Other Products / Services #2030408

NO 28 644

For the carving of all types of wood. For the restoration of furniture. For the restoration of antiques. For linocuts and precision paint removal.
It is also possible to process plaster. Special, balanced, low noise DC motor with extreme high life expectancy. Gear head made of die-cast aluminium. Main housing of glass-fibre reinforced POLYAMIDE. Three high-grade Japanese knife inserts made from bimetal (U-form, V-form and flat blade) are included. In an attractive and extremely stable case made of high-grade polypropylene.

Technical data:
230V. 50W. Stroke speed 11, 000rpm. Length 230mm. Weight 680g. Class 2 insulation.

NO 28 566

For slotting, milling grooves and milling edges.
Regardless whether with parallel limit stop (maximum throat 150mm), for circular milling with centring pin (100 - 400mm) or freehand. Adjustable depth control with preselectable stroke. Ideal also as drilling guide for round parts through prism in the guiding plate.

For perfect surfaces even in tight spots: For finishing of blank surfaces, cleaning, rust removal, for the finishing touches after varnishing.

Balanced special motor, powerful, quiet and long-lasting. Quiet planetary gear in die-cast aluminium housing and continuously variable speed control (full-wave electronics) for low and constant speeds even during high contact pressure.

Main housing of glass-fibre reinforced POLYAMIDE with soft component. Securely stored in stylish case made of high-grade polypropylene with original equipment for immediate use. Rubber backing disc with hook and loop fastening, polishing sponge (medium hard), lambswool polishing disc, polishing felt for metals and non-ferrous metals (medium hard), 12 sanding discs K 2000 and NIGRIN polishing emulsion (75ml) as well as a microfibre cloth.

Technical data:
230V. 100W. 800 2, 800rpm Length 270mm. Weight 720g. Insulated to class 2.

With ball joint. To be rotated and swivelled in all directions.
20mm collar for MICROMOT drilling and milling devices, such as FBS 240/E, FBS 12/E, IBS/E, LBS/E, MICROMOT 50, 50/E and 50/EF. Made of die-cast ZINC. With clamp for quick and secure fastening to workbenches and table tops up to 60mm thickness. Alternatively, it can also be fixed to any workplace with 2 standard screws.

screwdriver MIS 1

With pre-selectable torques of 0.35 - 2Nm.
Small, light and easy to handle. An ideally positioned rocker switch provides on/off/reverse. A chuck facilitates acceptance of all bit shanks of up to 6.5mm (also for standard 1/4" bits). Housing of glass fibre-reinforced POLYAMIDE. Complete with 16 inserts of chrome molybdenum steel.

The depicted mains adapter MICROMOT NG 5/E is not included.

Engraving kit GG12 with special balanced, powerful, quiet and longlasting DC motor.
Housing of glass fibre-reinforced POLYAMIDE. Plus mains adapter, trial glass, motifs and instruction booklet as well as all necessary bits: 1 and 1.8mm diamond grinding bits with spherical head for engraving and line work, silicon carbide grinding bits in both conical and bullet shape for frosting glass as well as one corundum grinding bit in ball and cylinder shape for grinding and engraving. Including bit holder usable for holding MICROMOT rotating bits. Complete with mains adapter 0.5A for 230V.

Technical data for GG 12:
Direct voltage 12 18V. 20, 000rpm. Length 145mm. Weight 50g.

NO 28 635
Engraving tool GG 12, available individually
Includes 1 diamond bit (spherical head, 1.8mm). For operation a mains adapter is required. We recommend MICROMOT mains adapters NG 2/S or NG 2/E.

Made of solid aluminium with surface treatment and fitted with adjustable dovetail gibsand three T-slots of the MICROMOT standard (12 x 6 x 5mm). Adjustable ruler eases workpiece positioning. Both handwheels have zero-resettable dials with graduations indicating 1 revolution = 1mm and 1 division = 0.05mm. The clamps and securing bolts for the MB 200, MB 140/S and TBM are included.

Other technical data:
Table size 200 x 70mm. X travel 134mm and Y travel 46mm, maximum height 43mm.

Rotates in all directions. Made of die-cast zinc.
Easily clamps to workbenches and tables of up to 60mm. Alternatively, use 2 standard screws to secure to the work surface. Ball and socket: rotates in all directions (even downwards). 75mm jaws with protective covers (for delicate workpieces). Maximum clamping width 70mm and weight 1.6kg.

Small, robust and powerful. Complete with 3 additional nozzles.
For shrinking sleeves, shaping and welding plastics, soldering and de-soldering of electronic components. For removing layers of paint and varnish without aggressive chemicals (pickling agents). For drying and accelerating curing processes (adhesives, paints). For applying and removing films (stickers). For browning wood. Housing of glass fibre reinforced POLYAMIDE with soft components in the grip area and footprints for stationary use. A powerful heating element ensures a consistent temperature in 2 stages with an air flow of approx. 180l/min. Installed thermostat as security against overheating.

Technical Data:
230V. 500W. Air temperature in Stage 1: 350 C. Stage 2: 550 C. Air volume approx. 180l/min. Weight approx. 500g.

Used for soldering, de-soldering, brazing, heating of workpieces, tinning.
Individually controllable gas and air supply. Super fine flame shape with temperature attaining 1, 200 C. Ideal for precision work. Fitted with an electronic piezo crystal lighter.

Ideal for architectural models, designers, decorators, artists, teaching too, prototypes as well as classical railroad, plane and boat model building.

Note:
The units double wound transformer and insulation to class 2 ensure the cutter is absolutely safe. The cutting wire operates at 10V, 1A.

The large base with 390 x 280mm table with surface of aluminium cobond compound ensures smooth and easy movement of the workpiece. The printed grid and protractor ease division and cutting. The solid aluminium overarm has a 350mm throat and offers 140mm capacity in height. The holder and wire coil (30m, 0.2mm diameter is included) may be shifted along the overarm to enable mitre cutting. A LED indicates operation and prevents burnt fingers (the cutting wire heats to maximum in less than 1 second).

Other technical data:
230V, 50/60Hz. Transformer secondary max. 10V, 1A. Cutting wire temperature with 0.2mm diameter is variable between approx. 100 and 200 C. Weight approx. 3kg. Insulated to class 2 requirements.

Turning in miniature is a pleasing hobby.
One can make glasses, cups, saucers, vases and columns for a doll house. In model trains, one can make lighting masts, windows, tanks. Limbs for marionettes and hundreds of classical miniature turning tasks may be carried out with ease. The electronic speed control assists in the lower range in a semi-automated painting process.

Technical data:
Motor 230V. 100W. 50/60Hz. Centre distance of 250mm, 40mm swing. 25mm swing over support. Variable speed control covering between 1, 000 and 5, 000rpm. Headstock spindle bore of 10mm. Tailstock travel 20mm. Includes 6 collets (2 3 4 6 8 10mm), drive centre, live centre and face plate.

Grinding and polishing machine SP/E

The slim housing facilitates the grinding of long workpieces and includes an adapter to connect a vacuum cleaner to the unit.
The tool rests and eye guards are both adjustable. A spindle lock eases the changing of wheels and discs. Supplied with a 50 x 13mm corundum (grade N) and silicon carbide (soft compound) wheel for general grinding/sharpening and hard materials respectively. The right hand spindle accepts the polishing arbor, which is supplied as standard equipment.

Technical data:
230V. 3, 000 - 9, 000rpm. Wheels 50 x 13 x 12.7mm. Grinding speed 8 - 24m/sec. Weight approx. 1, 200g. Size approx. 250 x 130 x 100mm.

Accurately cuts small items of metal, wood and plastic.
Table moveable through 45, allowing mitre cuts. Workpiece is fastened tightly and accurately by means of the integrated clamping device. Clamp jaws 27mm wide and maximum workpiece diameter 20mm. Depth of cut to 13mm. A special slot is provided to clamp HO model tracks. The fence accepts lengths up to 140mm. Five ceramic cutting discs 50 x 1 x 10mm are also included suitable for cutting steel, non-ferrous metals as well as wooden or plastic rods.

Technical Data:
230V. 85W. 50/60Hz. Peripheral speed 20m/sec. Weight approx. 1.5kg.

Shaft drive via toothed belt: The motor no longer limits the working area. The slim housing around the main shaft even enables machining the surface of very long and variously shaped work pieces.

Load bearing side parts made of aluminium with milled bearing seats enable very quiet low-vibration operation.
With long, ball bearing mounted main shaft (distance from disc to disc approx. 360mm) and adjustable protective guards to work cleanly with polishing pastes. Powerful drive through DC motor with speed control (full-wave electronics). For high starting torque and enormous traction even during strong contact pressure. Firm mounting with screws, but also with the attached screw clamp in horizontal or vertical position.

Supporting construction all made of die-cast aluminium with CNC-machined fits. Pre-condition for vibration-free, clean planing of soft and hard woods.
The heart of the machine: Ball-bearing mounted planer block with exchangeable HSS blades. Belt-driven by special low noise DC motor. Plane-milled table, of which the right table half is fine adjustable via toggle screw. Adjustable longitudinal stop, to both sides inclinable through 45 (scale available). Practical safety milling protection that does not interfere during work. Main switch with emergency-stop and restart protection. Including suction connection and push stick.

Technical data:
230V. 200W. 50/60Hz. Table 400 x 80mm. Planing width 80mm. Maximum chip removal (infeed) 0.8mm. Speed 6, 000rpm. Weight 5.5kg. Insulated to class 1.

Load bearing components are all made of die-cast aluminium, with milled seats for bearings and spindles.

These characterics are essential for vibration-free, smooth thicknessing of soft and hard woods. Triple-spindled table (of die-cast aluminium, flat-milled) which can be accurately adjusted to 1/10mm by handwheel (zero adjustable). Automatic even feed with anti-kickback device: The knurled, spring-mounted infeed roller transports even irregularly shaped work pieces. A rubber-coated outfeed roller prevents marking the newly planed surface. Precision planer block with two HSS planer blades.

Technical Data:
230V. 200W. 50/60Hz. Thicknessing up to 40mm thick and up to 80mm wide. Maximum depth of cut 0.8mm. Cutter speed 6, 000rpm. Feed rate 4.8m/min. Table length 232mm. Weight approx. 8kg.

Double ball bearing mounted aluminium pulleys. Sturdy, plane-milled table with slot for mitre gauge (tilts through 45 for accurate mitre sawing). Triple ball bearing blade guide system, adjustable in height and width for different widths of saw blades. Low noise 220V motor (high quality, for quiet, prolonged use) with Optibelt toothed belt. Electronically controlled speed for exceptionally accurate cutting (no subsequent finishing necessary !). A table indicates the recommended speed for practically all kinds of material. The blade size of 5 x 0.4mm is ideal for fine work and allows for cutting of small radii.

230V. Blade speed adjustment from 180 to 330m/min (feedback effect). Throat 150mm, maximum height 80mm. Table 200 x 200mm (tiltable from 0 to 45). One blade 1, 065 x 5 x 0.4mm (14 TPI) is included.

Blade guide, separately

NO 28 187

Standard bandsaw blade
Of hardened Swedish steel. Fine-toothed (24 TPI). For steel and brass.

NO 28 174 1, 065 x 5 x 0.4mm

Extra narrow bandsaw blade (3.5mm) for tight radii
Of special tempered steel, with induction-hardened coarse teeth (14 TPI). Especially suited for aluminium and plastics.

NO 28 180 1, 065 x 3.5 x 0.5 mm

Bandsaw blade of bimetal
Carrier belt of alloyed tempering steel, sawing teeth of wear-resistant high-speed steel. Varying teeth 10 14 TPI. Ideal for cutting all standard steel qualities, non-ferrous metals and stainless steel.

NO 28 172 1, 065 x 6 x 0.6mm

Diamond blade
For cutting stone, ceramics, glass or glass-fibre reinforced plastics. Only proper cooling will ensure optimally cut glass or ceramics and enable a long service life of the band. Sparingly coolant liquid can be applied with a brush

NO 28 186 1, 065 x 3 x 0.3mm

Band knife of hardened spring band steel
For cutting foam, plastic, rubber, leather, cardboard and paper board.

NO 28 184 1065 x 6 x 0, 4mm

Plane-milled worktable of die-cast aluminium (220 x 120mm) with adjustable fence and scale as well as threaded holes for securing the MICRO compound table KT 70.
Solid steel column (20 x 340mm). Adjustable fence with scale. Solid, hard-chromed steel column, 340mm high, 20mm diameter. Super stable die-cast head with VDE approved motor. Very quiet and of long life expectancy type. Power transmission by aluminium pulleys and flat belt. Three spindle speeds (triple torque at low speeds). Feed lever with adjustable depth scale.

Technical data:
230V. 85W. 50 60Hz. Spindle speeds of 1, 800, 4, 700 and 8, 500rpm. Extremely high rotational accuracy, 30mm feed. Throat depth (column to drill spindle) 140mm. Six triple slit precision collets for shaft sizes 1 1.5 2 2.4 3 3.2mm are included. 3/8" thread. Weight 3.3kg.

Compact workshop vacuum cleaner CW-matic NO 27 490

The vacuum cleaner runs as long as the machine runs. There is a follow-up time of 5 seconds after switching off the power tool.
Smooth operation with high suction capacity. With large fluted filter made of POLYPROPYLENE to be cleaned and washed manually. Additional fine dust paper filter (not essential for this function). Container is easily emptied by removing the appliance lid with the motor unit. Blowing function available by refitting the vacuum hose. Also suitable for vacuuming liquids. Complete with 3.5m vacuum hose, 2-part aluminium vacuum pipe (98cm), floor nozzle, brush nozzle, crevice nozzle and adapter for connection to standard adapter of all such equipped PROXXON machines. Practical holder for the suction connection included (description on the left). Supplied with 6 fine dust paper filters.

Technical Data:
230V. 1, 100W. Connection for electric tools from 25 to 2, 000W. Container 18l. With 5m connection cable.

An accurate device for parallel drilling, thread-cutting and milling. Made of high-precision aluminium die-casting.
With two-way pivotable articulated arm and 20mm standard collar. Once the device is clamped, it always remains vertically aligned. This means that, e.g. drill holes are always exactly perpendicular to the work piece surface! Preselectable drill depth using depth control with easy-to-read scale. After drilling, an adjustable spring automatically pulls the device back into its top rest position.
Plane-milled solid base plate with 200 x 200mm usable table area and two continuous MICROMOT standard T-slots (12 x 6 x 5mm). Stable drill column ( 45mm, 500mm long).

The standard 20mm collar enables precise clamping of the drilling device such as the precision drill/grinder FBS 240/E, professional drill/grinder IBS/E, long neck straight drill/grinder LBS/E, MICROMOT 50, 50/E, 50/EF and MICROMOT 230/E.

With standard 20mm collar for all MICROMOT drilling and milling units which are equipped with steel collets.
For engraving letters, numbers and individual shapes on metal, plastics, glass or stoneware. For name plates, jewellery or valuable materials. Also easy to manufacture miniature, individual shapes, engravings, cut-outs and outline shapes, even in series, using self-made templates or commercially available templates (plants, animals, coats of arms).
Guide bar (template holder) holds a maximum of 14 letters. Template contours are precisely to be followed using the guide marker (ball handle).
The lettering to be milled is scaled down during transfer. The transfer ratio can be fixed at 2:1, 3:1, 4:1 or 5:1 by simply adjusting two screws. The work piece is aligned and fixed on the movable guide block with clamping jaws (here MICROMOT clamping jaw set NO 24 256) or a vice.

Scope of delivery:
two sets of letters from A to Z, incl. hyphen, full stop and slash (total 52 items), one each HX key 1.5 3 and 5mm as well as a HX (ball head) screwdriver 2.5mm. Complete with a comprehensive instruction manual.

Stencil set for engraving device GE 20
Letters A Z, incl. hyphen, full stop and slash. Also numbers 0 9. For use with guide bar of the GE 20.

Easy sharpening of drill bits from 3 to 13mm diameter, standard angle of 118.
Note:
Operating the Drill sharpener BSG 220 is quite simple. Also untrained users will be able to re-sharpen spiral drills according to DIN. In order to obtain satisfactory results though, it is important to study the product manual attentively before working with this machine. Starting without reading these relevant instructions, one will not be able to achieve the expected precision.

This moves from left to right and also rotates the drill bit on its own axis. This operation yields the correct relief angle. The carriage is fitted with a feed screw for fine feed. A dressing stone, ensuring a sharp cutting surface, is also fitted.

Other technical data:
230V, 85W. Corundum grinding disc size 50 x 13mm. ABS housing with fixing holes. Weight 1.7kg. An easy to understand operating manual and replacement disc accompany the unit. For further spare discs see page 36.

Centre distance 250mm. Swing 70mm. Height over cross slide 43mm.

Machine bed: Of cast iron, wide-legged prismatic guide. For vibration- free work even at high loads. Rear flange for mounting the mill/ drill head PF 230. Covered lead spindle.

Headstock:Of die-cast aluminium. Precision bearing mounted main spindle (run-out without chuck 1/100mm) with 10.5mm opening. Chuck side 70mm hollowed to 14mm. With MK 2 bore. Rotary switch for engaging the automatic feed via lead and feed spindle (optionally 0.05 or 0.1mm/rev.).

Tailstock:Of die-cast aluminium. Sleeve 20mm, retractable up to 30mm. With millimetre scale, MK 1 bore and live centre.

Support:Bed carriage made of die-cast zinc. Cross slide and top slide of steel (adjustment 60 or 45mm). Turning tool post for cutting tools size 8 x 8mm.

Drive:Quiet DC special motor with 3-stage belt drive for 300 900 and 3, 000rpm. With additional speed control (full-wave electronics) continuously adjustable to 100 300 or 1, 000rpm, depending on belt ratio. Clockwise - anticlockwise rotation. Main switch with emergency stop function and restart protection.

Lathe chuck:High quality 3-jaw chuck as per DIN 8386 Class 1 (concentricity tolerance 0.04mm). Capacity through reversing jaws from 2 - 75mm. Including lathe chuck guard with safety shutdown.

Handwheels:Of aluminium, with adjustable scale ring (1 division = 0.05mm, 1 revolution = 1mm).

Thread cutting device:With change gears for left-hand and righthand threads of the most important metric pitches (0.5 0.625 0.7 0.75 0.8 1 1.25 1.5mm).

Other technical data:
230V. 50/60Hz. Size L 560, W 270, H 170mm. Weight approx. 12kg.

With large multi-function display, 3 glass rulers (with one sensor each) and fastening elements.
Reasonable for repetitive machining: A second start point in addition to the zero point can be set anywhere. Most important computing functions:
- Calculation and indication of a centre position
- Basic arithmetic operations
- Positioning of drill holes on any straight lines and circular paths
- Milling of crooked planes
- Milling of radii in different planes

Technical data:
Digital display 265 x 182 x 48mm for 110 230V. 50/60Hz. Glass rulers for travel distances: vertical (z-axis) 220mm, transverse (x-axis) 300mm, depth (y-axis) 100mm. With a 200cm metal-sheated plug connecting line to the display.

For stationary use of MICROMOT electrical precision tools with metal head in combination with a vise.

Especially suited for industrial drill/grinder IBS/E, belt sander BS/E, longneck angle grinder LHW, super jig saw STS/E and delta sander OZI/E. Made of glass-fibre reinforced POLYAMIDE.

MICRO-Cutter MICNO 28 650

For cutting wood, plastics, glass fibre reinforced plastic, paper, cardboard, foils and similar materials. With 0.5mm cutting width.

Slim and light: A diameter of just 36mm makes the ergonomically shaped casing easy to handle. A powerful DC special motor in this compact device ensures an astonishingly high cutting performance. With screwdriver for saw blade replacement.

Technical Data:
230V. 40W. 20, 000rpm. Maximum cutting depth 4mm. Cutting width 0.5mm. Weight approx. 300g. Insulated to class 2.

For use with pneumatic screwdrivers 1/2" (12.5mm). High alloy special steel for superior wear resistance and a maximum torque of 500Nm. Extra long (85mm). In sturdy steel box (powder coated).

NO 23 9381 piece each 17 - 19 and 21mm


IMPACT sockets (individually), as described above

NO 23 962Size 17
NO 23 964Size 19
NO 23 966Size 21

For chamfering, cutting grooves, slots, recesses, radii and other profiles.

For crafting picture frames and for separating. Also enables exact manufacturing of edges and longitudinal cuts (for model building, e.g. for doors, flaps and housing parts). Powerful dust-protected motor with toothed belt drive. Double ball-bearing spindle. Tool holder with triple slit precision collets (one each of 2.4 - 3 and 3.2mm are included).

Milling cutter height adjustment by hand wheel. Stable aluminium table with longitudinal and angle stop as well as cutter guard. Adapter for vacuum cleaner fits standard household vacuum cleaners. Three tungsten carbide router cutters (slot cutter 3.2mm, V-slot cutter and core box bit) are included.

Technical data:
220 - 240V. 100W. 50/60Hz. 25.000/min. Height adjustment with scale ring adjustable to 0 (1 revolution = 1, 1 graduation = 0.05mm). Milling table 300 x 150mm. Weight approx. 2.0kg.

The maximum speed of 20, 000rpm is continuously variable down to 5, 000rpm. The full wave electronic speed control results in virtually constant torque, even at lower speeds, in turn facilitating micro drilling, cleaning and polishing. The spindle runs in a precision ball bearing and is lifted with a lock button. The 20mm collar fits MICROMOT drill stands and vices. The machine is fitted with a special, balanced, low noise DC motor with high life expectancy. Stable housing of glass-fibre reinforced POLYAMIDE with soft components in the finger grip area. Complete with 43 quality inserts in a sturdy plastic case.

The heart of our MICROMOT precision tools for 220 - 240V:the direct current (DC) special motor.

Technical data:
5, 000 - 20, 000rpm. Maximum power consumption 100W, 220 - 240V. Length 200mm. Weight 450g. Insulated according to class 2 requirements. Keyless chuck with 0.3 - 3.2mm capacity.

Sockets from 8 - 34mm (the latter for M 22 according to new standard). Deep sockets for protruding bolts sizes 13, 17 and 19mm. Spark plug sockets 16 and 21mm. See photo for full content.

The ratchet - the key item. Made from CrV steel in one single piece. Hardened and with perfect toothing: several of the 52 teeth engage simultaneously for transmitting extremely high torque. Quick release mechanism: releasing sockets at the push of the button.

Sturdy, welded steel box, powder coated for durability. With distortion-free, indestructible trays of injected POLYPROPYLENE. Oil and acid resistant and easy to clean. With easy-to-read and durable marking of all socket sizes!

Baton ratchet 1/4''. Our sturdy ratchet!

Fine tooth drive: Many teeth of the 45 teeth engage simultaneously for transferring high torques. Reversing lever for ratcheting direction. Quick-release button for ejecting sockets. Head and shaft forged from one CrV steel billet. Double nickel plated with matt chrome plated finish. Grip of oil and acid-resistant TPR (thermoplastic rubber) with practical hole for hanging up.

Now in its 7th generation. If you are looking for a better one, you are probably wasting your time.

14-piece combination spanner set from 6 - 19mm. 14 1/2"-sockets in sizes 8 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 21 - 22 and 24mm. Reversible ratchet. Universal joint. 1 each 125 and 250mm extensions (latter with T-bar and 1/2" square for use on wheel nuts). Spark plug sockets 16 - 18 and 21mm.

FLEX-DOT screwdriver set: slotted screwdrivers each 1 in sizes 3.0 - 5.5 and 8.0mm. Phillips (PH) screwdrivers each 1 in sizes 1 and 2. Pocket key set 8-piece for Allen screws (HX) from 1.5 - 8.0mm. Same for TX screws from TX 9 - TX 40. Automotive headlight tester with cord and crocodile clip (for car electrical systems).

Knipex 180mm combination pliers. Knipex 240mm water pump pliers. Ball-peen hammer (300g), ground on all sides and partially polished. With non-detachable graphite handle (fibre-glass reinforced, non-slip soft coating in grip area) for unparalleled vibration damping.

Carefully hardened and plated. With clearly readable sizes.
Includes 6 x 7, 8 x 9, 10 x 11, 12 x 13, 14 x 15, 16 x 17, 18 x 19 and 20 x 22mm. Supplied with a plastic holder with slot for each spanner and holes for attaching to a wall. All spanners clearly labelled to make them easy to find.

NO 23 800set

• Optimal surface protection by means of double nickel-plating and single chrome-plating. With easy to hold, smooth finish.
• With durable laser inscribed and clearly readable sizes in mm.
• Polished heads: slim and thin walled. Torque characteristics still exceed DIN/ISO requirements.
• Dimensional tolerances are better than those required by DIN/ISO. Each piece is calibrated and checked.

Spanners 6 - 19mm. One each in sizes 6 x 7, 8 x 9, 10 x 11, 12 x 13, 14 x 15 and 17 x 19mm. Reliable ratchet mechanism with inner ring gear of CrV steel (reversible). Packed in sturdy steel box (powder coated) with flap clasp. Tray with practical recess area for storage of small parts (the depicted nuts are not included in the scope of delivery).

Automatic quick-release when tightening screws: Clearly audible and palpable click signal when the selected torque is reached.
Pre-setting of the torque by turning the knurled ring at the end of the handle (lockable). Clearly legible scale display. 50mm long slim shaft with magnetic holder for 1/4" (6.3mm) standard bits. Includes adapter with 1/4" male hexagon drive to 1/4" male square drive for sockets. Accuracy +/- 6 %. Total length 170mm. Weight 135g.

Extra-long version with soft-finish skin-friendly handle made of oil and acid resistant TPR (thermoplastic rubber) with hanging hole. Slim head with ground jaws. Accurate control of flexible jaw with smoothrunning adjustment via knurled screw. Easy to read millimetre scale for defining size across flats and measuring work pieces.

With spherical finish on the long end (short end chamfered). One each 1.5 - 2.0 - 2.5 - 3.0 - 4.0 - 5.0 - 6.0 - 8.0 and 10mm. Chrome vanadium steel. In foldable plastic holder.

Dual ball-bearinged milled steel shaft with tool holder for MICROMOT steel collets. Ball-bearinged shaft end on machine. Highly flexible core (does not run hot when working on tight radii). Length 100cm. For a maximum of 25, 000rpm. Includes 6 steel collets (1 1.5 2 2.4 3 and 3.2mm).

As described above, but with 0.3 to 3.2mm quick-action chuck. Practical when working with different shaft diameters.

Designed for sawing all kinds of metal tubes, pipes and profiles up to 125mm (5") wide. The simple adjustment of vice, cutting angle and sawing speed make it a very practical metal sawing machine for every workshop.

Features:

• Digital electronic speed regulator "constant speed'
• Double motor protection:- Average Limiter- Temperature Limiter
• Anti - reset safety function
• Steady and sturdy steel base
• User-friendly vice with clear indicators
• Ergonomic handgrip
• Adjustable bar stop rod for mass-produced cuts
• Versatile, fast and easy to use
• Wide cutting angle adjustment range
• Simple speed adjustment with quick guide

• MOTOR POWER	1010 W INPUT SINGLE PHASE MOTOR
  RATED VOLTAGE	110-120V OR 220-240V
  RATED FREQUENCY	50-60Hz
  CUTTING SPEED	adjustable, 30-80 m (100 - 265 ft) per minute
  CUTTING ANGLE	adjustable, 0-60
  SAW BAND	13 x 0.65 x 1440 mm, 10-14 TPI M42 10% Cobalt
  CUTTING CAPACITY
  RANGE AT 0	Pipe max. 125 mm (5")
  	Square 130 x 125mm (5" x 5")
  RANGE AT 45	Pipe max. 76 mm (3")
  	Square 76 x 76mm (3" x 3")
  RANGE AT 60	Pipe max. 50 mm (2")
  	Square 50 x 50mm (2" x 2")
  DIMENSIONS	650 x 310 x 450 mm (machine)
  	724 x 375 x 460 mm (packaging)

Name:TCT ANNULAR CUTTER WITH WELDON SHANK
Model:
Introduction:TCT ANNULAR CUTTERwith unique types geometry and random-space tips provide clearly cutting, fast feed rate, less vibration, smooth hole surface and long tool life, the effective of drilling is much better and quicker than the common drills.
TCT ANNULAR CUTTERcan be used on magnetic drilling presses, drilling machine and electric drill in rotary mode and all kinds of drilling presses with all types of shank

It is produced with ultrafine cemented carbide, and the end tooth geometry specially designed for rail can give it excellent service life. It is suitable for drilling of steel rails and applicable to all kinds of drilling machines for steel rails.

NO 27 110

The accurate miller for delicate projects. Spindle speeds 5, 000 - 20, 000rpm. For work with extremely small cutters.

Stable grey-cast iron machine base, vertical guide and compound table. Free from play, readjustable dovetail gib in all axes. Die-cast aluminium arm housing, with 24-pin special motor (balanced). For vibration-free work at high speeds.

The triple slit, hardened steel MICROMOT collets cover 1 - 1.5 - 2 - 2.35 - 3 - 3.2mm. The table is fitted with 3 T-slots of the 12 x 6 x 5mm MICROMOT norm. An adjustable ruler scale eases the positioning of the workpiece.

Technical data:
220 - 240V, 100W, 50/60Hz. Spindle speeds 5, 000 - 20, 000rpm. Table 200 x 70mm with X-Y travel of 134 and 46mm respectively, with vertical travel 80mm. Footprint size 130 x 225mm and overall height 370mm. Weight approx. 7kg. The clamping blocks depicted are included too, but not the workpiece!

ead with dovetail guides can be tilted through 90 (scale ring available). Enables bevelled drilling and versatile milling operations.

Geared rack and pinion feed with return spring allowing effortless and sensitive operation. Practical drill depth scale with adjustable limit stop (maximum travel 40mm). With standard 20mm collar for MICROMOT drilling and milling devices. With solid, hard chromium-plated steel column (280 x 20mm), throat capacity (column inside to centre of tool) 140mm.

Plane-milled table (220 x 120mm) with parallel limit stop and scale. Drilled, tapped holes for securing the MICRO compound tableKT 70and holes to fix the drill stand itself are also provided. Weight 2.2kg.