Kgs. of Oil can be extracted, Available in 4, 8 and 15 Ton Crushing Capacity per 24 hours.

Machines comprise of six ten work rolls arranged in pairs, Rolls quickly and easily adjustable angularly to give perfect contact between the tube and the roll, over the maximum effective roll profile, - Simple setting of the machine for different sizes of tubes, All rolls driven by two identical electric motors, Machines fitted with indicators for vertical and angular setting of rolls, Machines available in Single Speed and Variable Speed Options.

One 0.50 HP 2800 RPM motor, RF switch, Machine Lamp, Bangle Inside Turning Attachment, Bangle Outside Turning Attachment, Ring Inside Turning Attachment, Ring Outside Turning Attachment, set of 25 nylon collets for Bangle Inside Turning in size 2" to 2.75", set of 13 nylon collets for Bangle Outside Turning in size 2" to 2.75", set of 10 nylon collets for Ring Inside Turning, set of 10 nylon collets for Ring Outside Turning. Diamond Tools for Ring Inside Turning, Diamond Tools for Bangle Inside and Outside Turning and Ring Outside Turning.

Incorporates Rotary Rinsing - Rotary Gravi Filling and Rotary Screw-on Capping operations on a single base, Rinsing device uses neck grippers to invert the bottles for Rinsing and automatically unloads into the inlet turret of the Gravi Filling section in the upright position after Rinsing internally, Bottles once located in the Rinsing Station are released only after all the three operations (Rinsing - Filling - Capping) are over, Adequate neck holders provided at the Filling and Capping Stations to eliminate buckling of Pet Bottles, Universal Hopper provided for automatic Capping provided diameter of the caps is larger then its height, No bottle - No Rinse. No bottle - No Fill, No bottle - No Cap. Available in two models: RFC-L (with 16 jets Rinsing + 16 heads Filling + 8 heads Capping combinations) and RFC-S (with 8 jets Rinsing + 6 heads Filling + 6 heads Capping combinations), Can be adapted to Rinse, Fill and Cap bottles from 200 ml upto 2000 ml in a single stroke. Approximate output speeds of 24 bpm and 60 bpm for 1 litre Mineral Water Bottles on the above two models possible. Can also accommodate other sizes of bottles with the help of change parts on request.Can also be adapted for other applications like juices, squashes, etc. in Pet Glass bottles. Outputs will depend on volume of fill and type characteristics of liquid to be filled.

International and ISI Standards for Machine Testing followed. Castings properly seasoned for providing consistent accuracy during the entire life of the machine. Wheel Head, Work Head and Tail Stock Spindles made of Special Steel, Hardened and Ground for Precision Grinding and a Long Life. Good Quality Angular Bearings provided in the Wheel Head, Work Head and Tail Stock. Gears made of Alloy Steel and are Hob Cut. Automatic Lubrication System provided in the Wheel Head Assembly for longer life of the Phosphorus Bronze Bushes and Spindle. Taper Table helps in easy flow of Cutting Oil.

Pump and Gallery Leakage Testing, Checking Coupling Timing Mark, Phasing the Pump, Calibrating (Flow Testing) the output of each element of the pump, Setting the Pump for Maximum Output, Complete Cut-off, Checking of Governor and Feed Pump Testing.

Semi-Automatic Press, Complete steel body, Push Button type Pressure System, HTP-50 of capacity 50 Tons for making tiles up to 300 x 300 mm with 3 HP Motor, HTP-80 of capacity 80 Tons for making tiles up to 500 x 500 mm with 5 HP Motor, Production: 1000 to 1200 tiles of 250 x 250 mm in 8 hours shift.

The main machine has two rubber rolls rotating in opposite direction at different speeds. Paddy is husked between these rolls. A blower fan separates brown rice from husk. The brown rice is then passed to the polishing chamber. This chamber has a specially designed hollow polishing roller with screen casing. Brown rice is polished by frictional action among the grains. Air is injected through the roller, which helps in the removal of bran and in the cooling of the grain. An aspirator and a cyclone arrangement is also provided for collection of rice bran. Polished rice is taken on a small screen to separate broken particles.

Suitable for precision forging for the Automobile, Railways, Defense, Aeronautics, Hand Tools, Agricultural, Bicycle and other engineering industries.ANVIL BLOCK: Made of Grey Cast Iron weighing approximately 20 times the nominal capacity of the hammer. It is machined on both the top and bottom faces to hold die holder firmly and maintain position of the columns. Die holder fixed in the anvil block is forged from high grade alloy steel hardened and positioned properly with alloy steel tapered wedge.COLUMNS, SLIDES and TUP: Cast Steel columns, duly annealed and machined, positioned by a large spigot on the underside of each foot which fits into a machined recess in the anvil block. Columns locked with tapered wedges of alloy steel to ensure firm alignment of columns which helps in accurate grinding of tup (made of EN-9 cast steel). The clearance between the tup and guideways attached to columns maintained with the help of tapered wedge which brings the columns inward and the drawback bolt provided which pushes the columns outwards. Synthetic rubber mat provided on anvil block on which the columns rest. This dampens the induced shock vibrations, which increases the life of the tup and columns and also ensures smooth working of the machine for longer period.

Electric Motor, Control Panel, Wire Coil Stand, Die for making any one size of Handle, Guard for Flywheel (guard shown on photographs is optional accessory), Additional Dies for other sizes of Handles.

Abrasive Belt Grinders supplied with Abrasive Belts, Serrated Rubber Wheel, Belt Guard, Rotary Switch Starter (Also Grinding Wheel or Taper Spindle and Eye Shield in Combination Models). Lathe Mounting Models are available with other centre heights as per customers requirement.

NB brand calendar rimming machine is most useful and suitable machine for every kind of calendar manufactures. Can fix calendar rim in double fold easily. Various types of calendar rimms attached with plastic tags or without tags are readily available in the market. These rimms have a 45 degree bend lengthwise of the rim. One leg is small while the other leg is almost double. The printed calendar papers are inserted manually in the prefolded rim which has already been placed in the machine as shown in the figure. Then with the handle of the machine, it is rotated about 180 degree. This is called first stroke with this stroke, the calendar papers are held firmly by the rim because when we make the first stroke the smaller leg gets pressed & the longer leg gets a new bend & at the same time gets flattened. Then again we make another stroke only for more pressing the already pressed rims to make it a rigid one. At the time of first stroke a thread loop can be placed along with the papers for hanging the calendar on the wall. The purpose of the calendar rimming machine is to make a bend of 45 degree on the rim (IF it in not present already) Press the 45 degree smaller leg & at the same time make a fold in the longer leg of the rim from center & press it to overlap the previous fold. Then again pressing with second stroke.

Standard Accessories: Electric Motor, Starter, Wire Stand and a set of dies and cutters for any one size, Material: Aluminium, Mild Steel, Brass, Copper, Production per minute: 80 to 85 Rivets.Length of Rivet: 5 to 10 mm, 2 to 4 mm, 3 to 6 mm.

By employing Metal Gathering, many of the well known technical limitations and disadvantages of Mechanical Upsetting can be overcome, Simultaneous heating and forming in one machine, Almost unlimited gather in one operation. The mechanical upsetting limitation of about three times the diameter no longer applies. The modern engine valve has an upset length of up to 20 times diameter and lengths up to 40 times diameter are commonly electro-upset, No longitudinal flash is formed (of the kind which is unavoidable in Mechanical Upsetter), No waste of Heating Energy or Material. Outside of the upset volume can be precisely controlled to allow subsequent 'Flash-Less' forging in closed dies, Always ready for Instant Use. No warm-up period. Energy efficient, about 0.35 to 0.40 kwh kg. Minimal scaling because of simultaneous heating and gathering. Improved die life in subsequent forging operations. Noise Free and Environment Friendly as the machine does not emit heat, fume, exhaust gases or other pollutants. Free upsets can be finish forged without re-heating thus saving time and energy. Consistent heating temperature through the use of thyristor control.Optimal grain flow and fault free surface. The unheated bar length remains unchanged.

- A rotating drum with slots which separate the punch caps from scrap ring - Power: 0.5 HP motor - Net Weight: approx. 200 kgs. - Dimensions: 0.65 x 1.25 x 0.70 m.

Horizontal and Vertical Straightening Device, Clamping Device for adjusting pressure of feeding rollers, Clamping device for Coiling Mandrel, retractable mandrel, Brake arrangement for Feeding Rollers, Piece Counter, Electric Control Panel and electricals, complete set of tools to cover entire wire diameter range of the machine.

Standard Accessories: Electric Motor, Starter, Head and Stem Forming Dies and Cutter Set for one size of nails, Size of Nail Manufactured (Length) No. 2 (1.5"), No. 3 (1.75"), No. 4 (2") & No. 5 (2.15"), No. 2 (1.5"), No. 3 (1.75"), No. 4 (2"), No. 5 (2.15"), No. 6 (2.35") & No. 7 (2.5").

Planetary action with three speeds - 38, 128 and 170 RPM for perfect mixing. The agitator rotates on its axis in the opposite direction to the bowl. This lets the agitator reach every part of the batch for the most uniform mixing, thoroughly blending and aerating all the ingredients , Mixers supplied with a Stainless Steel bowl, Flat Beater and Wire Whip. A Dough Hook and a Bowl Truck can be supplied optionally at extra cost, All contact parts are made from Stainless Steel 304.

- Thresher runs on a Diesel Engine

- Husk does not break into small pieces. Full length husk comes out of the blower

- Full length husk can be used as packing material for glass articles and this is in great demand

- Drum is closed type with thick gauge of sheet and clamp with a detachable flat system

The sheet is fed to the machine by means of a Roller System Mechanism. The die is preloaded on the machine. On feeding the sheet, the upper section of the machine starts stroking. The sheet is perforated as per the die and is advanced by the amount of the perforated pitch set on the machine, with the next stroke of the slide. This cycle of feeding and perforating continues automatically.

- Designed to slice cakes, breads, rusks, etc. including delicate products or soft and sticky products- All contact parts are chrome plated- PVC coated endless conveyor belt for hygienic operation- The crank drive rotates in a strong and totally enclosed casing containing lubricating oil- Knives holders of high quality cast aluminium- Additional knife holders can be provided with different slice thickness. Easy replacement of frames holding the knives.- All rotating parts on ball bearings to reduce wear and tear

- Machine can produce plain fine-mesh wire netting fabric

- Available in various types depending on the size of the mesh and the wire gauge

- The wire material can be Galvanized Iron, Black Iron, Brass, Copper, Stainless Steel, Silver, Platinum, etc.

- Welding Transformers available for Single Phase and Two Phase connection as required- Available in both Air Cooled as well as Oil Cooled versions- Stepless Variation in Current helps in adjusting suitable current for wide range of jobs- Suitable for indoor as well as outdoor work.

2 nos. fabricated with M.S. Pipe, shaft & flat Bar Rod, 2 nos. fabricated with M.S. pipe and shaft4 nos. fabricated with M.S. Plate, 1 no. fabricated with M.S. angle, plate, wheels, 8 nos. cast iron block with phosphor bronze liner

BUCKET ELEVATOR: Heavy Duty 21 Feet High to carry raw feed from Hammer Mill to Batch Bin above the Mixer with 3 HP electric motor

HORIZONTAL FEED MIXER: The horizontal mixers are most suitable for processing animal feeds i.e. for Poultry, Cattle, Pigs, Sheep and Aqua Feeds. These mixers are a versatile machine and produce a homogenous mix of ingredients. Molasses, liquids, fats, etc. can be directly added.

Features and Specifications of the Mixer:- Unique tumbling action gives good uniform and homogenous mixing- Slow moving 'Soft Mix' action eliminates product damage and degradation- Within a matter of five minutes an excellent and homogenous mix is prepared- Size: 50 Cubic Feet and 100 Cubic Feet- Capacity: 2 MT per Hour OR 4 MT per Hour- Electric Motor: 15 HP or 20 HP

Standard Accessories: One 0.50 HP / 2800 RPM motor, R/F switch, Machine Lamp, Bangle Inside Turning Attachment, Bangle Outside Turning Attachment, Ring Inside Turning Attachment, Ring Outside Turning Attachment, set of 25 nylon collets for Bangle Inside Turning in size 2" to 2.75", set of 13 nylon collets for Bangle Outside Turning in size 2" to 2.75", set of 10 nylon collets for Ring Inside Turning, set of 10 nylon collets for Ring Outside Turning. Optional Accessories: Diamond Tools for Ring Inside Turning, Diamond Tools for Bangle Inside and Outside Turning and Ring Outside Turning

- The Bar Drawing Machines are suitable for drawing round bars, sectional bars, re-bars, ribbed bars, reinforcement bars, tubes, etc.- Machine supplied with Single Rod Holding Device, Gearbox, Bull Gear, Pinion Gear and Chain Link

- After hot cambering on the cambering press, the hot leaves are pushed into quinching oil tank and are cooled down on conveyors to room temperature. These leaves are then cooled in open air to give required hardness to the leaves- With Oil Cooling Tower arrangement- Electric Motors: 1 HP motor for circulating of quinching oil and 3 HP motor for movement of conveyor through reduction gear box.- Supplied with quinching oil storage tank of capacity 8000 to 10000 liters- Quinching oil is used for hardening of the leaf spring

- The machine comes with a reduction 4 HUD gearbox, 3 HP / 1440 RPM Motor. There are 4 sprocket wheels, which guide the chain and slats.- The quenching oil tank is fitted with an electronic temperature gauge or temperature of oil. It is also fitted with an alarm which will sound if the temperature crosses 80^o C or as preset on the thermocouple. The flash point of the quenching oil is 130^o C hence, to avoid fire, it is essential that the temperature is maintained below 100^o C. The optimum temperature for getting good results for hardening is 60^o C to 70^o C

- Designed to slice different types of Breads, Rusks, Cakes, etc.- Output of around 600 loaves of 400 gms per hour- Suitable frames can be provided to suit your preferred slice thickness-The loaves of bread / rusks are to be placed one behind the other on the gravity feeding tray. They are sliced without wastage. The vertical running knives slice the loves at equal thickness as per requirement.- All steel welded construction- Grease packed heavy duty ball and roller bearings for smooth operation- Knives individually mounted under balanced tension- Frames giving different slice thickness can be fitted- All contact parts are chrome plated

2 nos. fabricated with M.S. Pipe, shaft & flat Bar RodFinish Roll 2 nos. fabricated with M.S. pipe and shaftRoll stand 4 nos. fabricated with M.S. PlateMoving table 1 no. fabricated with M.S. angle, plate, wheelsTie Rod 3 nos.Bearing block 8 nos. cast iron block with phosphor bronze linerUp Down Roll adjustment system 2 setsBase frame fabricated with M.S. channel and plateFoundation bolt 10 nos.Drive Ac motor with reducer gear train gear boxElectrical Panel 1 no.

- The required (cold to 250 degrees centigrade) temperature is attained in 25 to 30 minutes- When the oven reaches its baking temperature, simply open the door and push the rack into the baking chamber. The rack will automatically stop at its correct position- A signal informs you that the baking cycle is over- Heat Exchanger: An oil or or Gas burner produces the energy in a heat exchanger. A fan circulates the air around in the heat exchanger and into the baking chamber. This hot air bakes the products. The hot air is re-circulated to the heat exchanger.- The front of the oven is made of Stainless Steel 304- Simple to read and easy to use Control Panel provided in conformity with the safety standards- 24 hours continuous working capacity-Smokeless and soundless. It can also be installed in residential areas or/and at higher floors- Full view glass door- Automatic greasing system- Fitted with self cleaning system. Indicator to show whether the tank is empty or full- Suitable for bakeries, hotels as well as fast food joints- Can be provided to operate on three phase or single phase supply voltage

Being the reckoned names in the industry, we offer an extensive range of Compound Sliding Tables that are dimensionally accurate in nature and can be adjusted as per the requirement of our clients. We offer them in varied dimensions and strength and can be adjusted as per the requirement of our clients. We offer them in different grades and dimensions and are highly durable in nature. Moreover, we offer them at most affordable rates.

- Automatic Feed Attachment provided to the Press to feed aluminium strips onto the die and for ejection- Two pairs of feed rolls push and pull the strip on the die automatically

Designed to slice different types of Breads, Rusks, Cakes, etc.The loaves of bread rusks are to be placed one behind the other on the gravity feeding tray. They are sliced without wastage. The vertical running knives slice the loves at equal thickness as per requirement.Frames giving different slice thickness can be fitted.

- A very compact and Sturdy Rice Mill. A 400 square feet floor space is sufficient for running the plant conveniently- High Operating Efficiency- Completely Automatic Process- Just 2 to 3 persons can operate the plant in a dust free, clean working environment- Polishing done without any Abrasive Cone and Rubber Parts, thereby saving on the operating cost and breakdowns of the plant- Excellent milling gives a beautiful glossy finish to rice- High and uniform husking ratio due to specially designed gearbox- Arrangement for complete Bran collection- Four Main Operations: PreCleaning - Shelling (De-husking) - Polishing (Milling) - Grading.

 

Paddy Cleaner: This unit has an oscillating Screen and a Centrifugal Blower. All impurities like stones, paddy stalks, dust, dead paddy, etc. are effectively separated. The clean paddy is then conveyed to the main machine through a bucket elevator.

Main Machine: The main machine has two rubber rolls rotating in opposite direction at different speeds. Paddy is husked between these rolls. A blower fan separates brown rice from husk. The brown rice is then passed to the polishing chamber. This chamber has a specially designed hollow polishing roller with screen casing. Brown rice is polished by frictional action among the grains.Air is injected through the roller, which helps in the removal of bran and in the cooling of the grain. An aspirator and a cyclone arrangement is also provided for collection of rice bran.Polished rice is taken on a small screen to separate broken particles

Standard Accessories: Motors, Paddy Cleaner, 2 Bucket Elevators, Mini Rice Mill & Grader

Optional Spares: Polishing Screen, Polishing Screw, Rubber Roller

- The water metering unit measures the right quantity of water for dough making- The supply of water is as prescribed in the recipe norms the andthis ensures uniform product quality- The 65 Liters capacity Water Measuring Unit measures the water to the required quantity for perfect mixing- Water Batching Tank is recomended for kneading best quality dough- The stainless steel tank with double jackets is injected with puff insulation.- An 'empty' and 'full' indicator for water level is provided- Any liquid item can be measured in the measuring unit- The float in the water level gauge indicated the water level on the scale- Machine is provided with electronic control panel and dial temperature meter with built-in safety devices- Water container has a litre scale and a dial temperature meter- Stainless steel valves and solenoid valves provided for water inlet / outlet

- Cast Iron box section rigid body- Lower spindle horizontally adjustable- Upper spindle vertically adjustable and spring loaded- Available as hand operated model for bench mounting & motorized model with floor stand.

- For production of tablets in various shapes and sizes- Application in Pharmaceuticals, cosmetics, food products, plastics, metallurgy, chemicals and pesticides- 'JM' & 'JS' series models are Single Sided available in Standard and GMP* type- 'JD' series models are Double Sided available in Standard and GMP type- 'DH' series models are Double Sided available in GMP type only- Pre Compression Option and Bi Layer Tablet Option available on the 'JD' and 'DH' series models

Dies for Pilfer Proof Caps, Aluminium Seal, Screw Caps, Cap Liner, Pull-Off Caps, Roll-On Caps, Lug Caps, Shoe Polish Caps, etc.- Single Cavity to Five Cavity Dies- All Die parts made from special quality die steel, hardened and ground finished for longer life- Pillar set made from E.N. Steel duly stress relieved and hand scrapped- Die designed to Cut, Draw and Trim in a single operation

- Themachine can be sued for all types of dough and is fitted with two standard dividing pistons- The dough hopper can be fitted manually or with lifting / tilting device depending on the production required- The machine can be used either for manual removal of dough pieces or in the semi-automatic bread plant- The divider works on rotating drum principal. The measuring pistons move in rotating drums.- Dough pieces are ejected by gravitational force- The amount of dough conveyed can be adjusted to the required weight to the required weight by means of handwheel- The dough reaches the dividing chamber from the hopper. After the chamber has been closed by the knife, the dough is conveyed into the measuring chamber by the main piston- The volume of this measuring chamber corresponds to the set dough weight- After the rotating drum has turned 90 degrees, the dough piece is pushed out by measuring piston. As the rotating drum moves back, the dough piece is scraped off and drops onto the discharge conveyor.- Two pocket dividing unit producing two pieces of dough- Hand wheel for adjustment of weight volume- Hand wheel for the production speed adjustment (minimum / maximum) cuttings/ minute- Stainless steel hopper with 80 kgs. dough capacity

Standard Accessories: Spindle BS-65 (Boring Capacity Diameter 65 - 135 mm), Boring Tool Setting Device complete with micrometer, Two tool holders for boring, Portable Grinder with suitable Grinding Lapping wheels, Two sets of parallel blocks of sizes 200 x 600 mm and 120 x 600 mm, Service spanners, Optional Accessories: Spindle BS-46 (Boring Capacity Diameter 46 - 70 mm), Spindle BS-130 (Boring Capacity Diameter 130 - 230 mm), V Block Stand for V Type Engines, AC Drive instead of Mechanical Machine.

Loading of Paper Strip Rolls, Application of Adhesive, Pasting Through Rollers, In-Line Cutting at Desired Length, Optional - Cutting V slots on Angle Board. After pre-forming, the papers are fed into forming machine which has three stations with big angular female and male rollers operated pneumatically. As the paper is fed through the machine, the angle is formed stage by stage and then it is passed to the shearing system. Rollers are driven by motors with speed control.

- Effective and Continuous Grinding- Suitable for Wet-Pulpy and Dry Grinding- Compact Size- Dust Free operation. No wastage of product and no pollution hazards- The Mini Pulveriser grinds almost all Spices, green chilies, fresh ginger, garlic, salt, sugar, coffee, fresh fruits, fruit pulp, vegetables, tobacco, herbs, beetle nuts, herbs, roots, leaves, bark of trees, oil cake, cattle and poultry feeds, icing sugar, custard powder, instant food, food colours and allied food product.

 

 

Standard Accessories: Electric Motor, Starter, ‘V’ belt fittings and a set of spares

 

Filter Screens: A set of perforated round hole screens are supplied with the machine in sizes: 1/64", 1/32", 1/16", 1/8", 3/8". These sizes will cover fine grinding of sugar, medium grinding of chilly and also coarse grinding of wet-Pulpy material and granular grinding

 

Operation: The flow of material from the Feeding Hopper is regulated by means of a Vertical Adjustable Slide to suit the load indicated by the ammeter. Rotor with four beaters runs in anti-clockwise direction. The swinging beaters pass just beneath the Ratchet Teeth Liner fitted inside the top half of the grinding chamber, leaving a gap of 1/16" between the liner teeth and the tips of the rotating beaters. This cuts the material caught between the liner teeth like a sword with a scissors action at a high speed of 4500 to 6000 RPM. After the required size reduction, the material will pass through the screen fitted inside the lower discharge end of the grinding chamber. No sieving is required, as the appropriate size screen fitted will not allow coarser material to pass through. The air generated in the grinding chamber forces the powder to pass through the screen fitted at the bottom discharge end of the grinding chamber, into a cotton bag attached to the delivery trough below. The dust is collected through the attached balloon fitted on the discharge end. The top closed end of the balloon may be suspended from the roof or a wall of the building. Every half an hour the balloon should be tapped to knock down the dust clogging the pores of the balloon, thus releasing the pressure built-up. The dust falls in the bag below, and thus a dust free operation without wastage of product can be achieved. (When Grinding Wet-Pulpy materials, the balloon should not be used)

Servicing Guidelines: Lifting up the handle opens the cover of the grinding chamber. The grinding parts can be cleaned with a brush within a couple of minutes and the machine is ready for the next batch of grinding. If required, the grinding chamber can also be washed with water. Remove the cotton bag and the screen, close the cover tightly and start the grinder. Now pour a bucket or two of water into the hopper. The grinding parts will be flushed with the water and cleaned. Continue running the machine for a few more minutes as the draft of the fresh air sucked into the grinder will dry it.The beaters, when worn out, can be removed and reversed by unscrewing the two allen-screws holding the outside rotor plate. When both the edges are worn out, they can be sharpened on an emery stone and reused as new. When completely worn out, the tips can be re-welded in Manganese Steel, Ground to Size for equal weight and refitted.

 

- Effective and Continuous Grinding- Suitable for Wet-Pulpy and Dry Grinding - Compact Size- Dust Free operation. No wastage of product and no pollution hazards- The Mini Pulveriser grinds almost all Spices, green chilies, fresh ginger, garlic, salt, sugar, coffee, fresh fruits, fruit pulp, vegetables, tobacco, herbs, beetle nuts, herbs, roots, leaves, bark of trees, oil cake, cattle and poultry feeds, icing sugar, custard powder, instant food, food colours and allied food products.

 

 

 

Filter Screens: A set of perforated round hole screens are supplied with the machine in sizes: 1/64", 1/32", 1/16", 1/8", 3/8". These sizes will cover fine grinding of sugar, medium grinding of chilies and also coarse grinding of wet-Pulpy material and granular grinding

Operation: The flow of material from the Feeding Hopper is regulated by means of a Vertical Adjustable Slide to suit the load indicated by the ammeter. Rotor with four beaters runs in anti-clockwise direction. The swinging beaters pass just beneath the Ratchet Teeth Liner fitted inside the top half of the grinding chamber, leaving a gap of 1/16" between the liner teeth and the tips of the rotating beaters. This cuts the material caught between the liner teeth like a sword with a scissors action at a high speed of 4500 to 6000 RPM. After the required size reduction, the material will pass through the screen fitted inside the lower discharge end of the grinding chamber. No sieving is required, as the appropriate size screen fitted will not allow coarser material to pass through. The air generated in the grinding chamber forces the powder to pass through the screen fitted at the bottom discharge end of the grinding chamber, into a cotton bag attached to the delivery trough below. The dust is collected through the attached balloon fitted on the discharge end. The top closed end of the balloon may be suspended from the roof or a wall of the building. Every half an hour the balloon should be tapped to knock down the dust clogging the pores of the balloon, thus releasing the pressure built-up. The dust falls in the bag below, and thus a dust free operation without wastage of product can be achieved. (When Grinding Wet-Pulpy materials, the balloon should not be used)

Servicing Guidelines: Lifting up the handle opens the cover of the grinding chamber. The grinding parts can be cleaned with a brush within a couple of minutes and the machine is ready for the next batch of grinding. If required, the grinding chamber can also be washed with water. Remove the cotton bag and the screen, close the cover tightly and start the grinder. Now pour a bucket or two of water into the hopper. The grinding parts will be flushed with the water and cleaned. Continue running the machine for a few more minutes as the draft of the fresh air sucked into the grinder will dry it.The beaters, when worn out, can be removed and reversed by unscrewing the two allen-screws holding the outside rotor plate. When both the edges are worn out, they can be sharpened on an emery stone and reused as new. When completely worn out, the tips can be re-welded in Manganese Steel, Ground to Size for equal weight and refitted.

ACG Series, Fully Automatic machines deliver stacked cones cups and moulded cones ready for packing, Choice of heating by gas or with electricity, A Scraping Knife trims off excess batter, after which the cones are ejected, discharged and stacked, Special walled construction and thermal insulation ensures energy efficiency.

We specialize in manufacturing, exporting and supplying a qualitative range of Chalk Making Moulds. Designed and developed with utmost care, these devices are available in all standard and technical specifications. Our products are available in various dimensions, sizes and technical specifications as per the exact requirements of clients. Besides, our experienced quality controllers quality check these devices on various parameters before delivery to offer flawless range at our clients end. Gun Metal Chalk Mould with Copper Pins on fibre glass plates for ejection of chalk sticks.

Polishing Barrel - Made of 3 mm M.S. Sheet.- Fitted with reduction gearbox to control speed

- The sifting machine is ideal for fast economical sieving of flour for bakeries, chemical and related products and Pharmaceutical plants. - The machine airs and sieves the flour- Can be used by manually operated or semi-automatic bakeries- A rotating feeder throws the flour into a horizontal conveying system to a vertical conveying screw- The sifting drum loosens the flour which is then fed into the mixing bowl- The bowl of Dough Kneader / High Speed Mixer / Spiral Mixer has to be kept under the machine. The flour will fall into the bowl after being sieved through the Stainless Steel wire mesh.- The machine is constructed on M.S. angle frame covered with M.S. sheet and duly painted. Flour sieving attachment is fitted with steel cams on ball bearings ad oil seals to avoid sound and vibration.- 24 Hours working capacity- Large hopper provided with capacity of one bag of 90 kgs. flour per batch- Simple to use with special demountable stainless steel sieve design incorporating easily replaceable mesh which is automatically correctly tensioned.- Uniformity of flow could be well adjusted and controlled by the feed controller.

- Suitable for extracting oil from Groundnut Kernels, Sesame, Sunflower, Mustard, Rap seed, Caster seed, Cotton Seed, Soya Seed, Corn Germ, Coconut, etc.- In place of Decorticator, a suitable nut cracker (for Palm nut), Coconut Cutter (for Coconut), etc. is provided.- Mill is suitable for extraction of Edible / Non-Edible Oil- From 100 Kgs. of good quality oil seeds, approximately the following quantity of oil can be extracted: Groundnut Kernels and Sesame - 45 Kgs., Sunflower - 35 Kgs., Mustard and Rap seed - 36 Kgs., Caster seed - 40 Kgs., Cotton Seed - 16 Kgs., Soya Seed - 15 Kgs., Corn Germ - 43 Kgs.- From 100 Kgs. of Coconut (Dried) 63 Kgs. of Oil can be extracted- Available in 4, 8 and 15 Ton Crushing Capacity per 24 hours.

Function:

- The Decorticator shells the groundnut (or separates the sunflower seeds)- The husk from the Decorticator and other waste wood is used to fuel the Boiler that produces the steam required for the cooking kettle- The Kernels or Oil Seeds from the Decorticator are cooked in the Steam Kettle- The Expeller crushes the cooked Oil Seeds and produces Oil and Cake- Filter Pump supplies the extracted oil to the filter press- Filter Press filters the oil to make it edible / usable