0.040% (max) Phosphorus Socket Set Screws

Get Latest Price

MaterialMade from alloy steel with a chemical composition of: 0.28 to 0.50% Carbon, 0.040% (max) Phosphorus, and 0.045% (max) Sulfer. Also, chromium, nickel, molybdenum or vanadium should be present in a quantity sufficient to meet the strength requirements outli
Cup Point
Half-Dog PointOval Point
FinishBlack Thermal Finish
Supply TypeManufacturer, Exporter, Supplier, Retailer
Preferred Buyer Location All over the world

View More Details

Send Enquiry

Company Information

K. M. Steel India

Khetwadi, Mumbai, Maharashtra

View Number

Member Since 13 Years
Nature of Business Retailer

Ask for more detail from the seller

Contact Supplier

Report incorrect details

View Company Details

Product Details
Company Details

MaterialMade from alloy steel with a chemical composition of: 0.28 to 0.50% Carbon, 0.040% (max) Phosphorus, and 0.045% (max) Sulfer. Also, chromium, nickel, molybdenum or vanadium should be present in a quantity sufficient to meet the strength requirements outli
Designed for frequent re-setting or re-locating on hard steel shafts and where minimal damage is shafts is essential. Ground flats on the shaft improves the contacts.Designed for permanent setting on soft or hardened shafts. Deep penetration gives this style of screw the highest torsional and axial holding power. Can be used as a hangar or pivot. For shafts of Rockwell hardness C15 or more, spot point half
For permanent setting - often used instead of a dowel pin. The point should closely fit the diameter of the drilled hole, or alternatively, against the flat.The preferred style for frequent re-set on soft or hard shafts with minimum deforming. Often used for permanent setting on shafts that are spotted, splined or grooved, and for applications where the point meets the shaft on an angle. Sometimes sub
Applications/ AdvantagesMost used style Designed for fast, permanent and semi-permanent location of parts on shafts with a hardness differential of 10-15 Rockwell C points and where cutting in of the cup edge on the shaft is acceptable.
Fully-threaded, headless screw with a hex drive at one end and a protruding tip with a flat surface at the opposing end.Posseses an oval-shaped point on the end opposing the flush hex drive.
Flat PointCone Point
DescriptionFully threaded, headless screw with a hexagonal drive at one end and a cup-shaped indentation at the other.
Cup Point
Half-Dog PointOval Point
Posseses a flat surface at the end opposing the hexagoal drive. Has a shart conical-shaped point at the opposite end from the hexagonal drive.
FinishBlack Thermal Finish
Torsional StrengthSocket set screws of sufficient length should be tested to determine if that can withstand the application of the test torque outlined in the above table without evidence of the socket reaming or the screw bursting.
HardnessRockwell C45 - 53
Heat TreatmentSet screws should be heat treated via oil quenching from above the transformation temperature and then tempered at a temperature that is condusive to meeting the hardness requirements.

the cup point is the most comonly used set screw. It has a cup-shaped indentation on one end. The cup point is used for quick, permanent and semi-permanent part assemblys and where the cutting in of the cup point edge is acceptable.

Nominal Size**	Key Engage-ment (K)	Cup & Flat Point Diameter (F)		Oval Point Radius (R)	*Cone Point Angle (A)**	Half Dog Point
	Key Engage-ment (K)	Cup & Flat Point Diameter (F)		Oval Point Radius (R)		Diameter (D)		Length (H)
	Min	Max	Min	Basic		Max	Min	Max	Min
0	0.050	0.033	0.027	0.045	0.09	0.040	0.037	0.017	0.013
1	0.060	0.040	0.033	0.055	0.09	0.049	0.045	0.021	0.017
2	0.060	0.047	0.039	0.064	0.13	0.057	0.053	0.024	0.020
3	0.070	0.054	0.045	0.074	0.13	0.066	0.062	0.027	0.023
4	0.070	0.061	0.051	0.084	0.19	0.075	0.070	0.030	0.026
5	0.080	0.067	0.057	0.094	0.19	0.083	0.078	0.033	0.027
6	0.080	0.074	0.064	0.104	0.19	0.092	0.087	0.038	0.032
8	0.090	0.087	0.076	0.123	0.25	0.109	0.103	0.043	0.037
10	0.100	0.102	0.088	0.142	0.25	0.127	0.120	0.049	0.041
1/4	0.125	0.132	0.118	0.188	0.31	0.156	0.149	0.067	0.059
5/16	0.156	0.172	0.156	0.234	0.38	0.203	0.195	0.082	0.074
3/8	0.188	0.212	0.194	0.281	0.44	0.250	0.241	0.099	0.089
7/16	0.219	0.252	0.232	0.328	0.50	0.297	0.287	0.114	0.104
1/2	0.250	0.291	0.270	0.375	0.57	0.344	0.334	0.130	0.120
5/8	0.312	0.371	0.347	0.469	0.75	0.469	0.456	0.164	0.148
3/4	0.375	0.450	0.425	0.562	0.88	0.562	0.549	0.196	0.180
7/8	0.500	0.530	0.502	0.656	1.00	0.656	0.642	0.227	0.211
1	0.562	0.609	0.579	0.750	1.13	0.750	0.734	0.260	0.240

*Angle is 90-degrees (+/-2 degrees) for these lengths and over, and it is 118-degress (+/-2 degrees) for shorter lengths.

Socket Set Screws : Nominal Screw Length
Tolerance on Length	Nominal Screw Length
	Up to 0.63" (Inclusive)	Over 0.63" - 2" (Inclusive)	Over 2" - 6"
	+/-0.01	+/-0.02	+/-0.03

Socket Set Screws (Alloy Steel) ASME B18.3-2003
Nominal Size	Shortest Nominal Length to Which Column A Applies			Hex Key Size (S)	Tightening Torque (inch/lbs.)
Nominal Size	Cup & Flat Point	Cone & Oval Point	Half Dog Point	Hex Key Size (S)	Tightening Torque (inch/lbs.)
0	0.13	0.13	0.13	0.028	0.86
1	0.13	0.19	0.13	0.028	0.86
2	0.13	0.19	0.19	0.035	1.8
3	0.19	0.19	0.19	0.050	5
4	0.19	0.19	0.19	0.050	5
5	0.19	0.19	0.19	1/16	9.5
6	0.19	0.25	0.19	1/16	9.5
8	0.19	0.25	0.25	5/64	19.4
10	0.19	0.25	0.25	3/32	33.5
1/4	0.25	0.31	0.31	1/8	77.9
5/16	0.31	0.44	0.38	5/32	156
3/8	0.38	0.44	0.44	3/16	273
7/16	0.44	0.63	0.50	7/32	428
1/2	0.50	0.63	0.63	1/4	615
5/8	0.63	0.88	0.88	5/16	1315
3/4	0.75	1.00	1.00	3/8	2150
7/8	0.8	1.00	1.00	1/2	5130
1	1.00	1.25	1.25	9/16	7010