Overall Dimensions (m) : 1.88 x 1.17 x 1.78,1.95 x 1.20 x 1.78
Pump and Gallery Leakage Testing, Checking Coupling Timing Mark, Phasing the Pump, Calibrating (Flow Testing) the output of each element of the pump, Setting the Pump for Maximum Output, Complete Cut-off, Checking of Governor and Feed Pump Testing.more...
Mechanical Variable Speed Drive with the help of expandable compound pulley system and dual belt fitting with standard drive shaft coupling, Shaft Bearing, self aligning, self lubricating, totally enclosed, Measuring panel can be swiveled on either side at 180o for right and leftmore...
This ESD workbench consists of 0-125V DC 0-10A supply integrated into ESD cockpit, Digital Multimeter, Calibrator and Three Phase Calibrator integrated in 19’’ cabinet. In this case provision for 3 parallel outputs for Calibrator has been made in 19’’ cabinet. This systemmore...
We are offering microcontroller trainer kit. 8051 / 89c51 cpu operating at 10 / 12mhz 16k bytes of eprom with 8k bytes of battery backup ram 48 i/o lines, three channel timer/counter, pc serial interface using usart, interrupt controller six digit seven segment display with 28 kemore...
3 relays can be at a time checked for continuity and reliability to heat. (The number of relays to be tested can be customized). The panel can work in Manual mode: Here all the settings for current and primary voltage are done manually. The test would only start when the Heating more...
The cycle time is around 7 seconds for 4 pole MCB (less than 2 seconds per pole) Can be used for both production and R&D purpose with report generation and statistical analysis (Gives a glimpse of the test results instantaneously) Current setting is instant without any auto transmore...
The SCR Elektroniks 3 station Socket Endurance Test Bench is designed to verify the endurance testing of sockets as per IEC 60884, IS 1293 and BS 1363. Typical sockets ratings covered are for the entire range (typically 6 – 32 A) for both 3 phase and single phase loads. Featmore...
We are offering vibration test bench. multi test bench comprises of the following high pressure (10 to 4000) bar pressure cyclic test ( 0-400)bar vibration test -motorised (23-47) hz static test (gas) (0-150 )bar vacuum test (0-760)mmhg thermal test (0-600) deg c pull out (tensilmore...
Bharat Bijlee offers a complete solution for Test benches. The wide range of Automation products BBL offered are VFD’s (F5) up to 900Kw.Active front end (R6) up to 800 Kw, AC Induction motors, AC Servo motors, AC Asynchronous Servo motors, PLC’s for following test bench applimore...
The Main purpose of this panel is to Test Instrument like single phase three phase motor, thyristors transformers, various parameters like current, voltage, resistances etc.Acting as a 24 Vdc power supply, DOL(direct online starter) starter, star delta starter, Radical calibmore...
Sci-tech transformer test benches are suitably designed to test transformers up to 1500 kva capacity with hv winding voltage range from 1.1 kv to 11 kv & lv winding voltage of 433 v, ac, 50 hz and impedance voltage up to 8%. more...
The performance of a Diesel Engine depends upon its injection pump. Diesel fuel pump test benches records and sets the performance of the fuel injection pump to the maximum accuracy. more...
The performance of a Diesel Engine depends upon its injection pump. Diesel fuel pump test benches records and sets the performance of the fuel injection pump to the maximum accuracy. more...
The performance of a Diesel Engine depends upon its injection pump. Diesel fuel pump test benches records and sets the performance of the fuel injection pump to the maximum accuracy. more...
The performance of a Diesel Engine depends upon its injection pump. Diesel fuel pump test benches records and sets the performance of the fuel injection pump to the maximum accuracy. more...
Test Benches are widely used for various types of Voltage testing, Current testing. Our test benceh contains multifuntion meter , variable AC source, Variable DC source. more...
Manufacture and Supply: Test Benches for Avionic Components. Test Benches for Electrical Components. Static Frequency Converters. Aircraft Battery Charger. Capacity Testing Unit. more...
Structure and Features:︰ The water meter test bench is made up the platform, clamps, back and front pipe, flow counter group, standard measuring instrument and the outlet valve. When the inlet is connected with the stable water source, the water will get to the standard measumore...
Fully automatic three phase energy meter test bench offered by us comply with the standard of IEC 60736 testing equipment for electrical energy meters and IEC62053 standard with electricity metering equipment. These are used in test functions like Warm up, Basic error test, standmore...
The orifice assembly or the flow control element, valve, is calibrated under fluid mechanics standards of ISO 5167 and IEC 60534 standards. The process and the procedure of the measuring flow calibration of the device and the design is as per the international standards applicablmore...