Details :

• Impermeable according to FM3971
• Classified for up to 90 min. Fire Rating 750C Cellulosic Fire.
• Classified for up to 90 min. Fire Rating 1100C Hydrocarbon Fire.
• Low DFT (Dry Film Thickness) of 1.6mm
• 100% UV Stable Non-Corrosive
• Non-Toxic, Non-Hazardous
• Rodent Proof Certificate (Gnawing Certificate)
• 600-700% typical Intumescent expansion after 10 minutes of exposure to 870°C

Our wide range of Spacers (Flexible & Rigid) completes our product series with jumpers and down-lead spacers complying with any applicable standard. They can also be used with any aluminium conductor with any type of configurations like Twin, Triple, Quad, Hexa or Octa and for voltages upto 1200 kV.

WBTMS integrates online temperature measurement, data collection, data analysis and control function

WBTMS consists of :

• Sensors ( Wireless Temperature transmitters – BBS350)
• Receiver (Wireless Signal Receiving & Monitoring Unit – BBC969)
• Software (Processing, Alarming & Reporting Software – AmpSCADA ** **Optional

Bus Bar Sensors :

Digital Sensors

• Measures temperature in wide range : -40 deg C to 125 deg C
• Transmission Interval : Every 30 sec to 300 sec
• Transmission Range : Upto 15-20 mtrs (Can be increased upto 4 kms with additional hardware)

Receiver :

• Receiver BBC969 is installed in the control panel
• One unit monitors 9 sensors
• Alarm Mode : Buzzer, Relay for Hooter & Relay for CB
• Depending on number of sensors, a series of BBC969 controller can connect in daisy chain on Modbus

Software (Optional) : 

• Processes the sensors’s information from Modbus
• Records in textual log file
• Display Alerts, Trend Charts & generate customize reports
• Admin User can set ALerts or generate reports

Application Area :

• Input & Output bus bar of Switchgear
• Circuit breaker contact
• Bearing & Winding of the motor
• High temperature air outlets
• Power distribution Transformers

Solutions :

• Monitoring of Transformer Oil level, Oil Temperature & Bus Bar Temperature :
• Monitoring of LV Panel Bus Bar Temperature in 12 Substations remotely connected over Wireless Communication

 Advantages:

Details :

• Up to 4 hours with single cable and tray
• Up to 4 hours E Ratings (Integrity)
• Up to 4 hours EI Ratings (Integrity & Insulation)
• 50mm to 100mm thick seals
• Easy install with Rockwool backing
• Expands on cure to seal around cable
• No Sealants required
• Load bearing
• EN1366 tested & Approved
• CE Mark and UL

The major advantages of LV ABC are:

• Total elimination of faults on LT lines
• Improved reliability
• Avoidance of theft by direct tapping
• Avoidance of overloading of Distribution transformers

Details

• Ready to install on existing bare conductor lines
• Jumpers made of MV Insulated Cable
• Customized connectors made of special alloy
• Length as per site requirements
• No faults at the jumper locations due to birds

CharCoat IC is the Vulcanized silicone Coating on the market today for the protection of Insulators from pollutants :

• Protects from pollutants and contaminating layers
• Prevents dry band layers
• Prevents partial discharge and flashover
• Improved performance due to lack of pollutants
• Stops UV, ozone and ageing degradation

Properties :

• Low DFT of 0.3 – 0.5mm
• Adhesion to glass, ceramic & resins
• BS2918 – Dielectric Strength – 64kV/mm
• IEC 93 – Surface & Volume Resistivity
• IEC 60273 – Hydrophobicity
• ASTM D 495-99 – Arc Resistance
• ASTM D 2303-97 – Tracking & Erosion
• CPRI REC Spec – Hydrophobicity recovery after 100 hours Flash over Arc test

Heat-shrink and cold-applied systems for switchgear and transformers with standardized bushings for 250A, 400A and 630/1250A have been installed by utilities and industrial organizations worldwide for more than 25 years.

• Heat-shrink and elastomeric technologies
• Right-angle insulating boots
• Straight insulating boots
• Separable screened adaptor systems for 250A, 400A and 630/1250A
• Separable insulated adaptor systems
• Suitable for crimp and mechanical lugs
• Plug in termination 1250A
• Easy and highly reliable installation
• Solutions for all cable constructions
• All products are available for 1c and 3c application

Features:

• Tool free installation
• No loose parts
• Easy to open bails permits fixing to brackets and pigtails
• Bail lengths can be adjusted up to 220 mm in four steps
• Exceeds requirements according to NFC 33 042
• Clamps made of weather and UV-light resistant glass fiber reinforced polymer
• Adjustable link made of Stainless steel and hot dip galvanized steel

Arc Suit is a specially designed protection garment used worldwide to effectively protect human life from electrical flash. They are made from special flame resistant fabric (FR) meeting IEC 61482-1 & IEC 61482-2 and tested as per ASTM 1959. They are classified as per HRC 1, HRC 2, HRC 3, HRC 4 based on the ATPV values as per NFPA 70 E.

Advantages:

• Inherently flame resistant FR fabric – properties retained over life span
• Lightweight fabric – Ranging from 6.5 to 9 oz/yard2 for user comfort
• Unique design – Various combinations for fatigue free operation
• Stitching thread – garments made with FR rated thread
• Various ATPV values garment starting from 5 & upto 100 cal/cm2
• Heat Attenuation factor (HAF) – more than 90% to ensure minimum exposure to heat
• For higher ATPV air ventilated design garments