Pali, Rajasthan, India
Our Products
Specification
1. Soft Aluminium Foil one side primer coat for printing and other side laminated with LDPE film. 2. Soft Aluminium Foil one side printed and other side laminated with LDPE film.
Application
1.The LDPE laminated soft pharmaceutical strip foil is suitable for packing the tablet, and capsules (Both side strip foil and in center tablet or capsules).
2. Suitable for Lidding Foil in certain cases.
3. Any other use with the consent of manufacturer.
Structure. 1.Primer/Alu.Foil/LDPE Film - Plain
2. Printing/primer/ Alu.Foil/ LDPE Film - Printed
CompliancesThe product is fully compliant to the tests of FDA, REACH, RoHS and anti-microbiological
DetailDescriptionoftheproduct
FoilRolled from Aluminum Alloy - AA 8011 grade imported foil stock conforming to ICH Q3D Schedule, Rolled with FDA approved consumables and international guidelines on Health and Safety.
TestCertificate:
The test certificates provided on observed values with standard parameters or mutually agreed format.
Above-mentioned specifications are for general guideline only and can be changed as part of continuous improvement programme.
The final product specification will be made as per customer requirement.
Tolerances of Foil Gauge and Unit Weight:
|
Foil Gauge mm |
Thickness mm (±8%) |
Unit Weight g/sq.mtr. (±8%) |
||||
|
Lower Value |
StandardValue |
UpperValue |
Lower Value |
StandardValue |
UpperValue |
|
|
0.025 |
0.0230 |
0.025 |
0.0270 |
62.33 |
67.75 |
73.17 |
|
0.030 |
0.0276 |
0.030 |
0.0324 |
74.80 |
81.30 |
87.80 |
|
0.040 |
0.0368 |
0.040 |
0.0432 |
99.72 |
104.4 |
117.07 |
Mechanical Properties.
|
Foil Gauge (mm) |
Surface |
Temper |
Bursting Strength(Kg/sq.cm) |
Pin Holes(Nos./sq.mtr) |
|
0.025mm |
Matt /Bright |
Soft |
1.5 Min. |
0.4 |
|
0.030mm |
Matt /Bright |
Soft |
2.3 Min. |
NIL |
|
0.040mm |
Matt /Bright |
Soft |
2.8 Min |
NIL |
LDPE Film
Low density polyethylene film is made in monolayer from 100 % virgin grade raw material with MFI of 6 to 8 and through autoclave (low pressure) process without any mix up. It is clear, transparent and treated for perfect lamination.
Tolerance of LDPE Film thickness and Unit Weight g/sq.mtr.
|
LDPE Gauge |
Thickness Tolerance (mic.) (±10%) |
Unit Weight g/sq.mtr.(±10%) |
||||
|
Lower |
STD |
Upper |
Lower |
STD |
Upper |
|
|
150 |
33.8 |
37.6 |
41.40 |
31.17 |
34.64 |
38.10 |
|
180 |
40.0 |
45.10 |
49.60 |
37.41 |
41.57 |
45.75 |
Combined unit Weight (Alu foil + LDPE) and Yield (Sq meter per Kg of laminated foil)
|
Type of Laminates |
Combined Unit Weight (Alu Foil + LDPE)Grams / Sq mtr of laminated foil |
Yield -Standard |
||
|
Lower |
STD |
Upper |
Sq Mtrs./Kg |
|
|
0.025mm Foil+ 150 Gauge LDPE Film |
93.5 |
102.39 |
111.27 |
9.76 |
|
0.03mm Foil + 150 Gauge LDPE Film |
105.96 |
115.94 |
125.9 |
8.62 |
|
0.04mm Foil + 150 Gauge LDPE Film |
130.89 |
143.04 |
155.17 |
6.99 |
|
0.025mm Foil+ 180 Gauge LDPE Film |
99.74 |
109.32 |
118.89 |
9.14 |
|
0.03mm Foil + 180 Gauge LDPE Film |
112.2 |
122.87 |
133.52 |
8.13 |
|
0.04mm Foil + 180 Gauge LDPE Film |
137.13 |
149.97 |
162.79 |
6.67 |
Recommended Operating Condition
|
Peeling Strength (Bond strength between Foil & LDPE) |
250 gms/15 mm (Min.) |
|
Sealing Strength (Bond Strength between LDPE to LDPE) |
550 gms/15 mm (Min.) |
|
Sealing Temperature |
180° C |
|
Sealing Pressure |
3.0 to 6.0 bar |
|
Dwell Time |
0.5 Sec |
Primer
A thin layer of de-waxed shellac or is applied to de-grease the foil and promote adhesion with printing ink.
Printing
|
Printing Surface |
On Primer side |
|
Design |
As per customer’s approved artwork and design. |
|
Colors |
Up to 8 Col on Primer side |
|
Length Register |
± 0.3 mm |
|
Ink Adhesion and Stability |
No peel off or breakage by scotch pull test or under sealing condition. |
Finishing
|
Reel Width |
As required within 960 mm |
|
Reel wandering |
± 0.5 mm edge wandering |
|
Width Tolerance |
±1mm |
|
Outside Diameter |
Slit Reel – 350 & Jumbo 400 mm |
|
Core & Inside Diameter |
Cardboard, Aluminium and PVC 76 mm ID suitable for shafts and pneumatic mandrel |
|
Joints |
With red / brown colored BOPP tape with flap (max 2 per reel.) |
Packing and Labeling
|
Mode of Packing |
Sea Worthy Packing |
|
Labeling |
Each Reel / Jumbo Roll is identified with a sticker, which is pasted inside the core and has got following information: -
Specification/ Gauge/ Width/ Lot No./ Operator No./ Date/ Set No./ Machine name/ No. of Joints. |
Soft Aluminium Foil one side Matt and other side Bright or Both side Bright.
To manufacturing the LDPE laminated pharmaceutical strip foil suitable for packing the tablet, and capsules.Suitable for Lidding Foil in certain cases with LDPE lamination or by doing the HSL coating. Any other use with the consent of manufacturer.
CompliancesThe product is fully compliant to the tests of FDA, REACH, RoHS and anti-microbiological
DetailDescriptionoftheproduct
FoilRolled from Aluminum Alloy - AA 8011 grade imported foil stock conforming to ICH Q3D Schedule, Rolled with FDA approved consumables and international guidelines on Health and Safety.
TestCertificate:
The test certificates provided on observed values with standard parameters or mutually agreed format.
Above-mentioned specifications are for general guideline only and can be changed as part of continuous improvement programme.
The final product specification will be made as per customer requirement
Tolerances of Foil Gauge and Unit Weight:
|
Foil Gauge mm |
Thickness mm (±8%) |
Unit Weight g/sq.mtr. (±8%) |
Yield -Standard |
||||
|
Lower Value |
StandardValue |
Sq Mtrs./Kg |
LowerValue |
StandardValue |
UpperValue |
Sq Mtrs./Kg |
|
|
0.025 |
0.0230 |
0.025 |
0.0270 |
62.33 |
67.75 |
73.17 |
14.76 |
|
0.030 |
0.0276 |
0.030 |
0.0324 |
74.80 |
81.30 |
87.80 |
12.30 |
|
0.040 |
0.0368 |
0.040 |
0.0432 |
99.72 |
104.4 |
117.07 |
9.57 |
Mechanical Properties.
|
Foil Gauge(mm) |
Wet-ability |
Surface |
Temper |
BurstingStrength(Kg/sq.cm) |
Pin Holes(Nos./sq.mtr) |
|
0.025mm |
A to C |
Matt /Bright |
Soft |
1.5 Min. |
05 |
|
0.030mm |
A to C |
Matt /Bright |
Soft |
2.3 Min. |
NIL |
|
0.040mm |
A to C |
Matt /Bright |
Soft |
2.8 Min |
NIL |
Finishing
|
Reel Width |
As required or within 960 mm |
|
Reel wandering |
± 0.5 mm edge wandering |
|
Width Tolerance |
±1mm |
|
Outside Diameter |
Max. 550 mm |
|
Core & Inside Diameter |
Aluminium with 76 mm ID suitable for shafts and pneumatic mandrel |
|
Joints |
With red / brown colored BOPP tape with flap (max 2 per reel.) |
Packing and Labeling
|
Mode of Packing |
Sea Worthy Packing |
|
Labeling |
Each Reel / Jumbo Roll is identified with a sticker, which is pasted on the top of roll and has got following information: - Specification/ Gauge/ Width/ Coil no. / Date/ Reel no./ Machine name/ No. of Joints. |
Product:-BlisterLiddingFoilSpecification
1. Hard Aluminium Foil one side under coat with primer for printing and other side coated with Heat Seal lacquer (HSL)
2. Hard Aluminium Foil one side printed to design and other side coated with Heat Seal lacquerApplication
1. The heat seal lacquer coated foil suitable in the application of Lidding foil for thermoform blister (PVC/PVDC) and cold form blister (CFB).
2. As Lidding foil in Unit Food Packaging and confectionary
3. Any other application with the consent of manufacturer.
Structure 1.Primer/Alu. Foil / Heat Seal Lacquer - Plain
2. Printing/primer/ Alu. Foil/ Heat Seal lacquer - Printed
Compliances
The product is fully compliant to the tests of FDA, REACH , RoHS and anti-microbiological
DetailDescriptionoftheproduct
FoilRolled from Aluminum Alloy - AA 8011/1200 grade imported foil stock conforming to ICH Q3D Schedule, Rolled with FDA approved consumables and international guidelines on Health and Safety.
TestCertificate
The test certificates provided on observed values with standard parameters or mutually agreed parameters.
Above-mentioned specifications are for general guideline only and can be changed as part of continuous improvement programme.
The final product specification will be made as per customer requirement
Tolerances of Foil Gauge and Unit Weight:
|
Foil Gaugemm |
Thickness mm (±8%) |
Unit Weight g/sq.mtr. (±8%) |
||||
|
Lower Value |
Standard Value |
Upper Value |
Lower Value |
Standard Value |
Upper Value |
|
|
0.020 |
0.0184 |
0.020 |
0.0216 |
49.90 |
54.20 |
58.50 |
|
0.025 |
0.0230 |
0.025 |
0.0270 |
62.33 |
67.75 |
73.17 |
|
0.030 |
0.0276 |
0.030 |
0.0324 |
74.80 |
81.30 |
87.80 |
Properties
|
Mechanical & Surface |
Pin Holes |
||
|
Surface |
Matt & Bright |
Gauge |
Nos / Sqmtr* Max |
|
Temper |
Hard H18 |
0.020mm |
10 |
|
Wet ability |
32 dynes (minimum) |
0.025mm |
05 |
|
UTS |
150 – 160 MPa |
0.030mm |
NIL |
|
Elongation |
1.5 % Max |
· Pin Holes between 20 to 50 micron measured under 1500 Lux of light |
|
Heat Seal Lacquer
Color less Polymer of Vinyl Chloride, Vinyl acetate and Di-carbonic Acid liquefied with solvent and applied in an appropriate way to achieve no retained solvent. The Heat Seal Lacquer is suitable for sealing with PVC/PVDC
|
Standard Coating Grammage |
Variation Limit |
|
4 – 6 gsm |
± 0.5 gsm |
|
5 - 7 gsm |
± 0.5 gsm |
|
6 – 8 gsm |
± 0.5 gsm |
Combined Weight and Yield ( Sq meter per Kg of coated foil)
|
Thicknessmm |
Combined Unit Weight (Alu Foil + HSL) - Grams / Sqmtr of coated foil |
Yield - Range |
|||||
|
|
4 -6 gsm HSL |
5 – 7 gsm HSL |
6 - 8 gsm HSL |
Square metres/ Kg of coated foil |
|||
|
|
Min. |
Max. |
Min. |
Max. |
Min. |
Max. |
|
|
0.020 |
53.9 |
64.5 |
54.9 |
65.5 |
55.9 |
66.5 |
17.2 to 16.1 |
|
0.025 |
66.3 |
79.17 |
67.3 |
80.17 |
68.3 |
81.17 |
13.9 to 13.2 |
|
0.030 |
78.8 |
93.8 |
79.8 |
94.8 |
80.8 |
95.8 |
11.7 to 11.2 |
Recommended Parameters:
|
Sealing strength (Foil + Foil) |
450 gms/15 mm (Min.) |
|
Sealing Strength (Foil + PVC/PVDC) |
650 gms/15 mm (Min.) |
|
Sealing Temperature |
200° C |
|
Sealing Pressure |
3.0 to 6.0 bar |
|
Dwell Time |
0.5 Sec |
Primer
A thin layer of de-waxed shellac or nitrocellulose is applied to de-grease the foil and promote adhesion with printing ink.
Printing
|
Printing Surface |
On Primer side and HSL side |
|
Design |
As per customer’s approved artwork and design. |
|
Colors |
Up to 8 Col on Primer side & 4 color on HSL side |
|
Length Register |
± 0.3 mm |
|
Ink Adhesion and Stability |
No peel off or breakage by scotch pull test or under sealing condition. |
Finishing
|
Reel Width |
As required or within 960 mm |
|
Reel wandering |
± 0.5 mm edge wandering |
|
Width Tolerance |
±1mm |
|
Outside Diameter |
Slit Reel – 350 & Jumbo 400 mm |
|
Core & Inside Diameter |
Cardboard, Aluminium and PVC 76 mm ID suitable for shafts and pneumatic mandrel |
|
Joints |
With red / brown colored BOPP tape with flap (max 2 per reel.) |
Packing and Labeling
|
Mode of Packing |
Sea worthy packing |
|
Labeling |
Each Reel / Jumbo Roll is identified with a sticker, which is pasted inside the core and has got following information: - Specification/ Gauge/ Width/ Lot No./ Operator No./ Date/ Set No./ Machine name/ No. of Joints. |
pecification(Structure)
PET film - Aluminum foil - LDPE
PET film LDPE Aluminum Foil LDPE Paper LDPE Aluminum Foil LDPE (Plain/Printed)
Application
1. Multilayer laminates are suitable to pack hygroscopic and moisture sensitive powder products.2. Packing of food items as confectionery products
3. Any other use with the consent of manufacturer.
CompliancesThe product is fully compliant to the tests of FDA, REACH, RoHS and anti-microbiological.
TestCertificate:
The test certificates provided on observed values with standard parameters or mutually agreed format.
Above-mentioned specifications are for general guideline only and can be changed as part of continuous improvement programmer.
The final product specification will be made as per customer requirement
|
Paper Type |
Std. Paper GSM |
GSM Tolerance |
Surface |
|
Glassine |
41.0 |
± 5% |
Suitable for printing & lamination |
|
Pet Type |
Std. Pet Thickness (mic.) |
Pet GSM |
Tolerance limit |
Surface |
|
Treated (Chemically/Corona |
12.0 |
16.8 |
± 5% |
Suitable for printing & lamination |
|
23.0 |
32.2 |
± 5% |
LDPE Film
Low density polyethylene film is made in monolayer from 100 % virgin grade raw material with MFI 6 to 8 and through autoclave (low pressure) process without any mix up. It is clear, transparent and treated for perfect lamination.
Tolerance of LDPE Film thickness and Unit Weight g/sq.mtr.
|
LDPE Gauge |
Thickness Tolerance (mic.) (±10%) |
Unit Weight g/sq.mtr.(±10%) |
||||
|
Lower |
STD |
Upper |
Lower |
STD |
Upper |
|
|
75 ( Sandwich Layer) |
16.93 |
18.82 |
20.70 |
15.58 |
17.32 |
19.05 |
|
150 (Sealant Layer) |
33.88 |
37.65 |
41.41 |
31.17 |
34.64 |
38.10 |
|
200 (Sealant Layer) |
45.17 |
50.19 |
55.20 |
41.56 |
46.18 |
50.79 |
Foil Rolled from Aluminum Alloy - AA 1235 grade imported foil stock conforming to ICH Q3D Schedule, Rolled with FDA approved consumables and international guidelines on Health and Safety.
|
Standard Foil Thickness (mm) |
Tolerance Limit mm (±8%) |
|
0.009 |
± 0.00072 |
|
0.012 |
± 0.00096 |
|
0.030 |
± 0.0024 |
Tolerances of Foil Gauge and Unit Weight:
|
Foil Thickness mm |
Thickness Tolerance (mm) (±8%) |
Unit Weight g/sq.mtr. (±8%) |
Temper |
Pin Holes (Nos./sq.mtr) |
||||
|
Lower Value |
Standard Value |
Upper Value |
Lower Value |
Standard Value |
Upper Value |
|
|
|
|
0.009 |
0.0083 |
0.009 |
0.0097 |
22.49 |
24.39 |
26.28 |
Soft |
150 |
|
0.012 |
0.0110 |
0.012 |
0.0130 |
29.81 |
32.52 |
35.23 |
Soft |
50 |
|
0.030 |
0.0276 |
0.030 |
0.0324 |
74.79 |
81.3 |
87.80 |
Soft |
0 |
Recommended Operating Condition
|
Peeling Strength (Bond strength between PET & Alu.Foil) |
150 gms/15 mm (Min.) |
|
Peeling Strength (Bond strength between Alu.Foil & LDPE ) |
250 gms/15 mm (Min.) |
|
Sealing Strength (Bond Strength between LDPE to LDPE) |
550 gms/15 mm (Min.) |
|
Sealing Temperature |
160° C |
|
Sealing Pressure |
3.0 to 6.0 bar |
|
Dwell Time |
1.0 Sec |
Printing
|
Printing Surface |
On Pet/Paper Side |
|
Design |
As per customer’s approved artwork and design. |
|
Colors |
Up to 8 Col on Primer side |
|
Length Register |
± 0.3 mm |
Finishing
|
Reel Width |
As required within 900 mm |
|
Reel wandering |
± 0.5 mm edge wandering |
|
Width Tolerance |
±1mm |
|
Outside Diameter |
Slit Reel – 350 & Jumbo 400 mm |
|
Core & Inside Diameter |
Cardboard, Aluminium and PVC 76 mm ID suitable for shafts and pneumatic mandrel |
|
Joints |
With red / brown colored BOPP tape with flap (max 2 per reel.) |
Packing and Labeling
|
Mode of Packing |
Sea Worthy Packing |
|
Labeling |
Each Reel / Jumbo Roll is identified with a sticker, which is pasted inside the core and has got following information: -
Specification/ Gauge/ Width/ Lot No./ Operator No./ Date/ Set No./ Machine name/ No. of Joints. |
