High Gloss Fast Drying Flexible Acrylic Conformal Coating
ELECTOCOAT is a fast air-drying, lightweight, clear, tough and flexible acrylic coating designed primarily to protect printed circuit boards and electrical / electronic equipment against high voltage arcing, corona shorts, corrosion, ingress of moisture and fungus. It resists rust, tarnish, corrosion, moisture and has excellent waterproofing / weatherproofing abilities. ELECTOCOAT is highly abrasion & scratch resistant and protects electronic equipment completely due to its high dielectric strength. It does not contain any harmful chlorinated solvents, CFCs or ozone depleting chemicals.
Benefits

• Protects against rust, corrosion, tarnish, oxidation, moisture and weathering influences
• Provides a high-gloss, clear protective finish that remains transparent and does not fade or become yellow Provides a protective and insulating film that shields printed circuit boards from electrical leakage and short circuits
• Prevents sparking and corona discharges
• Non-conductive and has good dielectric properties
• Excellent resistance to weak acids & alkalis, water, oils and chemical fumes
• Easily solderable and very convenient for onsite repair jobs
• Conforms to requirements of specifications MIL-I-46058C

Applications
Insulation and protection of all electrical, electronic and high- tech equipment of: general electronics, printed circuit boards, thick film circuits, high voltage transformers, electrical motor coils, cables, wires; for moisture proofing and corrosion prevention of any industrial, automotive, aviation, marine and military electrical & electronic hardware.
Directions For Use - Bulk
Mask and protect areas not to be coated. Apply steady even strokes by means of brush. Component to be coated can also be dipped into the coating. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity.
Directions For Use - Aerosol
Shake can vigorously for at least one minute after bearing noise from inside the can is audible. Mask and protect areas not to be coated. Hold can 12-15 inches away from surface to be coated and spray in steady, even strokes. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity. Clean the valve by inverting the can and spraying a few short bursts till only the clear propellant comes out. Clean the actuator button orifice by means of a thin, fine wire.
Caution:- Contains flammable propellant and solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

High Gloss Fast Drying Flexible Acrylic Conformal Coating
ELECTOCOAT is a fast air-drying, lightweight, clear, tough and flexible acrylic coating designed primarily to protect printed circuit boards and electrical / electronic equipment against high voltage arcing, corona shorts, corrosion, ingress of moisture and fungus. It resists rust, tarnish, corrosion, moisture and has excellent waterproofing / weatherproofing abilities. ELECTOCOAT is highly abrasion & scratch resistant and protects electronic equipment completely due to its high dielectric strength. It does not contain any harmful chlorinated solvents, CFCs or ozone depleting chemicals.
Benefits

• Protects against rust, corrosion, tarnish, oxidation, moisture and weathering influences
• Provides a high-gloss, clear protective finish that remains transparent and does not fade or become yellow Provides a protective and insulating film that shields printed circuit boards from electrical leakage and short circuits
• Prevents sparking and corona discharges
• Non-conductive and has good dielectric properties
• Excellent resistance to weak acids & alkalis, water, oils and chemical fumes
• Easily solderable and very convenient for onsite repair jobs
• Conforms to requirements of specifications MIL-I-46058C

Applications
Insulation and protection of all electrical, electronic and high- tech equipment of: general electronics, printed circuit boards, thick film circuits, high voltage transformers, electrical motor coils, cables, wires; for moisture proofing and corrosion prevention of any industrial, automotive, aviation, marine and military electrical & electronic hardware.
Directions For Use - Bulk
Mask and protect areas not to be coated. Apply steady even strokes by means of brush. Component to be coated can also be dipped into the coating. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity.
Directions For Use - Aerosol
Shake can vigorously for at least one minute after bearing noise from inside the can is audible. Mask and protect areas not to be coated. Hold can 12-15 inches away from surface to be coated and spray in steady, even strokes. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity. Clean the valve by inverting the can and spraying a few short bursts till only the clear propellant comes out. Clean the actuator button orifice by means of a thin, fine wire.
Caution:- Contains flammable propellant and solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.