CRESCENDO make Airshower is designed and built to remove surface particles from personnel like lint, dirt, dust, etc.. from the personnel entering or exiting the clean room area.

• SS 304 / CRCA powder coated construction except Filters and motor-blower assemblies which will be in standard execution.
• Minipleat HEPA Filter with hot melt technology, which conforms to EU 13 Grade, with an efficiency rating better than 99.99% for 0.3 µ at supply position.
• Intermediate filter which conforms to EU 7 Grade, with efficiency of 95% down to 3 micron. These Filters are basically made from micro-Fibre-glass media and are inherently washable.
• Primary pre filter for suction, which conforms to EU 6 Grade, with efficiency of 95% down to 5 micron. These Filters are basically made from micro-Fibre-glass washable media.
• Motor, Blower provided are statically and dynamically balanced to supply air flow with sufficient capacity and static pressure for entire life of HEPA. Blower is high performance, noise abated and light weighted.
• SS 304 / CRCA powder coated Double Walled Side Panels.
• Magnehelic Differential Pressure Gauge (0 - 25 mm or 0-50 mm) to monitor pressure drop across HEPA Filter.
• Electrical control panel mounted on the side panel of the unit.
• Fluorescent Light (250 Lux)
• ON/OFF Switches for motor & lights
• DOP Test port at upstream of HEPA filter.

• Client to ensure that floor is properly leveled; so that the equipment is installed with covings flush with the floor to avoid any gap.
• Client to confirm the location of supply pendant to enable us to decide on the entry of main cable in the unit to avoid any loose from projecting out.
• Concealing of electrical cabling (if so required ) is in Client's scope.
• Any electrical cabling required between control panel to the supply point is in Client's scope.
• Client to provide facility of 20 psig compressed air / nitrogen cylinder any compressed gas not harmful to personnel for carrying out the HEPA Filter Integrity Test.

• HEPA Filter Integrity Test
• Particle Count Test
• Air Velocity Measurement Test
• Smoke Profile Test (Video Shooting/ Photography to be arranged by client )

Air cleanliness : ISO Class 5

Nozzles Qty : 5 Nos on either side

Air Flow : Horizontal cross flow with a duration of 12 seconds

Noise Level : Less than 65 dB when Ambient is not greater than 55 dB

Vibration Level : Minimum

Power Supply : 230 V AC 1-Ø 50HZ

CRESCENDO make Airshower is designed and built to remove surface particles from personnel like lint, dirt, dust, etc.. from the personnel entering or exiting the clean room area.

• SS 304 / CRCA powder coated construction except Filters and motor-blower assemblies which will be in standard execution.
• Minipleat HEPA Filter with hot melt technology, which conforms to EU 13 Grade, with an efficiency rating better than 99.99% for 0.3 µ at supply position.
• Intermediate filter which conforms to EU 7 Grade, with efficiency of 95% down to 3 micron. These Filters are basically made from micro-Fibre-glass media and are inherently washable.
• Primary pre filter for suction, which conforms to EU 6 Grade, with efficiency of 95% down to 5 micron. These Filters are basically made from micro-Fibre-glass washable media.
• Motor, Blower provided are statically and dynamically balanced to supply air flow with sufficient capacity and static pressure for entire life of HEPA. Blower is high performance, noise abated and light weighted.
• SS 304 / CRCA powder coated Double Walled Side Panels.
• Magnehelic Differential Pressure Gauge (0 - 25 mm or 0-50 mm) to monitor pressure drop across HEPA Filter.
• Electrical control panel mounted on the side panel of the unit.
• Fluorescent Light (250 Lux)
• ON/OFF Switches for motor & lights
• DOP Test port at upstream of HEPA filter.

• Client to ensure that floor is properly leveled; so that the equipment is installed with covings flush with the floor to avoid any gap.
• Client to confirm the location of supply pendant to enable us to decide on the entry of main cable in the unit to avoid any loose from projecting out.
• Concealing of electrical cabling (if so required ) is in Client's scope.
• Any electrical cabling required between control panel to the supply point is in Client's scope.
• Client to provide facility of 20 psig compressed air / nitrogen cylinder any compressed gas not harmful to personnel for carrying out the HEPA Filter Integrity Test.

• HEPA Filter Integrity Test
• Particle Count Test
• Air Velocity Measurement Test
• Smoke Profile Test (Video Shooting/ Photography to be arranged by client )

Air cleanliness : ISO Class 5

Nozzles Qty : 5 Nos on either side

Air Flow : Horizontal cross flow with a duration of 12 seconds

Noise Level : Less than 65 dB when Ambient is not greater than 55 dB

Vibration Level : Minimum

Power Supply : 230 V AC 1-Ø 50HZ