Write a Review
Our Products
Our Complete range of products are C Purlin Roll Forming Machine, Roll Forming Machines, Eye Rolling Machine, Roll Forming Machine for making 'C' Channels / Lipped C Purlins and Roll Grinding Machines.
- Designed to seal a wide range of bottles / containers made of glass, tin, HDPE, PET and aluminium with standard RO / ROPP caps - Can also be adapted to seal goldy, saline and deep seal caps- Caps to be placed manually- Can also be modified to seal rectangular tin containers from 0.25 litres to 5 litres with the help of can rest- Can also be modified to seal fresh top gas tight closures of 1/2 or 1 litre glass or PET bottle with neck holder attachment for non-rigid bottles having provision for the same - Provided with a rotary head set
| Model: | MRS-1 |
| Type: | Hand Operated |
| Cap Size (mm): | 22 - 70 |
| Bottle / Container diameter (mm): | 25 - 100 |
| Bottle / Container height (mm): | 50 - 300 |
| Output per minute: | 15 - 20 |
| Net / Gross Weight (Kgs.): | 200 / 280 |
| Overall Dimensions (m): | 0.75 x 0.70 x 2.00 |
| Shipping Volume (m3): | 1.10 |
Features: - All fabricated design- Supplied with quick lifting centre pin arrangement with hand operated lever- Capacity maximum of leaf eye rolling 100 x 12 mm
Installation: - The machine should be installed on a concrete foundation close to the heating furnace. Hot end chambers / pre-bending of leaf spring should be done.- After Hot end chamfering of lead on press, hot flat end should be reheated. Two Eye Rolling diameter pins should kept ready. One pin is used for eye rolling while the other pin cools in the water tank kept below the eye rolling machine. Corresponding to the pin size, the required bush is to be mounted on the Eye Rolling Machine. Please make all size pins and corresponding bushes as per your requirement.
Brief Operation: Put eye rolling pin in its position. Place the pre-bent portion of the hot leaf into the machine, tighten the clamping screw and manually push the pivot end of the machine using a long pipe. After completing 3/4th bend / eye, release the clamping screw and pull the pivot end of the machine to the starting point. Again clamp the screw and push the pivot end again to complete the eye. Release the screw and pull the pin upwards. Remove the eye using a hammer and die correct the eye size and Inside Diameter. Put this eye rolling pin in the water tank for cooling and use the other pin for the next rolling operation.
- Machine constructed from steel- Machine fitted with a number of rolls with forming dies, through which a cut strip is passed- In a single pass, the desired 'C' Channel / Purlin is formed- Drive of the machine through machine cut gears- Rolls rotate in bearings having lubrication arrangement- Necessary guides and supports are provided for the strips to pass through rolls- Coil roll can be loaded
- Two rollers of EN-8 Forged Steel fitted in Gun Metal Bushes with lubrication system- Bottom Roll of 10" diameter with 4 steps for bending by eccentric taper roll drive- Top roll of 12" diameter- Eccentric drive shaft arrangement for the bottom roll through a eccentric cam. This squeezes the spring edges- Main Gears made of EN-8 Forged Steel, machine cut and perfectly matched to give smooth running- Drive through a 5 HP electric motor with necessary pulley and 'V' belts- Provision given on the side for squeezing edges of flats
Features:
- Compact & rigid design- Fabricated Steel Frame- Hardened & Ground 'T' type slide for better accuracy and rigidity- Heavy duty gearbox for continuous operation- Low Pressure Hydraulic Power Pack to ensure low heat and minimum maintenance- Range of Cycle Times and Rolling Speeds- Centralized lubrication of all the important moving parts
Features:
- Compact & rigid design- Fabricated Steel Frame- Hardened & Ground 'T' type slide for better accuracy and rigidity- Heavy duty gearbox for continuous operation- Low Pressure Hydraulic Power Pack to ensure low heat and minimum maintenance- Range of Cycle Times and Rolling Speeds- Centralized lubrication of all the important moving parts
- Machine constructed from steel
- Machine fitted with a number of rolls with forming dies on its end, through which a cut strip is passed
- In a single pass, the desired strip is formed, suitable for making rolling shutters
- Drive of the machine through machine cut gears
- necessary guides and supports are provided for the strips to pass through rolls
- Coil roll can be loaded
- 6 Station Machine for making One profile, 7 Station Machine for making Two profiles, 8 Station Machine for making Three profiles of Rolling Shutter Strips / Slats
| Model: | RSS-4.5/LD | RSS-4.5 | RSS-5.0/LD | RSS-5.0 | RSS-6.0/LD | RSS-6.0 |
| Capacity - Width of Strip: | 4.5" / 115 mm | 4.5" / 115 mm | 5.0" / 127 mm | 5.0" / 127 mm | 6.0" / 152 mm | 6.0" / 152 mm |
| Capacity - thickness of sheet (mm): | 0.4 to 0.9 | 0.7 to 1.2 | 0.4 to 0.9 | 0.7 to 1.2 | 0.4 to 0.9 | 0.7 to 1.2 |
| Capacity - Max. length: | no limit | no limit | no limit | no limit | no limit | no limit |
| Size of formed rolling strip (round type): | 3" / 76 mm | 3" / 76 mm | 3.35" / 85 mm | 3.35" / 85 mm | 3.75" / 95 mm | 3.75" / 95 mm |
| Number of Rolls: | 6, 7 or 8 pairs | 6, 7 or 8 pairs | 6, 7 or 8 pairs | 6, 7 or 8 pairs | 6, 7 or 8 pairs | 6, 7 or 8 pairs |
| Machine Speed (Feet / Minute): | 20 | 20 | 20 | 20 | 20 | 20 |
| Machine Speed (Meters / Minute): | 6 | 6 | 6 | 6 | 6 | 6 |
| Motor (HP): | 5 | 5 | 5 | 5 | 5 | 7.5 |
| Net / Gross Weight (kgs.): | 950 / 1300 | 950 / 1300 | 1100 / 1450 | 1100 / 1450 | 1200 / 1600 | 1200 / 1600 |
| Dimensions (m): | 2.0 x 1.4 x 1.1 | 2.0 x 1.4 x 1.1 | 2.2 x 1.5 x 1.2 | 2.2 x 1.5 x 1.2 | 2.5 x 1.6 x 1.4 | 2.5 x 1.6 x 1.4 |
| Shipping Volume (m3): | 4.0 | 4.0 | 5.0 | 5.0 | 6.0 | 6.0 |
Maneklal And Sons (Exports) (Maneklal and Sons (Exports))
67 Bajaj Bhavan, Nariman Point, Mumbai - 400021, Maharashtra
Share us via
