FAV range of Hydraulic Fittings provides secure, tough, and reliable tube connection that with exceptional leak-tight quality.

FAV Hydraulic Fittings are available in Stainless Steel, Brass, Steel and Monel.

Features

1)     International Standards

2)     Very effective seal between the fittings and the tubes

3)     Good vibration resistance

4)     High Pressure Rating Upto 10000 psi

For use with applications such as: Construction machinery, Textile machinery, Machine tools, Chemical, Marine, Military, and most other high pressure hydraulic applications.Applications using thick wall tubing where flaring is not practical.7000 Flareless Fittingsare NOT RECOMMENDED for use in instrumentation applications where toxic and noxious gases are present.A bite type fitting is sometimes incorrectly referred to as a compression fitting. Compression fittings are designed for use with soft tubing and are not interchangable with bite type fittings

Tubing sizes are measured in sixteenths of an inch. Available sizes are 1/8" through 2". When ordering, the tube end of the fitting must be specified first followed by the pipe thread or straight thread end. All fittings in this section are ordered as assemblies only unless otherwise specified by customers when ordering

Hydraulic fittings  consist of a body, a one-piece ferrule, and a nut are available in carbon steel, brass, and stainless steel. With a large number of configurations, there will be a fitting that is ideally suited to meet the requirements of almost any industrial application. On assembly, the ferrule “bites” into the outer surface of the tube with sufficient strength to hold the tube against pressure and seal the fluid, without considerable distortion of the inside tube diameter. Hydraulic fittings have a visible bite, allowing the fitting assembler to visually inspect the bite quality, thus significantly minimizing the risk of improper assembly and related service problems. Hydraulic fittings are especially suitable for use with tube wall thickness ranging from medium to extra heavy. For proper bite, bottoming out the tube is essential for the make-up of the fitting. Leak-free performance is guaranteed when bite type fittings are assembled properly. No special tools are required to obtain proper installation.

Hydraulic fittings are also suitable for use with soft metal tube and various types of plastic tubes such as nylon, polyethylene, etc. When used with plastic tube, it is strongly recommended that a tube insert, be used to prevent tube pull out due to tensile loading.

Our expertise lies in successfully designing and manufacturing of Hydraulic fittings We can deliver these in different designs as per the specific application demands. The range include Flareless Fittings, Flareless Bite Type Fittings, Union Fittings, Connectors, Elbow Fittings, Adapter Fittings, Tee Fittings, Nipple fittings, End Closure fittings, Cross Fittings and Nut & Ferrule fittings.

FAV range of Hydraulic Fittings provides secure, tough, and reliable tube connection that with exceptional leak-tight quality.

FAV Hydraulic Fittings are available in Stainless Steel, Brass, Steel and Monel.

Features

1)     International Standards

2)     Very effective seal between the fittings and the tubes

3)     Good vibration resistance

4)     High Pressure Rating Upto 10000 psi

For use with applications such as: Construction machinery, Textile machinery, Machine tools, Chemical, Marine, Military, and most other high pressure hydraulic applications.Applications using thick wall tubing where flaring is not practical.7000 Flareless Fittingsare NOT RECOMMENDED for use in instrumentation applications where toxic and noxious gases are present.A bite type fitting is sometimes incorrectly referred to as a compression fitting. Compression fittings are designed for use with soft tubing and are not interchangable with bite type fittings

Tubing sizes are measured in sixteenths of an inch. Available sizes are 1/8" through 2". When ordering, the tube end of the fitting must be specified first followed by the pipe thread or straight thread end. All fittings in this section are ordered as assemblies only unless otherwise specified by customers when ordering

Hydraulic fittings  consist of a body, a one-piece ferrule, and a nut are available in carbon steel, brass, and stainless steel. With a large number of configurations, there will be a fitting that is ideally suited to meet the requirements of almost any industrial application. On assembly, the ferrule “bites” into the outer surface of the tube with sufficient strength to hold the tube against pressure and seal the fluid, without considerable distortion of the inside tube diameter. Hydraulic fittings have a visible bite, allowing the fitting assembler to visually inspect the bite quality, thus significantly minimizing the risk of improper assembly and related service problems. Hydraulic fittings are especially suitable for use with tube wall thickness ranging from medium to extra heavy. For proper bite, bottoming out the tube is essential for the make-up of the fitting. Leak-free performance is guaranteed when bite type fittings are assembled properly. No special tools are required to obtain proper installation.

Hydraulic fittings are also suitable for use with soft metal tube and various types of plastic tubes such as nylon, polyethylene, etc. When used with plastic tube, it is strongly recommended that a tube insert, be used to prevent tube pull out due to tensile loading.

Our expertise lies in successfully designing and manufacturing of Hydraulic fittings We can deliver these in different designs as per the specific application demands. The range include Flareless Fittings, Flareless Bite Type Fittings, Union Fittings, Connectors, Elbow Fittings, Adapter Fittings, Tee Fittings, Nipple fittings, End Closure fittings, Cross Fittings and Nut & Ferrule fittings.