Write a Review
Our Products
Our offered Product range includes MICRO-Cutter MIC, Automotive and Universal Tool Set, Bandsaw MBS, MICRO Shaper and Flexishaft.
MICRO-Cutter MICNO 28 650
For cutting wood, plastics, glass fibre reinforced plastic, paper, cardboard, foils and similar materials. With 0.5mm cutting width.
Slim and light: A diameter of just 36mm makes the ergonomically shaped casing easy to handle. A powerful DC special motor in this compact device ensures an astonishingly high cutting performance. With screwdriver for saw blade replacement.
Technical Data:
230V. 40W. 20, 000rpm. Maximum cutting depth 4mm. Cutting width 0.5mm. Weight approx. 300g. Insulated to class 2.
Double ball bearing mounted aluminium pulleys. Sturdy, plane-milled table with slot for mitre gauge (tilts through 45 for accurate mitre sawing). Triple ball bearing blade guide system, adjustable in height and width for different widths of saw blades. Low noise 220V motor (high quality, for quiet, prolonged use) with Optibelt toothed belt. Electronically controlled speed for exceptionally accurate cutting (no subsequent finishing necessary !). A table indicates the recommended speed for practically all kinds of material. The blade size of 5 x 0.4mm is ideal for fine work and allows for cutting of small radii.
230V. Blade speed adjustment from 180 to 330m/min (feedback effect). Throat 150mm, maximum height 80mm. Table 200 x 200mm (tiltable from 0 to 45). One blade 1, 065 x 5 x 0.4mm (14 TPI) is included.
Blade guide, separately
NO 28 187
Standard bandsaw blade
Of hardened Swedish steel. Fine-toothed (24 TPI). For steel and brass.
NO 28 174 1, 065 x 5 x 0.4mm
Extra narrow bandsaw blade (3.5mm) for tight radii
Of special tempered steel, with induction-hardened coarse teeth (14 TPI). Especially suited for aluminium and plastics.
NO 28 180 1, 065 x 3.5 x 0.5 mm
Bandsaw blade of bimetal
Carrier belt of alloyed tempering steel, sawing teeth of wear-resistant high-speed steel. Varying teeth 10 14 TPI. Ideal for cutting all standard steel qualities, non-ferrous metals and stainless steel.
NO 28 172 1, 065 x 6 x 0.6mm
Diamond blade
For cutting stone, ceramics, glass or glass-fibre reinforced plastics. Only proper cooling will ensure optimally cut glass or ceramics and enable a long service life of the band. Sparingly coolant liquid can be applied with a brush
NO 28 186 1, 065 x 3 x 0.3mm
Band knife of hardened spring band steel
For cutting foam, plastic, rubber, leather, cardboard and paper board.
NO 28 184 1065 x 6 x 0, 4mm
Now in its 7th generation. If you are looking for a better one, you are probably wasting your time.
14-piece combination spanner set from 6 - 19mm. 14 1/2"-sockets in sizes 8 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 21 - 22 and 24mm. Reversible ratchet. Universal joint. 1 each 125 and 250mm extensions (latter with T-bar and 1/2" square for use on wheel nuts). Spark plug sockets 16 - 18 and 21mm.
FLEX-DOT screwdriver set: slotted screwdrivers each 1 in sizes 3.0 - 5.5 and 8.0mm. Phillips (PH) screwdrivers each 1 in sizes 1 and 2. Pocket key set 8-piece for Allen screws (HX) from 1.5 - 8.0mm. Same for TX screws from TX 9 - TX 40. Automotive headlight tester with cord and crocodile clip (for car electrical systems).
Knipex 180mm combination pliers. Knipex 240mm water pump pliers. Ball-peen hammer (300g), ground on all sides and partially polished. With non-detachable graphite handle (fibre-glass reinforced, non-slip soft coating in grip area) for unparalleled vibration damping.
Ojasvi Corporation (Ojasvi Corporation)
403, Shree hari Tower,
Opp. Raj Chambers,
Khodiyar Colony
Jamnagar - 361006,
Gujarat., India
Share us via
